SpeeCo LS401213 User manual

VERTICAL/HORIZONTAL
LOG SPLITTERS
ASSEMBLY& OPERATING INSTRUCTIONS
LS50-634-905
MODEL NO. LS401216
25 TON
MODEL NO. LS401213
28 TON MODEL NO. LS401224
34 TON
Thissafetyalertsymbolidentifiesimportantsafetymessagesinthismanual.
Failuretofollowthis importantsafetyinformationmay resultinseriousinjury
ordeath.
Owner’s Manual
MODEL NO. LS401221
22 TON

Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
Safety Decals ....................................................................................................................... 1-2
General Safety ...................................................................................................................... 3
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter .................................................................................................. 3-4
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 5
Fire Prevention ..................................................................................................................... 5-6
Towing Safety ...................................................................................................................... 6
Assembly Instructions ...................................................................................................................... 7
Operating Instructions ....................................................................................................................... 7-9
Engine Oil Recommendations ................................................................................................ 8
Starting Instructions ............................................................................................................... 8
Towing .................................................................................................................................. 9
Operation .............................................................................................................................. 9
Maintenance ...................................................................................................................................... 9
Parts List for Models LS401221, LS401213, LS401216 and LS401224 ..................................................... 10-11
Parts Breakdown Illustration ............................................................................................................... 12
Notes ................................................................................................................................................ 13
Specifications .................................................................................................................................. Back Cover

WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
orquestionsconcerningsafeoperation.Callourcustomerservicedepartmentat1-800-525-8322to
addresstheseconcerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only.Any other use can
cause serious injury or death.
PEPER
PERPERSONALSONALPROTECTIVE EQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed shoes
andtight fitting gloves (withoutloosecuffsordrawstrings).Alwaysweara protective hearing devicewhenoperating this log
splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
fromall moving partswhen operating thislogsplitter.
PERSONALPROTECTIVE EQUIPMENT
SAFETYDECALS
Make sure that all safety warning decals are in good condition and readable.Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.
PARTNUMBER:DL52-2-9
LOCATION:TOP,FRONTEND OFTONGUE DL-52-8
DL52-2-8
PARTNUMBER:DL52-2-10
LOCATION:BRIGGS&STRATTON
ENGINES 8 H.P.AND UP
INTENDEDUSE
Page1
PARTNUMBER:DL52-2-8
LOCATION:TOP, FRONTENDOFTONGUE

PARTNUMBER:DL51-1-57
LOCATION:TOP,FORWARDSECTION
OFHYDRAULICCYLINDER
PARTNUMBER:DL51-1-32
LOCATION:TOPOFHYDRAULICCYLINDER
PARTNUMBER:DL51-1-86
LOCATION:CLEVISENDOF BEAM
NEARTILTLOCKINGPIN
28TONAND34TONMODELS ONLY
Page 2
PARTNUMBER:DL52-2-14
LOCATION:TOP,FRONTENDOFTONGUE

GENERALSAFETY
EVER
NEVER allowchildren or adultslacking proper instructionsandunderstandingto operate this logsplitter.
KEEP allpeople andpetsa minimum of10 feet awayfrom your workarea whenoperating this logsplitter. Onlythe operator
is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVERoperatethelog splitter whenundertheinfluence of alcohol,drugsormedication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
PREPARATIONOF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 26 in. in length.
WORKAREA
NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLY operate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall off.
NEVERoperateyour log splitterinan enclosed area.Exhaustfumes contain carbonmonoxidewhich can bedeadly when
inhaled.
NEVERattempttomove your log splitteroverhilly or uneven terrainwithoutatow vehicle oradequatehelp.
ALWAYS blockthewheelsto prevent movementofthe log splitter whileinoperation.
ONLY operate your logsplitter in daylightor under goodartificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
overit.
OPERATION OF THE LOG SPLITTER
ONLYoperatethelog splitter fromtheoperator zone.
TONGUE
ENGINE
BEAM
Page3
Failure to follow these instructions may result in serious injury or death.
Operator
Zone

KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER placehandsor feet betweenthelogand splitting wedge duringforwardorreverse stroke. Serious injuryordeath
could result.
NEVER straddleorstep over the logsplitterduringoperation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allowoneperson to operate thevalvewhileanother is positioning thelog.
NEVER attempt to load your log splitter when the ram or wedge is in motion.
ALWAYS use your handtooperatethe control leveronthe valve. NEVER use yourfoot,a rope oranyextensiondevice.
NEVER movethe log splitterwhilethe engine isrunning.Shut off theengineeven if youareleaving the logsplitter for a short
periodoftime.
ALWAYS avoid contactwith the mufflerandother hot areas oftheengine during operation topreventburns.
REPAIRANDMAINTENANCE SAFETY
NEVER operateyour logsplitter when itis in poormechanical conditionor in needof repair.
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the width or
height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty.
Performallrecommendedmaintenance procedures before usingyourlogsplitter.
Replaceall damaged or wornpartsimmediately.
NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer and
is within safety limits.
ALWAYS removethesparkplugwire before performing anyserviceorrepaironyour log splitter.
ALWAYS checkthe level of hydraulicoilandengine oil beforeoperation.
ALLreplacementpartsmust meet manufacturer’sspecifications.
Page4

HYDRAULICSAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replacefrayed, kinked, cracked orotherwisedamaged hydraulic hose andcomponents.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escapingfluid under pressure canhavesufficient force to penetrateskincausing serious personal injuryoreven death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seekprofessionalmedical attention immediately ifinjured by escaping hydraulicfluid.Serious infection orreaction
candevelop if proper medicaltreatmentis not administered immediately.
ALWAYS besuretorelieve all pressurebyshuttingofftheengineand moving the valvecontrolhandle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER removethe cap from thehydraulictank or reservoirwhilethe log splitterisrunning. Hot oil underpressure
could result in serious injury.
NEVER adjustthe hydraulic valve.The pressure reliefvalveon your log splitterispreset at thefactory. Onlyaqualified
servicetechnicianshould perform thisadjustment.
FIREPREVENTION
NEVER operateyour log splitterneara flame orspark.Hydraulic oil and gasolineare flammable and canexplode.
NEVER fillthe gastankwhile the engineis hot orrunning.Allowthe engine tocool before refueling.
NEVER smokewhile operating orrefuelingyour log splitter.Gas fumes caneasilyexplode.
ONLY refuel your log splitter in a clear area with no gas fumes or spilled gas.
ALWAYS use an approved fuel container.
ALWAYS replace the gas cap securely.
If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition
untilthe spilled gas hasevaporated.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measureagainst possible flyingsparks.
ALWAYS drainthefuel tankpriorto storage toavoidthe potential firehazard.
ALWAYS store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.
NEVER storegasoline in the houseornear a heatingappliance.
Page5

IMPORTANTNOTE:
Thislog splitter isequippedwith an internal combustionengine and should notbeused on ornearany unimproved forest-
covered,brush-coveredor grass-covered landunlesstheengine’s exhaust system isequippedwitha spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective working order by the
operator. In the state of California a spark arrester is required by law. Other states have similar laws. Federal laws apply on
federallands.Asparkarrestermuffler(optionalbymanufacturer) is availableasan accessory at yournearestengine dealer.
Always check the legal requirements in your area.
TOWINGSAFETY
ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing vehicle
and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning.Always use
a Class I, 2” ball with this log splitter.
NEVER carryany cargo orwood on yourlog splitter.
NEVER allow anyone to sit or ride on your log splitter.
ALWAYS disconnect your logsplitterfrom the towing vehiclebeforeoperating it.
ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
ALWAYS allowforadded length of yourlogsplitter when turning,parking,crossing interesectionsandin all driving
situations.
NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could result in
loss of control, damage to the equipment, serious injury or death. Adjust towing speed for terrain and conditions. Be extra
cautiouswhen towingover rough terrainespeciallyrailroadcrossings.
Page6

EMBLYINSTRUCTIONS
NOTE: ThefollowinginstructionspertaintofourSpeeCologsplitters,the22ton(LS401221), 25ton(LS401216),28ton(LS401213)
andthe34ton(LS401224).Thefourmodelssharemostofthecomponentparts.Anydifferencesarenotedinthepartslistandassembly
instructions.
NOTE: Thislogsplitterwaspartiallyassembledatthefactory.Refertothedrawingandpartslistshoulditbecomenecessarytodisassemblethe
unitforrepairorreplacementofparts.
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or
delivering carrier.
STEP 2: Attach the tongue (3) to the tank/axle (2) as shown in the diagram using the two 1/2 in. NC x 4-1/2 in. hex cap screws (48), 1/2 in.
lockwashers(47)and1/2in.NChexnuts(46)fromthehardwarekit.Tighten.Makesurethegroundstand(24)isintheverticalposition.
NOTE:Flatwashersareincludedinthehardwarekitshoulditbenecessarytousethemasspacers.Thiswilleliminateplaybetweenthe
tongueandthetank/tonguemountingplate.
STEP 3:
STEP 4: Standthebeam(1)uponend.NOTE:Atleasttwopeoplearerequiredtoraisethebeamforthe28tonand34tonmodelstoinsure
safety and prevent injury. Make sure that the beam is stable. Remove the pivot pin (52) and the clip pin (53) from the tank/axle (2). Roll
the axle/tongue assembly into position between the two tabs on the beam (1). Slide the pivot pin (52) through the holes and lock in place
with the clip pin (53).
STEP 5: Connecttheendofthe1/2in.I.D.x44in.(28&34tonmodels)or1/2in.I.D.x42in.(22&25tonmodels)hydraulichose(21)coming
fromthefitting(20)onthepump(9)tothefitting(75)onthevalve(5).
STEP 6: Slideonehoseclamp(50)ontheendofthe3/4in.I.D.x37in.(28tonand 34tonmodels)or3/4in.I.D.x32-1/2in.
(22 & 25 ton models) hydraulic hose (49) that comes from the fitting on the tank/axle (2). Then connect the hose to the fitting (69) on the
valve(5).Tightenthehoseclamp.
STEP 7: Iftheoptionalfenderkit(standardonthe34tonmodel)waspurchased,attachthefenders(44)tothetank/axle(2)usingthe1/4in.NC
x3/4in.hexcapscrews(43),1/4in.flatwashers(42),1/4in.lockwashers(41)and1/4in.hexnuts(40).Tighten.
IMPORTANT: Theengineandhydraulictankareshippedwithoutoil.Seetheengineoperatingandmaintenanceinstructionsmanualpackedwith
yourlogsplitterforthe typeofcrankcaseoil,fuel,etc.Theenginemanufacturerrecommendslead-freegasolineonly.
Page7
ASSEMBLYINSTRUCTIONS
Removetherubbercoveringfromthetwospindlesonthetank/axle(2).Thewheelbearingcups,bearingcones,greasesealsand
hubcapsarealreadyassembled.Bearingconeshavebeengreasedatthefactory.Removetheblue,plasticprotectivecoveringfrom
thewheelhubs.Mountthewheels(54)tothespindlesonthetank/axle(2)usingthe3/4in.lightflatwasher(59)and3/4in.slottednut(60)
fromthehardwarekit.Therearetwotypesoflightflatwashers(59).Usetheonesthatbestallowthewheeltorotatefreelyafterthe3/4in.
slottednut(60)istighteneddownandbearingplayisremoved. Installthecotterpin(61)andthehubcap(62)fromthehardwarekit.
Repeatstep4fortheotherwheel.
OPERATING INSTRUCTIONS
WARNING: Read and thoroughly understand all instructions and safety information before operating this
log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log
splitter who has not read this manual. As with all power equipment a log splitter can be dangerous if it
isassembled or usedimproperly.Do notoperatethis log splitterifyou havedoubtsor questions concerning
safeoperation.Callourcustomer servicedepartment at1-800-525-8322toaddressthese concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
CAUTION: DO NOT START OR RUN THE ENGINE WITHOUT OIL INTHE HYDRAULIC RESERVOIRAND ENGINE.

STEP2:ThehydraulicreservoirshouldbefilledwithanSAE20hydraulicoil.Ifhydraulicoilisdifficulttoobtain,automatictransmissionfluidcan
be substituted and should be used instead of hydraulic oil when temperatures are below 32 degrees F. Use only clean oil and take care to
prevent dirt from entering the hydraulic reservoir.
CAUTION: WHEN TIGHTENING THE BREATHER CAP ON THE TANK, POINT THE HOLE AWAY FROM THE ENGINE
AND THE OPERATOR ZONE.
ENGINE OIL RECOMMENDATIONS
1) 25 Ton, 28 Ton and 34 Ton Models- For temperatures above 40 degrees F use an SAE 30W oil. Using multigrade oil may increase oil
consumption. Using SAE 30W oil below 40 degrees F will result in hard starting and possible engine bore damage. For temperatures below
40 degrees F use an SAE 10W-30 or SAE 5W-30 oil. Oil capacity is about 1-1/2 quarts (48 ounces; 1.4 liters).
2) 22 Ton Model- For temperatures above 40 degrees F use an SAE 30W oil. Using multigrade oils may increase oil consumption. Using SAE 30W
oil below 40 degrees F will result in hard starting and possible engine bore damage. For temperatures below 40 degrees F use an SAE 10W-30
or SAE 5W-30 oil. Oil capacity is approximately 5/8 quart (20 ounces; 0.6 liter).
DIRECTIONS FOR FILLING HYDRAULIC SYSTEM
Fill the hydraulic reservoir with at least five gallons of hydraulic fluid (25 ton, 28 ton & 34 ton models). Use at least four gallons for the 22 ton model.
After the hydraulic reservoir and the engine crankcase are filled with oil, start the engine. The hydraulic pump should prime itself. With the engine
running, move the hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air. When the cylinder is fully extended,
retract it. Repeat this procedure several times. An erratic movement of the cylinder indicates that there is still air in the system. More oil should then
beaddedtobringthefluidleveluptothe“OK”rangeonthedipstick.Totalhydrauliccapacitiesareasfollows:25,28and34tonmodels-31quarts;22ton
model-20quarts.NOTE:Ifthetankisoverfilled,itwilltendtoexpeloilfromthebreathercapwhenthecylinderisretracted.Afteraddingmoreoiltothetank,
cyclethecylinderagainuntilithasaconstantspeedindicatingthatallairhasbeenexpelled.Checktheoillevelinthereservoiragainwiththedipstickto
makesureitisinthe“OK”range.Donot fillbeyondthe“OK”rangeonthedipstick.
STARTING INSTRUCTIONS
Refer also to the Engine Operating and Maintenance Instructions manual for your particular log splitter.
1) 25Ton,28Ton and 34Ton Models with10.5 h.p.Engine
a) Move the throttle lever to “FAST”. Always operate the engine with throttle lever in the “FAST” position
b) Move choke control lever to “CHOKE” position.
c) Grasp rope handle and pull slowly until resistance is felt. Then pull rapidly to start engine and avoid engine kickback.
d) Allow the engine to warm up. If operating in warm weather, move the choke control lever toward “RUN” a short distance at a time over
several seconds. For cold weather operation do this procedure over several minutes. Operate with choke lever in the “RUN” position.
e) To stop engine, move the throttle lever to the “STOP” position.
2) 22Ton Modelwith6.5h.p.EngineandPrimer
a) Move control lever to “FAST.”
b) Push primer bulb three (3) times.
NOTE: DO NOT USE PRIMER TO RESTART A WARM ENGINE AFTER A SHORT SHUTDOWN.
c)Graspstarterhandleandpullropeoutslowlyuntilresistanceisfelt.Thenpullroperapidlywithfullarmstroke.Letropereturntostarter
slowly.
d)Whenenginestarts,leavethecontrolleverat“FAST.”Thethrottlemustbeinthe“FAST”positionformaximumperformance.
Page8

STEP 3: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood, the throttle should
be set at the maximum setting to develop the horsepower required for the pump.
STEP 4: TOWING
Thelogsplitterisequippedwithpneumatictires,aClassIcoupler(2in.diameterballrequired)and safetychains.Beforetowing,
thesafetychainsmustbesecuredtothehitchorbumperofthevehicle.Localregulationsshouldbecheckedregardinglicensing,lights,
towing,etc.SeealsoTowingSafetyonpage6ofthismanual.
STEP5:OPERATION
1)Setupthelogsplitterinaclear,levelareaandblockthewheels.Makesurethatthesuctionportonthetanksisalwaysonthelower
sideofthelogsplitter.
2) Place a log on the beam against the foot plate. Make sure that the log is securely on the foot plate and up against the beam.
3)Depressthevalvehandlesothatthecylinderwilldrivethewedgeintothelog.Extendthecylinderuntilthelogsplitsortothe
endof itsstroke.Iftheloghasnotcompletelysplitafterthecylinderhasreachedtheendofitsextension,retractthecylinder.
IMPORTANT:Leavingthevalveinthe“actuate”positionattheendofthestrokemaydamagethepump.Alwaysuseextracare
when splitting logs with unsquare ends.
NOTE: For operation in wooded areas, obtain a spark arrestor for the exhaust system. See the engine operating and maintenance manual
andcheckwithyourauthorizedBriggs&Strattonservicecenter.SeealsoFirePreventiononpage5and6ofthismanual.
IMPORTANT: TO EXTEND THE LIFE OF THE HYDRAULIC CYLINDER,AVOID “BOTTOMING OUT” WEDGE PLATE TO THE FOOT
PIECE. TO CONFORM WITH INDUSTRY SAFETY RECOMMENDATIONS, THE WEDGE STOPS 2 INCHES FROM
THE END OF THE STROKE.
MAINTENANCE
1) Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply
will cause severe damage to the pump.
3) Change the oil filter after the first 25 hours of operation. Thereafter, change the oil filter every 100 hours or seasonally, whichever comes first.
4) If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter bolt that connects the wedge to the
cylinder. The hose from the valve may need to be removed. While the log splitter is in the horizontal position, loosen the hose clamp and
disconnect the hose from the valve. Carefully lift the cylinder to allow the wedge to slide forward. The wedge can now be lifted off and
sharpened.
5) Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather from
thetankandflushwithkeroseneorliquiddetergenttoremovethedirt.
6)SeealsoRepairandMaintenanceSafetyonpage4ofthismanual.
7) All replacement parts must meet manufacturer’s specifications.
Page9
WARNING:Seesafetyinformationrelatedtooperationofthelogsplitteronpage3and4ofthismanual.Makesurethatyouhavethe
recommendedpersonalprotectiveequipmentdescribedonpage1.

Page10
ECNEREFER
.ON.ONTRAPNOITPIRCSED
REBMUN
DERIUQER
422104SLetelpmoCrettilpSgoLlatnoziroH/lacitreVnoT43
312104SLetelpmoCrettilpSgoLlatnoziroH/lacitreVnoT82
612104SLetelpmoCrettilpSgoLlatnoziroH/lacitreVnoT52
122104SLetelpmoCrettilpSgoLlatnoziroH/lacitreVnoT22
1841104SLsledoMnoT43dnanoT82rof)"8x"2/1-6(maeB 1
281104SLsledoMnoT52dnanoT22rof)"6x"6(maeB 1
2091104SLsledoMnoT43dnanoT82,noT52rofelxA/knaT 1
391104SLledoMnoT22rofelxA/knaT 1
3162104SLeugnoT 1
4711093CHledoMnoT43rofrednilyCciluardyH"42x"5 1
911093CH sledoMnoT82dnanoT52rofrednilyCciluardyH"42x"2/1-4 1
811093CHledoMnoT22rofrednilyCciluardyH"42x"4 1
5S604093CH sledoMnoT43dnanoT82,noT22rofevlaVnruteR-otuA 1
A604093CHledoMnoT52rofevlaVnruteR-otuA 1
6381104SLsledoMnoT43dnanoT82rofegdeW 1
631104SLsledoMnoT52dnanoT22rofegdeW 1
7425093CH sledoMnoT43dnanoT82,noT52rofenignElaicremmoC/lalrtsudnI.P.H5.01 1
925093CHledoMnoT22rofenignE.P.H5.6 1
8106093CHretliF 1
A106093CH )5egapnostnemeleretliftnelaviuqefotsilees(tnemelEretliF 1
B106093CHesaBretliF 1
9907093CH )senraB(sledoMnoT43dnanoT82,noT52rofpmuPmpg61 1
B507093CH)senraB(ledoMnoT22rofpmuPmpg11 1
01L428004SL )seceip3(sledoMnoT43dnanoT82,noT52rofrelpuoCenignE-pmuP 1
L528004SL )edisenigne(sledoMnoT43dnanoT82,noT52rofflaHrelpuoC.D.I"1 1
L628004SL )edispmup(sledoMnoT43dnanoT82,noT52rofflaHrelpuoC.D.I"2/1 1
L728004SL sledoMnoT43dnanoT82,noT52rofredipSrelpuoC 1
738004SLledoMnoT22rofrelpuoCenignE-pmuP 1
L338004SL )edispmup(ledoMnoT22rofflaHrelpuoC.D.I"2/1 1
L838004SL )edisenigne(ledoMnoT22rofflaHrelpuoC.D.I"8/7 1
L438004SLledoMnoT22rofredipSrelpuoC 1
21L/OwercSpaCxeH"1xCN"61/5 4
41L/OtunkcoLCN"61/5 4
61343004SL sledoMnoT43dnanoT82,noT52rofyeKenignEerauqS"4/1 1
123004SLledoMnoT22rofyeKenignEerauqS"61/3 1
71L/O sledoMnoT43dnanoT82,noT52rofwercSpaCxeH"2/1-1xCN"61/5 4
L/O ledoMnoT22rofwercSpaCxeH"2/1-1xCN"61/5 2
L/O ledoMnoT22rofwercSpaCxeH"2/1-2xCN"61/5 1
81613093CH61#pmalCesoH 2
91842093CH sledoMnoT43dnanoT82,noT52rofesoHnoitcuS"9x"1 1
142093CHledoMnoT22rofesoHnoitcuS"8x"4/3 1
02143093CHwoblEteertSeergeD09x"2/1 1
12752093CH sledoMnoT43dnanoT82,noT52rofesoHerusserPciluardyH"74x.D.I"2/1 1
932093CH ledoMnoT22rofesoHerusserPciluardyH"24x.D.I"2/1 1
22023093CHgnittiFesoHeergeD09"4/3xTPN4/3 1
32943093CHelppiN"2/1-2x"4/3 1
42062104SLdnatSdnuorG 1
528597PdnatSdnuorGrofniPgnikcoL"61/5 1
62817271WHtloBmm58x5.1x01M 1
72L/OrehsawkcoL"8/5 2
82L/OtuNxeHFN"8/5 2
92308271WHtuN5.1x01M 3
13987PdaerhTFN"8/5htiwniPretemaiD"8/7 1
23497PniPhcnyL"4/1 1
33643004SLllaB"2rofrelpuoChctiH 1
PARTS BREAKDOWN FOR LS401221, LS401216, LS401213 AND LS401224 LOG SPLITTERS

ReplacementfiltercartridgeHC390601interchangeswith:
FRAM1653A
NAPA1553
Cross # 1A9023
Baldwin#BT839
Wicks# 51553
RepairKits
HC390120F “O” Ring Kit for 4” x 24” Cylinder HC390118
HC390171 “O” Ring Kit for 4-1/2” x 24” Cylinder HC390119
HC390126 “O” Ring Kit for 5” x 24” Cylinder HC390117
HC390423 “O”RingKitforValvesHC390406AandHC390406S
HC390720B “O”Ring Kit for Pumps HC390705B andHC390709 Page11
ECNEREFER .ON.ONTRAPNOITPIRCSED REBMUN DERIUQER
43809271WHrehsaWmm01 6
53717271WH wercSpaCxeH5edarG"1xCN"8/3tloBmm511x5.1x01M 1
63617271WHtloBmm001x5.1x01M 1
73323004SLkooH"S"htiwniahCytefaS 1
543004SLkooH"S""8/3 1
93L/OsledoMnoT43dnanoT82,noT52roftunkcoLCN"61/5 4
L/OledoMnoT22roftunkcoL"61/5 3
04L/O)lanoitpo(redneFroftuNxeHCN"4/1 4
14L/O)lanoitpo(redneFrofrehsawkcoL"4/1 4
24L/O)lanoitpo(redneFrofrehsawtalF"4/1 4
34L/O)lanoitpo(redneFrofwercSpaCxeH"4/3xCN"4/1 4
44151104SL)sledomrehtollaroflanoitpo(ledoMnoT43rofredneF 2
54924004SLpaCrehtaerB 1
64L/OtuNxeHCN"2/1 2
74L/OrehsawkcoL"2/1 3
84L/OwercSpaCxeH"2/1-4xCN"2/1 2
94942093CH sledoMnoT43dnanoT82,noT22rofesoHnruteRciluardyH"73x.D.I"4/3 1
052093CH ledoMnoT52rofesoHnruteRciluardyH"2/1-23x.D.I"4/3 1
05613093CH61#pmalCesoH 2
25CW22017PniPtoviP"4/1-6x"8/5 1
35L/OniPpilC"R""8/1 1
45B213004SLylbmessAleehWdesaergerP 2
5567122EBlaeSesaerG 2
6557122EBenoCgniraeB 4
7547122EBpuCgniraeB 4
85213004SLeriTdeepS-daoR"8x08.4 2
95L/OrehsawtalFthgiL"4/3 2
0602171NHtuNdettolSFN"4/3 2
16L/OniPrettoC"2/1-1x"8/1 2
26233004SLpaCbuH 2
36L/O sledoMnoT43dnanoT82rofwercSpaCxeH5edarG"2/1-3x"2/1 1
L/O sledoMnoT52dnanoT22rofwercSpaCxeH5edarG"3x"2/1 1
460197PniPpilC 2
56A1377PniPrednilyC 1
6661371WFrehsawtalF 1
76743093CHgnittiFebuT 2
86643093CHebuTleetSretemaiD"2/1 1
96023093CHgnittiFeergeD09"4/3xTPN4/3 1
07343093CHelppiNxeH"2/1-"2/1 1
17113093CHgnihsuBrecudeR"2/1-"4/3 1
27A924093CH)evlav(eldnaH 1
434093CHeldnaHevlaVrofkniLniahC 1
534093CHtekcarBgnitnuoMeldnaHevlaV 1
37L/OtuNxeHCN"2/1 1
47471104SLtemmorG.D.I"4/1-1 1
57203093CHeergeD09woblEleviwS 1
651104SLsledoMnoT43dnanoT82roftiKerawdraH 1
551104SLsledoMnoT52dnanoT22roftiKerawdraH 1
.serotsmrafdnaerawdrahhguorhtelbaliavasrenetsafnommoC.yllacolniatbO-L/O

Page12
LS401221, LS401216, LS401213 and LS401224 Log Splitters

Page13
NOTES
Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________
_______________________
_______________________
_______________________

SPECIFICATIONS
*Idealcasecycletimes.Actualcycletimeswillvarydependingontemperature,altitude,enginespeed,pumpefficiency,etc.
122104SL.ONLEDOM 612104SL.ONLEDOM 312104SL.ONLEDOM 422104SL.ONLEDOM
GNITTILPSMUMIXAM ECROF
snoT22snoT52snoT82snoT43
ENIGNE
nottartS&sggirB.P.H5.6 nottartS&sggirB.P.H5.01 laicremmoC/lairtsudnI nottartS&sggirB.P.H5.01 laicremmoC/lairtsudnI nottartS&sggirB.P.H5.01 laicremmoC/lairtsudnI
REDNILYC
ekortS"42XretemaiD"4ekortS"42XretemaiD"2/1-4ekortS"42XretemaiD"2/1-4ekortS"42XretemaiD"5
EVLAV
nruteR-otuAnruteR-otuAnruteR-otuAnruteR-otuA
PMUP
mpg11egatS-owTmpg61egatS-owTmpg61egatS-owTmpg61egatS-owT
HTGNELGOLMUMIXAM
"62"62"62"62
*EMITELCYC
sdnoceS41sdnoceS21sdnoceS21sdnoceS51
SERIT
citamuenP"8X08.4citamuenP"8x08.4citamuenP"8X08.4citamuenP"8X08.4
EGDEW
sgniWredaerpShtiwhgiH"7sgniWredaerpShtiwhgiH"7sgniWredaerpShtiwhgiH"8sgniWredaerpShtiwhgiH"8
EZISMAEB
"6X"6"6X"6"8X"2/1-6"8X"2/1-6
CILUARDYHLATOT YTICAPAC
strauQ71strauQ13strauQ13strauQ13
RETLIF
elbaecalpeRnO-nipSelbaecalpeRnO-nipSelbaecalpeRnO-nipSelbaecalpeRnO-nipS
THGIEH
noitisoPlacitreVni"27 noitisoPlatnoziroHni"24 noitisoPlacitreVni"27 noitisoPlatnoziroHni"24 noitisoPlacitreVni"27 noitisoPlatnoziroHni"24 noitisoPlacitreVni"27 noitisoPlatnoziroHni"24
HTGNEL
'87"87"87"87
HTDIW
"94"94"94"94
THGIEWGNIPPIHS
.sbl525.sbl295.sbl556.sbl576