Spektrum NX6 User manual

Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
6®
®
NX6

2SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This
product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible compo-
nents or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS
Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby,
LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products
claiming compatibility with DSM or Spektrum technology.
NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby
disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.
Age Recommendation: Not for Children under 14 years. This is not a toy.
WARRANTY REGISTRATION
Visit spektrumrc.com today to register your product.
NOTICE: While DSMX technology allows you to use more than 40 transmitters simultaneously, when using DSM2 receivers, DSMX
receivers in DSM2 mode or transmitters in DSM2 mode, do not use more than 40 transmitters simultaneously.
General Notes
• Models are hazardous when operated and maintained incorrectly.
• Always install and operate a radio control system correctly.
• Always pilot a model so the model is kept under control in all
conditions.
• Please seek help from an experienced pilot or your local
hobby store.
• Contact local or regional modeling organizations for guidance
and instructions about ying in your area.
• When working with a model, always power on the transmitter
rst and power off the transmitter last.
• After a model is bound to a transmitter and the model is set
up in the transmitter, always bind the model to the transmitter
again to establish failsafe settings.
Pilot Safety
• Always make sure all batteries are fully charged before ying.
• Time ights so you can y safely within the time allotted by
your battery.
• Perform a range check of the transmitter and the model
before ying the model.
• Make sure all control surfaces correctly respond to transmitter
controls before ying.
• Do NOT y a model near spectators, parking areas or any
other area that could result in injury to people or damage to
property.
• Do NOT y during adverse weather conditions. Poor visibility,
wind, moisture and ice can cause pilot disorientation and/or
loss of control of a model.
• When a ying model does not respond correctly to controls,
land the model and correct the cause of the problem.
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-
date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and serious injury
OR create a high probability of supercial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
NOTICE
Meaning of Special Language

3SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
• NX6 Transmitter (SPM6775, SPMR6775)
• AR6610T Telemetry Receiver (SPM6775)
• Manual
BEFORE USING YOUR TRANSMITTER
Before going any further, visit the Spektrum Community website at spektrumrc.com to register your transmitter and
download the latest Spektrum AirWare™ rmware updates. A registration reminder screen occasionally appears until
you register your transmitter. When you register your transmitter, the reminder screen does not appear again.
BOX CONTENTS
Support Videos:
For helpful videos on programming the NX6 and other Spektrum
AirWare™ equipped transmitters, go to www.spektrumrc.com/
IMPORTANT: The NX6 includes channel 7 for limited functions.
This enables you have full functionality to y BNF airplanes with
retracts, aps and SAFE select with the NX6. Channel 7 is not a
fully proportional channel on the NX6, it cannot be used in mixes,
nor does it have travel adjustment. Channel 7 can be assigned
to a switch in the System Setup -> Channel Assign menu, it can
be reversed in the Function List -> Servo Setup menu, and it will
appear in the servo monitor.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to state and local laws.
Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical
issues, excessive heat, FIRE, and ultimately injury and property damage.
• NEVER LEAVE THE BATTERY AND CHARGER UNATTENDED DURING USE
• NEVER CHARGE BATTERIES OVERNIGHT
• Read all safety precautions and literature prior to use of this product
• Never allow minors to charge battery packs
• Never drop charger or batteries
• Never attempt to charge damaged batteries
• Never attempt to charge a battery pack containing different types of batteries
• Never charge a battery if the cable has been pinched or shorted
• Never allow batteries or battery packs to come into contact with moisture at any time
• Never charge batteries in extremely hot or cold places (recommended between 50–80˚ F or 10–27˚ C) or place in direct sunlight
• Always disconnect the battery after charging, and let the charger cool between charges
• Always inspect a new battery before charging
• Always terminate all processes and contact Horizon Hobby if the product malfunctions
• Always keep batteries and charger away from any material that could be affected by heat (such as ceramic and tile), as they can
get hot
• Always end the charging process if the charger or battery becomes hot to the touch or starts to change form (swell) during the
charge process
BATTERY AND CHARGING PRECAUTIONS AND WARNINGS
SPECIFICATIONS NX6 TRANSMITTER
Type DSM2/DSMX 6 CH Telemetry Transmitter
Application Airplanes, Helicopters, Sailplanes, Multirotors
Channels 7 (6 Full Channels, 7th SAFE Select Channel)
Wireless Trainer DSM2*/DSMX Compatible
Switches 2 - 2 Position, 5 - 3 Position,
1 Momentary Button
Modulation DSM2*/DSMX
Telemetry Integrated
Bind Method Bind Button or From Within Menu
Frame Rate 22ms Default,
11ms Selectable (Digital Servos Required)
Resolution 2048
Battery 3.7V 2,000 mAh LiIon
Band 2.4GHz
Feedback Tone, Vibration, Voice
*EU versions of the NX6 are not compatible with DSM2®receivers.

4SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
TABLE OF CONTENTS
Charging the Lithium Ion Battery Pack.......................................5
Connecting the USB to a PC..........................................................5
Updating with WiFi ........................................................................5
Transmitter Functions...................................................................6
Main Screen ...................................................................................8
Navigation ......................................................................................8
Auto Switch Select ........................................................................8
External Memory card...................................................................9
Installing an external Memory card ............................................9
Internal Memory card....................................................................9
Memory card Functions..............................................................10
Update Spektrum AirWare™ Software.....................................10
Binding..........................................................................................11
Receiver Power System Requirements.....................................12
Recommended Power System Test Guidelines........................12
Model Type Programming Guide................................................13
System Setup...............................................................................14
Model Select..................................................................................14
Direct Model Access ......................................................................14
Model Type....................................................................................14
Model Name..................................................................................15
Aircraft Type...................................................................................15
Sailplane Type ...............................................................................15
Swash Type ...................................................................................15
Aircraft Options..............................................................................15
F-Mode Setup................................................................................15
Flight Mode Setup..........................................................................15
Aircraft Flight Mode Table...............................................................15
Flight Mode Setup..........................................................................16
Channel Assignment......................................................................16
Channel Input Conguration...........................................................16
Trim Setup.....................................................................................17
Model Utilities ................................................................................17
Warnings.......................................................................................19
Telemetry.......................................................................................20
Preight Setup...............................................................................21
Frame Rate....................................................................................21
Bind...............................................................................................21
Wireless Trainer .............................................................................22
Trainer FPV Mode ..........................................................................23
Digital Switch Setup.......................................................................23
Palette Utilities ...............................................................................24
User Name ....................................................................................24
Backlight .......................................................................................24
Mode.............................................................................................24
Battery Alarm.................................................................................24
Selecting a Language ....................................................................25
Inactive Alarm................................................................................25
Extra Settings.................................................................................25
Calibrate........................................................................................27
Check for Updates .........................................................................27
USB Settings..................................................................................27
Transfer Memory card....................................................................28
Memory Location...........................................................................28
Import Model.................................................................................28
Export Model .................................................................................29
Importing/Exporting Color Palettes..................................................29
Update AirWare..............................................................................30
About / Regulatory.........................................................................30
Serial Number................................................................................30
Function list..................................................................................31
Servo Setup...................................................................................31
Travel Adjust ..................................................................................31
Sub-Trim .......................................................................................31
Reverse .........................................................................................31
Dual Rates and Expo......................................................................32
Mixing ...........................................................................................33
Range Test.....................................................................................34
Timer.............................................................................................35
Telemetry.......................................................................................35
Forward Programming...................................................................36
Custom Voice Setup- Audio Events.................................................36
VTX Setup......................................................................................36
Function Bar..................................................................................37
Ticker Tape....................................................................................37
My List Setup.................................................................................37
ACRO (Airplane) ...........................................................................38
Acro Model Type ...........................................................................38
Aircraft Type...................................................................................38
Recommended Servo Connections ................................................38
Aircraft Options..............................................................................38
Elevon Servo Control.....................................................................39
Aileron...........................................................................................39
Elevator .........................................................................................39
Flap System...................................................................................39
ACRO Mixing .................................................................................39
Differential.....................................................................................40
V-Tail Differential............................................................................40
Gyro Menus...................................................................................40
HELI (Helicopter)..........................................................................41
Heli Model Type ............................................................................41
Swash Type ...................................................................................41
Collective Type...............................................................................41
Pitch Curve....................................................................................41
Swashplate....................................................................................42
Gyro ..............................................................................................42
Tail Curve ......................................................................................42
Mixing ..........................................................................................42
Sail (sailplane) .............................................................................43
Sailplane Model Type .....................................................................43
Sailplane Type ...............................................................................43
Motor ............................................................................................43
Camber Preset ..............................................................................43
Camber System.............................................................................43
SAIL Mixing ...................................................................................44
V-Tail Differential............................................................................44
MULTI (Multirotor)........................................................................45
Multirotor Model Type ....................................................................45
F-Mode Setup................................................................................45
Trim Setup.....................................................................................45
D/R and Exponential ......................................................................46
Motor Cut ......................................................................................46
Motor Curve ..................................................................................46
Physical Transmitter Adjustments.............................................47
Mode Conversion.........................................................................48
Antenna Position..........................................................................48
Troubleshooting Guide ................................................................49
1-Year Limited Warranty.............................................................50
Warranty and Service Contact Information..............................51
FCC Information...........................................................................51
FAA Information...........................................................................52
AMA National Model Aircraft Safety Code................................52
IC Information ..............................................................................52
Compliance Information for the European Union.....................52

5SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
The NX6 transmitter has an internal charger that is powered from
any common Micro USB power supply.
CAUTION: Never connect an external battery charger to
your NX6 transmitter.
Always charge the transmitter on a heat-resistant surface.
1. Power off your transmitter.
2. Connect the power supply to a power outlet using the
appropriate adapter.
3. Connect your micro USB cable to the charge port located on
the back of the NX6.
4. Disconnect the transmitter from the power supply once
charging is complete and disconnect the power supply from
the power outlet.
CAUTION: Never leave a charging battery unattended.
CAUTION: Never charge a battery overnight.
Battery Alarm
The System Settings Screen allows you to change the battery type
and low voltage alarm settings. See “System Settings” for more
information.
• An alarm will sound when the battery reaches the low voltage
limit. If this happens in ight, land immediately and recharge.
The NX6 transmitter has internal memory that enables you to
connect to your NX6 for le transfers directly through the Micro
USB connector. The USB port may be used at any time to charge
the battery, but to connect to the internal memory, you will need to
observe the following steps.
1. Connect your micro USB cable to the Micro USB connector
located on the back of the NX6.
2. Enter the Function menu and Scroll to the bottom to access the
System menu.
3. Scroll down and select USB Settings.
4. Select Access Internal Storage.
5. Transfer your les between the NX6 and your PC as needed.
6. Click back or the roller to exit and resume normal operation.
The NX6 transmitter has a WiFi capabilities to enable you to
download updates from the SpektrumRC.com website. You must
start an account at SpektrumRC.com rst on your PC, Mac, or
mobile device before you can connect with your NX6
1. Power ON your NX6 and enter the Function menu, Scroll to the
bottom to access the System menu.
2. Scroll down and select Check For Updates. The NX6 will search
for WiFi networks in range and display the options for you to
connect with.
3. Select your WiFi connection. Load the SSID and password for
connection and select Connect.
4. Select Log In and ll in your account information.
5. Select Check For Updates to check for the newest updates on
your NX6, and download them automatically.
6. If you wish to erase your registration information from your NX6
you may do so. Otherwise, select Log Out to resume normal
operation.
CHARGING THE LITHIUM ION BATTERY PACK
CONNECTING THE USB TO A PC
UPDATING WITH WIFI

6SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
TRANSMITTER FUNCTIONS
Function
1Elevator Trim (Mode 2, 4)
Throttle Trim (Mode 1, 3)
2Switch H
3Switch G
4Switch F
5
Throttle Tension Adjustment
Throttle Ratchet Adjustment
(Mode 1, 3)
6Gimbal Travel Limiter Access
Panel
7Mode Change Screw
8
Throttle/Aileron Stick (Mode 1)
Elevator/Aileron Stick (Mode 2)
Throttle/Rudder Stick (Mode 3)
Elevator/Rudder Stick (Mode 4)
Function
9Left/Right Gimbal Stick
Tension Adjustment
10 Up/Down Gimbal Stick
Tension Adjustment
11 Gimbal Travel Limiter Access
Panel
12 Aileron Trim (Mode 1, 2)
Rudder Trim (Mode 3, 4)
13 Neck Strap Mount
14 WiFi Indicator
15 Scroll wheel
16 Charge Indicator
17 LCD
18 Function Button
19 Back Button
Function
20 Clear Button
21 Speaker
22 Rudder Trim (Mode 1, 2)
Aileron Trim (Mode 3, 4)
23
Throttle Tension Adjustment
Throttle Ratchet Adjustment
(Mode 2, 4)
24 Gimbal Travel Limiter Access
Panel
25 Mode Change Screw
26
Elevator/Rudder Stick (Mode 1)
Throttle/Rudder Stick (Mode 2)
Elevator/Aileron Stick (Mode 3)
Throttle/Aileron Stick (Mode 4)
Function
27 Left/Right Gimbal Stick
Tension Adjustment
28 Up/Down Gimbal Stick
Tension Adjustment
29 Gimbal Travel Limiter Access
Panel
30 Switch D
31 Switch B
32 Switch A
33 Switch C
34 Elevator Trim (Mode 1, 3)
Throttle Trim (Mode 2, 4)
35 On/Off Switch
36 Antenna
The transmitter comes with a thin, clear plastic lm applied to some front
panels for protection during shipping. Humidity and use may cause this lm
to come off. Carefully remove this lm as desired.
3
5
4
1
2
7
6
8
9
10
11
13
12
14
16
15
17
18
19
20
21
22
23
24
25
27
26
28
31
29
30
33
34
35 36
32

7SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
TRANSMITTER FUNCTIONS
Powering the NX6 On and Off
1. Press and hold the Spektrum Logo for several seconds to turn
ON the NX6.
2. Press and hold the power button for about 4 seconds to power
OFF the NX6.
Function
1Switch I/ Bind
2Switch A
3Mounting for CSRF
4Micro USB Connector
5Memory Card Opening
6Battery Cover
Function
7Data Port
8Audio Port
9Antenna Rotation Tension
1
3
4
5
6
7
8
9
2

8SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
• Scroll the scroll wheel to move through the screen content or
change programming values. Press the scroll wheel to make
a selection.
• Use the Back button to go to the previous screen (for example,
to go from the Mixing Screen to the Function List).
• Use the Clear button to return a selected value on a screen to
the default setting.
• Direct Model Access enables you to access the Model Select
screen without powering off the transmitter. Anytime the
transmitter power is on, press the Clear and Back buttons to
access the Model Select screen.
• Press and hold the scroll wheel while powering on the
transmitter to show the System Setup list. No radio
transmission occurs when a System Setup screen is
displayed, preventing accidental damage to linkages and
servos during changes to programming.
• At the main screen you can scroll to view the servo monitor.
• The Main Screen appears when you power on the transmitter.
Press the scroll wheel once to display the Function List.
• When you want to change a value in a screen for a particular
control position, move the control to the desired position to
highlight the value you want to change, such as 0/1/2, up/
down or left/right.
Turn
Press
Press
Enter, Choose
or Exit
Move between
options or change
value in an option
Hold for 3
seconds and
release to move to
the Main Screen
Scroll HoldPress
Tip: The tick mark below shows the current switch position.
Rolling and clicking the scroll wheel turns the selected box black,
indicating that the value or condition will act on that position.
MAIN SCREEN
NAVIGATION
Auto Switch Select
To easily select a switch in a function, such as a program mix,
roll with the scroll wheel to highlight the switch selection box, and
press the scroll wheel. The box around the switch should now
ash. To select a switch, toggle the switch you wish to select.
Verify the switch selection is now displayed as desired. When
correct, press the scroll wheel to select this switch and complete
the switch selection.
Function
AModel Name
DSMX/DSM2 If not shown, this indicates not bound
Displays throttle position
DDigital Battery Voltage (an alarm sounds and the screen ashes
when battery charge gets down to 3.2V for a Li Ion battery.)
EModel Avatar
FElevator Trim (Mode 2, 4)
Throttle Trim (Mode 1, 3)
GAileron Trim (Mode 1, 2)
Rudder Trim (Mode 3, 4)
HModel Memory Timer
Function
IRudder Trim (Mode 1, 2)
Aileron Trim (Mode 3, 4)
JThrottle Trim (Mode 2, 4)
Elevator Trim (Mode 1, 3)
KTimer
E
D
BC
J
K
A
F
B
C
G
I
H

9SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
Installing an external Memory card
A Micro Memory card (not included) enables you to:
• Import (copy) models from any compatible* Spektrum
AirWare™ transmitter
• Export (transfer) models to any Spektrum AirWare transmitter*
• Update Spektrum AirWare software in the transmitter
• Install/Update sound les
• Back up models for safe keeping
To install or remove a Memory card:
1. Power OFF the transmitter.
2. Press the Memory card into the card opening with the card
label facing up as shown.
EXTERNAL MEMORY CARD
*iX12, iX20, DX20, DX18t, DX18SE, DX18G2, DX18G1, DX18QQ, DX9Black, DX9, DX10t, DX8G2, DX7G2, DX6G3, DX6e, NX6 and DX6G2
An internal Memory card is included, it cannot be removed,
but may be accessed via the USB port on the transmitter. The
internal Memory card enables you to:
• Update Spektrum AirWare software in the transmitter
• Install/Update sound les
• Back up models for safe keeping
• Import/Export Color Palettes
To connect to the Memory card:
1. Connect a Micro USB cable to your PC and the micro USB
connector on the back of the transmitter.
2. Power ON the transmitter, enter the system menu -> USB
storage, select Access Internal Storage, the NX6 will connect
to your PC.
3. Complete your le transfer(s).
4. Press the Back button or the roller to exit.
5. Disconnect the USB cable from your transmitter.
INTERNAL MEMORY CARD

10 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
MEMORY CARD FUNCTIONS
Update Spektrum AirWare™ Software
NOTICE: The orange LED Spektrum bars ash and a status bar
appears on the screen when Spektrum AirWare software updates
are installing. Never power off the transmitter when updates are
installing. Doing so may damage the system les.
NOTICE: Before installing any Spektrum AirWare les, always
Export All Models to an Memory card separate from the Memory
card containing the update. The update may erase all model les.
For more information on Spektrum AirWare software updates, visit
www.spektrumrc.com
Software updates may be completed with either the micro Memory
card or using WiFi. See the section in this manual covering WiFi
for more inforamtion about updating with WiFi.
Automatically Installing Spektrum AirWare Software Updates
1. Go to www.spektrumrc.com. Under the Setups/Updates pull
down tab, select the Firmware Updates link (shown).
2. Log into your Spektrum account.
3. Find your registered transmitter in the MY PRODUCTS list and
click on Download Updates. Follow directions on the screen
for downloading the update to an Memory card through your
computer.
4. Eject the Memory card from the computer.
5. Make sure the transmitter is powered off and install the
Memory card into the transmitter.
6. Power on the transmitter and the update automatically
installs in the transmitter.
Manually Installing Spektrum AirWare Software Updates
1. Save the desired Spektrum AirWare version to an Memory
card.
2. Install the Memory card into the transmitter.
3. Select Update Firmware in the Memory card Menu options.
The Select File screen appears.
4. Select the desired Spektrum AirWare version from the File
List. When updates are installing, the transmitter screen is
dark. The orange LED Spektrum bars ash and the update
status bar appears on the screen.
NOTICE: Do not power off the transmitter when updates are
installing. Doing so will damage the transmitter.
Screen shots from www.spektrumrc.com are correct at time of
printing but may change at a future date.

11SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
AR6610T TELEMETRY RECEIVER
(Not included with SPMR6775 transmitter only)
The Spektrum™AR6610T receiver is a full range telemetry receiver featuring
DSM®technology. It is compatible with all Spektrum™aircraft radios that
support DSM2®and DSMX®technology.
Perform the failsafe setup for the AR6610T receiver through a compatible
Spektrum Transmitter with Forward Programming. The Spektrum PC
Programmer can be used for rmware updates.
SPECIFICATIONS AR6610T
Type DSM2/DSMX 6 CH Telemetry Receiver
Application Air
Channels 6
Receivers 1
Remote Receiver
(not included) SRXL2™Remote Receiver Optional
[SPM9747]
Modulation DSM2/DSMX
Data Flight Log
Compatible No
Telemetry Integrated
Bind Method Bind Button
Failsafe Yes
Band 2.4GHz
Dimensions (LxWxH) 49.80 x 23.34 x 15.02mm
Weight 12g
Input Voltage 3.5–9V
Resolution 2048
Antenna Length 155mm and 186mm
Bind Button
Bind/Program Port
CH 1/ Smart Port
XBUS Port
SRXL2 Port
Voltage Sensor Port
CH 2
CH 3
CH 4
CH 5
CH 6
Binding
The AR6610T receiver must be bound to your transmitter before
it will operate. Binding is the process of teaching the receiver the
specic code of the transmitter so it will only connect to that spe-
cic transmitter. When new out of the package, the AR6610T will
automatically go into bind mode the rst time it is powered on.
1. Connect the optional SRXL2 remote receiver (SPM9747) if desired and
any telemetry sensors to the main receiver.
2. Push and hold the bind button on the receiver while turning the receiver
on. Release the bind button once the orange LED starts to ash
continuously, indicating that the receiver is in bind mode.
TIP: It is still possible to use a bind plug in the BIND port if desired. This
can come in handy if the receiver needs to be mounted in a location that
is difcult to access, in which case a servo extension may be used for
binding. If using a bind plug, remove after binding to prevent the system
from entering bind mode the next time the power is turned on.
3. Put your transmitter in bind mode.
4. The bind process is complete when the orange LED on the receiver is
solid.
Failsafe
In the unlikely event that the radio link is lost during use, the
receiver will enable the selected failsafe mode. Smart Safe + Hold
Last is the default setting on the AR6610T. Preset Failsafe and
SAFE Failsafe are only available through forward programming.
SmartSafe +Hold Last
If loss of signal occurs, SmartSafe™ technology moves the throttle channel
to its preset failsafe position (low throttle) that was set during binding. All
other channels will hold their last position. When the receiver detects the
signal from the transmitter, normal aircraft operation resumes.
Forward Programming
In your transmitter menu select Forward Programming -> Settings ->
• Select Failsafe -> Select each channel and assign it to Preset or Hold Last.
When you select a different channel for Output, a new group of settings
appears.
Capture Failsafe Postions ->
Hold the control sticks in the desired failsafe positions and select Apply.
Channel selections must be individually set in Forward Programming to
apply the preset positions or each channel will default to Hold Last. The
value captured will be reected in the position shown for each channel.
• Initiate Receiver Bind Mode
Gives you the option of putting the receiver into Bind Mode from this
menu.
Preset Failsafe
With preset failsafe, you can set the specic control surface positions you
want to use if the signal is lost. When the receiver detects the signal from
the transmitter, normal aircraft operation resumes.
Only available through Forward Programming
Testing Failsafe
Secure the aircraft on the ground and remove the propeller. Test
Failsafe settings by turning the transmitter RF output off and noting
how the receiver drives the control surfaces.
Receiver Power Only
• If the receiver is turned when no transmitter signal is present, the
throttle channel will not have a control signal to avoid operating or
arming the electronic speed control.
• All other channels have no output until the receiver has linked to the
transmitter.

12 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
RECEIVER POWER SYSTEM REQUIREMENTS
Inadequate power systems that do not provide the necessary
minimum voltage to the receiver during ight have become the
number one cause of in-ight failures. Some of the power system
components that affect the ability to properly deliver adequate
power include:
• Receiver battery pack (number of cells, capacity, cell type,
state of charge)
• The ESC’s capability to deliver current to the receiver in
electric aircraft
• The switch harness, battery leads, servo leads, regulators etc.
The AR6610T has a minimum operational voltage of 3.5 volts; test
the power system per the guidelines below.
Recommended Power System Test Guidelines
Perform the following test by viewing the voltage in the telemetry
display on the transmitter.
With the system on, load the control surfaces (apply pressure with your
hand) while monitoring the voltage at the receiver. The voltage should
remain above 4.8 volts, even when all servos are heavily loaded.
CAUTION: When charging Ni-MH batteries, make sure
the battery fully charges. Ni-MH batteries charged with
peak detection fast chargers have a tendency to false peak
(i.e. not fully charge), which could lead to a crash.
QuickConnect™ Technology with Brownout Detection (DSM2 Only)
The AR6610T features QuickConnect technology with Brownout
Detection.
• Should an interruption of power occur (brownout), the system
will reconnect immediately when power is restored.
• The LED on the receiver will ash slowly, indicating a power
interruption (brownout) has occurred.
• Brownouts can be caused by an inadequate power supply
(weak battery or regulator), a loose connector, bad switch,
inadequate BEC when using an electronic speed controller,
etc.
• Brownouts occur when the receiver voltage drops below
3.5 volts. This interrupts control, as the servos and receiver
require a minimum of 3.5 volts to operate.
How QuickConnect Technology with Brownout Detection Works
• When the receiver voltage drops below 3.5 volts, the system
drops out (ceases to operate).
• When power is restored, the receiver immediately attempts to
reconnect to the last two frequencies it was connected to.
• If the two frequencies are present (the transmitter was left
on), the system reconnects typically in about 4/100 of a
second.
QuickConnect with Brownout Detection is designed to allow you
to y safely through most short duration power interruptions.
However, you must correct the cause of these interruptions before
your next ight to prevent a crash.
CAUTION: If a brownout occurs in ight, determine the
cause of the brownout and correct it before attempting
to y again.

13SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
MODEL TYPE PROGRAMMING GUIDE
Menu options show up on model type selection. These menu options vary between Model Types (Airplane, Helicopter,Sailplane and
Multirotor), but are identical for all models in that type. Subsequent aircraft type (Aircraft, Swashplate,Sailplane or Multirotor) selections
make other menu options appear.
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Throttle Curve
3–Axis Gyro
Gyro (1,2,3)
Flap System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Sailplane Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Motor Curve
Camber Presets
Camber System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Control Setup
D/R and Expo
Motor Cut
Motor Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Swashplate Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Throttle Cut
Throttle Curve
Pitch Curve
Swashplate
Gyro
Tail Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start TimerSystem Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Throttle Curve
3–Axis Gyro
Gyro (1,2,3)
Flap System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Sailplane Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Motor Curve
Camber Presets
Camber System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Control Setup
D/R and Expo
Motor Cut
Motor Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Swashplate Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Throttle Cut
Throttle Curve
Pitch Curve
Swashplate
Gyro
Tail Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start TimerSystem Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Throttle Curve
3–Axis Gyro
Gyro (1,2,3)
Flap System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Sailplane Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Motor Curve
Camber Presets
Camber System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Control Setup
D/R and Expo
Motor Cut
Motor Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Swashplate Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Throttle Cut
Throttle Curve
Pitch Curve
Swashplate
Gyro
Tail Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start TimerSystem Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Throttle Curve
3–Axis Gyro
Gyro (1,2,3)
Flap System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Sailplane Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Differential
V-Tail Differential
Throttle Cut
Motor Curve
Camber Presets
Camber System
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Aircraft Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Control Setup
D/R and Expo
Motor Cut
Motor Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start Timer
System Setup
Monitor
System Setup List:
Model Select
Model Type
Model Name
Swashplate Type
F-Mode Setup
Spoken Flight Mode
Channel Assign
Trim Setup
Model Utilities
Warnings
Telemetry
Preflight Setup
Frame Rate
Bind
Serial Port Setup
Trainer
Analog Switch Setup
Digital Switch Setup
Center Tone
Sound Utilities
System Settings
WiFi Utilities
USB Settings
Transfer SD Card
About/Regulatory
Function List:
Servo Setup
D/R and Expo
Throttle Cut
Throttle Curve
Pitch Curve
Swashplate
Gyro
Tail Curve
Mixing
Range Test
Timer
Telemetry
Forward Programming
Audio Events
VTX Setup
Function Bar
Start TimerSystem Setup
Monitor

14 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
Enter the System Setup menu to dene baseline settings for your model such as what type of aircraft, wing type, ight mode setup, etc.
The options chosen in the system menu congures the function list for the chosen model number for your requirements. Some options,
such as the ap menu, will not appear at all in the function list until they are selected within the System Setup menu.
Press and hold the scroll wheel while powering on the transmitter to show the System Setup list. No radio transmission occurs when a
System Setup screen is displayed, preventing accidental damage to linkages and servos during changes to programming.
You can also enter the System Setup from the Function list without turning the transmitter off. A Caution screen will appear that warns
that RF will be disabled (the transmitter will no longer transmit). Press YES if you are sure and want to access the System List. If you are
not sure, press NO to exit to the main screen and continue operation.
Model Select enables you to access any of the 250 internal model
memory locations in the Model Select list.
1. Scroll to the desired model memory in the Model Select list.
2. When the desired model memory is highlighted, press the
scroll wheel once to select the model. The transmitter returns
to the System Setup List.
3. Add a new model by rolling to the bottom of the list. You will
then be prompted with the Create New Model screen, with
the option to create a new model or cancel. If you select
Cancel, the system will return to the Model Select function. If
you select Create, the new model will be created and now be
available in the model select list.
Direct Model Access
Press the Clear and Back buttons from the Main Screen or a
telemetry screen to access Model Select.
SYSTEM SETUP
Select from Airplane, Helicopter, Sailplane or Multicopter model
types.
IMPORTANT: When you select a new model type, you will delete
any programming data in the current model memory. Always
conrm the desired model memory before changing model
types. It will be necessary to re-bind after resetting the model
type.
To change the model type:
1. Scroll to the desired model type and press the scroll wheel.
The Conrm Model Type screen appears.
2. Select Yes and press the scroll wheel to conrm the model
type. All data will be reset. Selecting No will exit the Conrm
Model Type screen and return to the Model Type screen.
Model Select
Model Type
If you do not press YES or NO, the system will exit to the main
screen and continue operation within approximately 10 seconds.
WARNING: Do not press YES unless the model is turned
off or the model is secured.

15SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
Use the Flight Mode Setup menu to assign switches to ight modes.
Flight Mode Setup
You can assign up to ten ight modes using any combination
of up to three switches, maximum ight modes and switches
available dependent on model type. You can also assign a priority
switch. When the priority switch position is active, only the current
ight mode is active, regardless of other switch positions.
Aircraft Flight Mode Table
You can assign the available ight modes (up to 5 for Sail) to each
of the switch positions (up to 3 switches can be used for Aircraft/
Sailplane). Press NEXT from the Flight Mode Name page to access
the ight mode table assignment page when Custom ight mode has
been selected in the Flight Mode Setup page. The combination of up
to switches can be used to access all of the ight modes available.
Number
of Flight
Modes
2 3 3* 4 4 5
Switch 1
(number of
positions)
2P 3P 2P 2P 3P 3P
Switch 2
(number of
positions)
2P 3P 2P 3P
Flight
Mode
1
Launch Launch Launch Launch Launch Launch
2 Cruise Cruise Cruise Cruise Cruise Cruise
3 Land Land Land
4 Thermal Thermal Thermal Thermal
5 Speed Speed
*Must be set up in a 4/5 ight mode.
Below is an example of 5 ight modes, you can congure up to 10 ight
modes with the NX6
Model Name enables you to assign a custom name to the current
model memory. Model names can include up to 20 characters,
including spaces.
To add letters to a Model Name:
1. Scroll to the desired letter position and press the scroll wheel
once. A ashing box appears.
2. Scroll left or right until the desired character appears. Press
the scroll wheel once to save the character.
3. Scroll to the next desired letter position. Repeat Steps 1 and
2 until the Model Name is complete. Insert a character by
selecting <+> or delete a character by selecting <->.
4. Select BACK to return to the System Setup list.
To erase a character:
1. Press CLEAR while the character is selected.
2. Press CLEAR a second time to erase all characters to the
right of the cursor.
Aircraft Type This menu only available in Airplane Mode. See ACRO (Airplane) section for set up.
Sailplane Type This menu only available in Sailplane Mode. See SAIL (Sailplane) section for set up.
Swash Type This menu only available in Helicopter Mode. See HELI (Helicopter) section for set up.
Aircraft Options This menu only available in Multirotor Mode. See MULTI (Multirotor) section for set up.
SYSTEM SETUP
Model Name
F-Mode Setup
Mode Number of Switches Number of Flight Modes
ACRO 3 10
HELI 3 (including Throttle Hold) 5 (including Throttle Hold)
SAIL 3 10
MULTI 2 5

16 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
Enables you to assign custom names to the Flight Mode positions.
Flight Mode names can include up to 20 characters, including
spaces.
To change the Flight Mode name:
1. Scroll to the Flight Mode name you wish to change and press
the scroll wheel.
2. Scroll to the character position you wish to change and press
the scroll wheel once. A ashing box appears.
3. Scroll left or right until the desired character appears. Press
the scroll wheel once to save the character. Insert a character
by selecting <+> or delete a character by selecting <->.
4. Repeat Steps 2 and 3 until the Model Name is complete.
5. Select BACK to return to the Flight Mode Names list.
The Channel Assignment function allows you to reassign almost
any receiver channel to a different transmitter channel. For
example, the receiver gear channel could be re-assigned to the
transmitter throttle channel.
1. Scroll to the receiver channel you wish to change.
2. Press the scroll wheel once and scroll left or right to change
the receiver input selection.
3. Press the scroll wheel a second time to save the selection.
IMPORTANT: You cannot assign a mix to a channel that has
been moved. Create the mix rst, then move the channel.
The Channel Input Conguration screen enables you to assign a
transmitter channel to a different control stick or switch.
1. Select NEXT on the RX Port Assignments screen to access
the Channel Input Conguration screen.
2. Scroll to the transmitter channel you wish to re-assign and
press the scroll wheel. The box around the current input
selection ashes.
3. Scroll left or right to select the desired control stick or switch.
4. Press the scroll wheel to save the selection.
SYSTEM SETUP
Flight Mode Setup
Channel Assignment
Channel Input Configuration

17SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
In the Model Utilities function you can create a new model, delete
a model, copy a model, reset a model to default settings and sort
the model list.
Use the Trim Setup screen to change the size of the trim step and
the trim type.
Trim Step
Adjusting the trim step value determines how many “clicks” of trim
you input each time you press the trim button. Changing the trim
step value to 0 disables the trim for the channel.
To change the trim step value:
1. Scroll to the trim step channel you wish to change.
2. Select the trim step value and scroll left or right to change
the value.
3. Press the scroll wheel to save the selection.
Trim Type
The two Trim Type options are Common and F Mode.
Common trim type maintains the same trim values for all ight
modes.
F Mode trim type enables you to save trim values for individual
ight modes if you nd, for example, the aircraft requires aileron
trim in Flight Mode 1 but not in Flight Mode 2.
Trim Assignment
In a few instances, you can reassign a trim to a different
location.
Aircraft Model Type
Throttle
• Throttle Digital trim button (default)
Throttle Trim Type
• Common
• Flight Mode
Trim Location
Normal and Cross trim types are available. Normal trims align with
the control stick; for example, the throttle trim is next to the throttle
stick.
Cross trims reverse the position of the trims; for example, the
throttle trim is next to the elevator stick and vice versa.
To change the Trim Position from Normal to Crossed, select Normal
at the bottom of the Trim Setup screen and press the scroll wheel.
IMPORTANT: Crossed trims will cross both sets of trims for both
gimbals.
SYSTEM SETUP
Trim Setup
Model Utilities

18 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
The Model Copy menu enables you to duplicate model
programming from one Model List location to another.
Use Model Copy to:
• Save a default model copy before experimenting with
programming values
• Expedite programming for a model using a similar
programming setup
IMPORTANT: Copying a model program from one model
memory to another will erase any programming in the “To”
model memory.
To copy model programming:
1. Make sure the model program you wish to copy is active. If
the desired model program is not active, select Cancel and
change the active model in the Model Select menu.
2. Select the model memory next to “To” and scroll to the
desired model memory. Press the scroll wheel once to save
the selection.
3. Select Copy and the Conrm Copy screen appears.
4. Select Copy to conrm. Selecting Cancel will return to the
System Setup screen.
5. Select the “To” model as the current model, then bind the
transmitter and receiver. Copying a model does not copy the
bind from the original model.
You cannot use the Model Copy screen to copy model
programming to an Memory card. To copy model programming to
the Memory card, please see “Transfer Memory card”.
SYSTEM SETUP
Copy Model
Use this selection to permanently delete a model from the model
select list. If you do not wish to delete a model, select Cancel to
exit the page.
1. To delete a model, highlight the model listed. Press to select,
then roll to the model name. Press the scroll wheel to select.
2. Select DELETE to delete the model.
Delete Model
Use this selection to create a new model in the model select list.
1. Select Create New Model. Within this screen, you will have
the option to create a new model or cancel.
2. Select the model type. Choose the aircraft image to dene the
model type for a blank model le, or select Template to load
a template le. A SAFE template and a SAFE Select template
come pre-loaded on your NX6.
• Templates are saved in the templates folder on the internal
memory (accessible with the USB connection, new .NSPM
les may be added)
• The SAFE template puts the 3 position ight mode switch
(Channel 5) on switch B. The Panic button is on the I button
(Channel 6). SAFE airplanes have a xed conguration in the
receiver and will match this setup after binding.
• The SAFE Select template uses the D switch for aps (Channel
5), the A switch for retracts (Channel 6), and the B button
to turn SAFE select ON or OFF (Channel 7). Selecting this
template alone will not enable SAFE Select, it must be done
during the bind process. Also, the switch must be assigned in
the receiver after binding, and the ap travel values need to be
applied. See your airplane manual for more information.
3. If you select Cancel, the system will return to the Model
Select function.
4. If you select Create, the new model will be created and now
be available in the model select list.
WARNING: Complete a preight check before
attempting to y any model with a new model le or
template. If you have the controls set up incorrectly for your
aircraft, it may result in loss of control and a crash.
Create New Model

19SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
Use the Model Reset menu to delete all model programming in
the active model memory. Reset returns all model settings to the
default settings and erases all programming in the selected model.
After a model reset, it is necessary to re-bind.
With this function you can sort the model order in the model select
function. This is helpful to group similar models together to make
them easy to nd. To move a model, highlight the model that you
wish to move with the scroll wheel, then press the scroll wheel to
select it. Scroll the scroll wheel to move the selected model to the
position desired. Press the scroll wheel when you have the model
in the position desired.
Run this option to verify your model les are valid. If there are any
corrupted model les this process can detect them.
This option will delete all model les. Only run this option if you
want to remove all models les, they cannot be recovered once
this option has been executed.
The Warnings menu enables you to program a voice, tone or
vibration alert during power on of the transmitter for any selected
switch or channel position.
The alarm activates and an alert message appears on the screen if
a specic switch or control stick is in an unsafe position when you
power the transmitter on.
Return the switch or control stick to the safe position to silence the
alarm.
For safety reasons, the default throttle alarm activates if the
throttle position is above 10%.
SYSTEM SETUP
Warnings
Sort Model List
Validate All Models
Delete All Models
Model Reset

20 SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL
EN
TELEMETRY
Installing the optional telemetry module and sensors enables the
display of aircraft performance data on the transmitter screen.
You can also enable Data Logging to save a telemetry le on the
Memory card and view the data in the Spektrum STiTM mobile
application or other TLM le viewers.
Display
Telemetry display options include:
Tele: When you press the scroll wheel, the Telemetry screens
appear and the Main Screen is disabled.
Main: Telemetry alerts appear on the Main screen, but all
Telemetry screens are disabled.
Roller (Default): Allows you to toggle between the Telemetry
screens and the main screen by pressing the
scroll wheel.
Auto: The Telemetry screen automatically appears as soon as
the transmitter receives data from the telemetry module.
Units
Scroll to Units and press the scroll wheel to change between US
and Metric.
IMPORTANT: The Auto-Cong option is not available from the
System Setup>Telemetry menu. RF signal must be transmitting
when you use the Auto-Cong option. When the System Setup
menu is active, RF signal is off.
The NX6 transmitter features telemetry Auto-Conguration,
allowing the transmitter to detect new telemetry sensors.
To use Telemetry Auto-Config:
1. Make sure all telemetry components are bound to the
transmitter and receiver.
2. Power on the transmitter, then power on the receiver.
3. Select Telemetry from the Function List, then select Auto
Cong. “Conguring” ashes for 5 seconds and any new
sensors appear in the list.
4. Adjust the sensor alert values as necessary.
Status Reports:
Status Reports determines how often the transmitter refreshes
the data on the screen. Each telemetry sensor can be adjusted
independently.
For example, the RPM status report can refresh every 10 seconds
while the altimeter sensor refreshes every 15 seconds.
Warning Reports:
Warning Reports determines how often a telemetry alert occurs,
if an alert is active.
SYSTEM SETUP
Telemetry Settings
Telemetry Auto-Configuration
Select Inh under Alarm to select the type of alarm desired.
Options include Inh and Tone.
File Settings
This is used to select the data logging settings.
File Name
1. Select File Name to assign a custom le name.
2. The File Name screen appears, allowing you to name the le
as you would for a Model Name or Flight Mode Name. The le
name can include a maximum of 8 characters.
3. Press BACK to save the name.
Start
1. Select Start to assign a specic switch position or stick
position that activates Data Logging.
2. Press the scroll wheel once to save the selection.
Enabled
When Enabled is set to NO, Data Logging is turned off.
Select YES to save Telemetry data to the Memory card. The
Memory card must be installed in the transmitter to select YES.
CAUTION: If you access the Telemetry menu from the
Function List, you may see a Frame Loss appear when
you exit the menu. The Frame Loss is not an error, but there will
be a momentary loss of radio signal when exiting the Telemetry
screen. DO NOT access the Telemetry menu during ight.
Telemetry Alarms