Split Phantom ULB21-DLP Quick guide

PLIT450 REV. B 8/26/11
INSTALLATION AND INSTRUCTION MANUAL
IMPORTANT: Please read all of the following instructions before installing your new warning light.
The Split Phantom
The Split Phantom
™
Under over Interior LED Split Lightbar
With Generation-4 LED
Takedown and Dire tional Pursuit Lights
Models
ULB21-DLP ULB24-DLP
(Discrete) (Gen 4 Starburst)

-1-
The Split Phantom ™ uses state-of-the-art Light Emitting Diode (LED)
technology. This warning light is comprised of ultra-high intensity LEDs that
are operated by a micro-controller to efficiently produce light output with
lifetimes up to 1 , hours.
IMPORTANT: Please read all of the following instructions before installing your new
Split Phantom ™ LED undercover lightbar.
CAUTION: Please be sure to check that your cigarette plug outlet is properly fused. Testing the
light before this fuse is properly installed will void the warranty on the light.
WARNING!!!! Care should be taken when positioning this warning light so that the light and/or
cord does not interfere with the proper operation of the driver-side or passenger-
side airbag! Failure to heed this warning may result in serious or fatal injury.
Please Note: These instru tions are provided as a general guideline only. Spe ifi
mounting and/or wiring, may be ne essary and are the sole responsibility of the
installer. Star Headlight & Lantern Co., In . assumes no responsibility for the
integrity of the installation for this or any of its produ ts.
CAUTION: All of our DC powered warning lights are polarity
sensitive. These lights are polarity protected only if the
appropriate fuse is used. All wires connected to the positive
terminal of the battery should be fused at the battery for their
rated load. Testing the light before this fuse is properly
installed will void the warranty on the light.
NOTICE
Due to continuous product improvements, we must reserve the right to change any
specifications and information, contained in this manual at any time without notice. Star
Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual,
including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use of
this manual.

-2-
274-ULB21-U1
Universal Mountin Kit
274-ULB21-CH11
2011 Dod e Char er Mountin Kit
274-ULB21-CV
2006-2011 Ford Crown Victoria Mountin Kit
2009 Ford F150 & F250
274-ULB21-EX
2006-2010 Ford Explorer Mountin Kit
2007-2010 Ford Expedition Mountin Kit
274-ULB21-IM
2008-2010 Chevrolet Impala Mountin Kit
274-ULB21-TA
2007-2011 Chevrolet Tahoe Mountin Kit
2007-2011 Chevrolet Yukon Mountin Kit
2007-2011 Chevrolet Suburban Mountin Kit
274-ULB21-CH
2006-2010 Dod e Char er Mountin Kit
2007-2008 Dod e Ma num Mountin Kit
2009 Dod e Ram Mountin Kit
Optional Mountin Brackets
There are seven (7) optional mounting brackets that can be used to mount your
Split Phantom ™ or Half Phantom ™. Your light comes with the one that was
selected at the time the light was ordered. Please review the diagram below
that shows the parts included with each kit.
Please Note: very ULB21 comes with a standard baffle included. The 274-ULB21-CH
and 274-ULB21-CH11 kits also include a separate baffle that is specifically designed to
fit the Dodge Charger. It should be used in place of the standard baffle included.

-3-
The Split Phantom ™ is desi ned to be mounted on the inside
of your vehicle. It is not intended for exterior applications and is
not warranted a ainst water dama e.
It is the sole responsibility of the owner to ensure the warning light is
secure. Check your light every time you enter the vehicle to ensure that
it is mounted securely. The manufacturer assumes no responsibility for
the secure mounting of this light.
The following mounting instructions describe the standard, most
common way to mount this light. This method may or may not apply to
your vehicle. Because vehicles can vary widely in their design, it may be
necessary to configure the brackets differently than described. Some
applications may require you to design your own custom brackets. The
installer assumes all responsibility for the integrity of the installation. It is
the sole responsibility of the owner to ensure the li ht is secure.
Mountin Instructions
Before installing any of the
brackets, slide the enclosed
rubber channel over the
front edge of the baffle .
The ULB21 is designed to be mounted in the front windshield of a vehicle using
both of the pre-existing visor clips. An alternate method is also shown using the
Universal Brackets.

-4-
SUCTION CUP
OR
WINDOW ADHESIVE
MOUNT
UNIVERSAL BRACKET INSTALLATION
(Model 274-ULB21-U1)
• The Universal Mount use two forked brackets and either a pair of suction
cups or a pair of window adhesive mounting pads (both included).
• The Forked Brackets must be installed for both the suction cup and
window adhesive mounts.
• Determine if you can install the Forked Brackets under your visor clips or
if you need to attach them in an alternate fashion and refer to the
appropriate section on pages 6 or 7.
The mountin instructions are divided into two separate sections. If you
are usin the Universal Mount, proceed below. If you will be usin one of
the vehicle specific brackets, please skip to pa e 9.

-5-
CAUTION: Take extreme caution not to over ti hten the screws!!! Over
ti htenin of the screws can strip the holes.
1. Insert one of the carriage
bolts through one of the
washers. Please note that
washer is used as a spacer
on the square neck of the
carriage bolt. Slide the bolt
and washer through the
back of the left bracket.
Be sure to select the correct
bracket. The larger flange
should be located towards
the center of the light.
2. Remove three of the #8 x 1/2" self-
tapping Phillips pan head screws and
use them to install the left attaching
bracket on the light.
CAUTION: Take extreme caution not
to over ti hten the screws!!! Over
ti htenin of the screws can strip the
holes and result in a faulty mount.
3. Once the left attaching bracket is installed
securely on the light, fasten one of the
forked “L” brackets to the attaching
bracket, using the carriage bolt,
a washer, and a nut. Leave
the nut slightly loose to
allow for minor adjustments
during the remainder of the
installation.
Attach Forked Brackets to Li ht
4. Repeat steps 1-3 for the right attaching bracket .
Universal Mountin (CONT'D)

-6-
1. Standard mounting uses the factory
installed visor clips already located on
the vehicle, in conjunction with the
suction cups or window adhesive
mounts. If you do not have any visor
clips, use the Alternate Mountin
section on the next page .
2. Locate the two visor clips on the vehicle.
The style may vary from vehicle to vehicle.
Some styles use only one screw each,
while others may have more. Verify that
both visor clips are a minimum of 3” from
the center of the window, and a maximum
of 8” from the center.
3. Loosen (or remove if necessary) both visor
clips enough that one of the forked brackets
can easily slide under each of them.
4. Slide one forked bracket under each visor clip
and tighten the clip such that it securely holds
each bracket in place.
Bend here if
necessary
5. Once the brackets are installed securely under the visor clips or with a suitable
fastener, check to see that the bottom of the light is level front-to-back. If it is
not level, remove the light from the visor clips and carefully bend the forked
brackets as necessary. Reinstall the light and check again for levelness.
Repeat this process until the light is level.
Attach Forked Brackets to Visor Clips
(If you do not have visor clips, or your visor clips will NOT provide a secure mount, or this
method will not work in your vehicle for any other reason, use the alternate method on the
next page.)
Universal Mountin (CONT'D)

-7-
Attach Forked Brackets usin Alternate Method
If you are not using the visor clip installation described on the previous page,
continue below.
1. Some vehicles may not have visor clips appropriate for the previously
described installation, or may completely lack any visor clips. An alternate
mounting screw hole is provided in the bracket for these situations. This hole
can be used with an appropriate user supplied screw or other suitable fastener.
2. If you are using the alternate mounting screw hole, you will need to locate the roof
brace under the headliner of the vehicle.
3. Once you have located the roof brace, pick an area to mount the brackets (one on
each side) that is a minimum of 3” from the center of your window and a maximum
of 8”.
4. You must then determine an appropriate size screw to penetrate the headliner and
securely mount the brackets to the roof brace. When selecting a screw, take care to
ensure that it is capable of supporting the weight of the light and it will not penetrate
the roof of the vehicle.
5. Carefully drill any necessary pilot holes in your roof brace. CAUTION: Take care to
ensure when selectin a screw and drillin the hole that it is capable of
supportin the wei ht of the li ht and that it does not penetrate the roof of the
vehicle.
6. Install the screws through each bracket.
7. If necessary, adjust your light as described in Step 5 on the previous page.
Alternate
Mounting
Hole
Universal Mountin (CONT'D)

-8-
Universal Mountin (CONT'D)
2. Use the screws to attach the
"L"-Brackets to either end of
the light as pictured to the
right. You may desire to
remove the nylon spacer if
the screw does not securely
fasten to the base.
CAUTION: Take extreme
caution not to over ti hten the
screws!!! Over ti htenin of
the screws can strip the holes
and result in a faulty mount.
or
Remove outermost s rews
from bottom of unit.
(Bottom View)
Attach The Suction Cups or Window Adhesive Mounts
1. Remove the two #4 x 1/4" Phillips pan head screws on either end of the bar,
along with the washers and nylon spacers.
3. Then use the appropriate hardware (as shown above) to attach either the
Adhesive Pads or the Suction Cups, depending upon your application.
If using the window adhesive:
• Be sure to use the tube of cleaner to clean both surfaces.
• After applying adhesive, please allow a minimum of 2-5 minutes
for the pad to adhere to the window before releasing pressure.
• Allow 24 hours for the adhesive to fully cure before using.
4. Continue to the BAFFLE ADJUSTMENT section on page 11.

-9-
1. Remove both the driver and
passenger visor clips from
the vehicle.
3. Slide the forked end of the visor
bracket under the visor pivot arm
that you just loosened.
(Passenger’s side shown)
2. Loosen (LOOSEN, DO NOT REMOVE!!)
the three visor pivot arm screws on one
side of the vehicle with appropriate
screwdriver. (Passenger’s side shown)
4. Align the square hole on the other
end of the visor bracket with the visor
clip hole. (Passenger’s side shown)
VEHICLE SPECIFIC BRACKET INSTALLATION
(Models 274-ULB21-CH, 274-ULB21-CV, 274-ULB21-EX,
274-ULB21-IM, and 274-ULB21-TA)
6. Tighten the screws on the visor arm
to hold the visor bracket in place.
(Passenger’s side shown)
5. Replace and tighten visor clip to
secure the visor bracket to your
vehicle. (Passenger’s side shown)
Note: Bracket styles can vary with
some not needin the additional “L”
bracket shown in step 9.

-10-
9. If you have a separate
angled "L" bracket, place it
over the two studs on the
visor bracket as shown to
the left. Using two #8
washers and two acorn
nuts, attach the “L” bracket
to the threaded studs.
Note: You may want to
leave the acorn nuts
slightly loose to allow for
easier final adjustments.
(Passenger’s side shown)
1 . Attach the light to the "L"
bracket using the two stud
brackets that you mounted on
the lights in Step 8. Secure
the light using two #8 washers
and acorn nuts as shown to
the right. Note: You may want
to leave the acorn nuts slightly
loose to allow for easier final
adjustments.
4. Align the square hole on the other
end of the visor bracket with the visor
clip hole. (Passenger’s side shown)
11. Loosen the two Baffle
Adjustment Screws located on
the bottom of the light to allow
the baffle to slide. (Driver’s side
shown)
Vehicle Specific Mountin Brackets (CONT'D)
7. Remove the two pairs of screws from
each light half as shown to the right.
8. Install a stud bracket
at each location
using the same
screws to secure
each bracket. The
tabs on each stud bracket should
point AWAY from the cable joining
the two halves.

-11-
CAUTION: Take extreme caution not to over ti hten the
screws!!! Over ti htenin of the screws can strip the holes.
3. Once all of the brackets are securely tightened, check your mount to ensure the
desired angle is achieved. Stand in front of the vehicle and inspect the light
through the front windshield. The screws may be loosened slightly to allow for any
final adjustments necessary.
4. After all the necessary adjustments are made retighten all the screws.
CAUTION: Take extreme caution not to over ti hten the screws!!! Over
ti htenin of the screws can strip the holes and result in a
faulty mount. .
Star Headlight & Lantern Co., Inc. assumes no
responsibility for the secure mounting of this light. It is the
responsibility of the installer and/or owner to ensure the
lightbar is mounted securely. Check your light every time
you enter the vehicle to ensure that it is mounted securely.
CAUTION!!! Once the li ht is secured, route your cord such that
it does not interfere with the vision of the driver or the operation
of the steerin wheel, ear shifter, and/or any airba s.
1. After the top of the light is
touching the windshield, slide
the baffle forward until it
satisfactorily blocks any
reflected light.
2. Tighten the Baffle Adjusting
Screws to secure the baffle
in place .
Vehicle Specific Mountin Brackets (CONT'D)
BAFFLE ADJUSTMENT (All Models)
12. For models that have the
separate “L” brackets, with
the acorn nuts still slightly
loose, slide the light as close
to the front windshield as
possible. Once it is touching
the window, tighten the two
acorn nuts that secure the
two brackets together.
13. Repeat Steps 2-12 for the
opposite side of the vehicle.

-12-
Wirin
For proper installation and full operability, this light requires a 10.5A ignition
swit hed power sour e, onne tions to the negative terminal of the battery,
and four external swit hes rated for a minimum 1A (user supplied).
These lights come with a pre-installed 6-conductor harness. In addition, the cable
also contains a bare drain wire and foil shielding.
+ -
BLACK
BARE
Orange w/Red Flashing Warning Lights
Steady Burn Warning Lights
Green w/Red
White w/Brown Pursuit Lights (Flashing DLP)
Green w/Yellow Takedown Lights (Steady Burn DLP)
Warning Lights
DLP
Lights
Ignition Switched +12VDC
Red
User Supplied Switches
1 AMP
FUSE
Wire Function
Bare Ground
Black Ground
Red Power to light (+12VDC ignition switched – 1 .5A)
Orange w/Red Warning LED Flashing Mode
Green w/Red Warning LED Steady Burn (and Burst)
White w/Brown DLP LED Pursuit Mode
Green w/Yellow DLP LED Takedown Mode (Steady Burn)
Quick Wirin Guide
All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load. Testing the light before this fuse is properly
installed will void the warranty on the light.

-13-
Detailed Wirin Descriptions
Bla k: (Ground) Connect the Black wire to the negative side of the battery
(preferred) or a good chassis ground. This wire provides the
ground for the operation of the light.
Bare: (Ground) Connect the bare wire to the negative side of the battery
(preferred) or to a good chassis ground. This wire helps
reduce RFI.
Red: (Ignition switched +12VDC) - POWER
The Red wire provides the power to your light. It does not activate any functions,
but you must have +12VDC applied to it for any of the functions to work.
Connect the red wire throu h a 10A fuse to a source capable of deliverin
at least 10.5 amps.
Please Note: When the red wire is connected to +12VDC the light will draw a
small current (5 mA). Occasionally vehicles may sit for extended periods of time
(i.e. more than a few days), thus we recommend that the red wire be routed
through an ignition switched power source.
Orange w/Red: (Switched +12 VDC) - WARNING
When +12VDC is applied to the Orange w/Red wire, the
Warning LEDs will activate, displaying the pattern that was
selected when the unit was previously powered off.
Green w/Red: (Switched +12 VDC) - ALL TAKEDOWN
When +12VDC is applied to the Green w/Red wire, the Warning
LEDs will activate in Takedown Mode (steady burn). This mode
will override the flashing LED mode above, if both the Orange
w/Red and Green w/Red wires have +12VDC applied to them.
White w/Brown: (Switched +12 VDC) - PURSUIT
When +12VDC is applied to the White w/Brown wire, the DLP
li hts will activate in Pursuit Mode (alternately flashing).
Green w/Yellow: (Switched +12 VDC) - DLP TAKEDOWN
When +12VDC is applied to the Green w/Yellow wire, the DLP
li hts will activate in Takedown Mode (steady burn). This mode
will override the flashing LED mode above, if both the White w/
Brown and Green w/Yellow wires have +12VDC applied to
them.
Warning Lights
DLP
Lights

-14-
Operatin Instructions
All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load. Testing the light before this fuse is properly
installed will void the warranty on the light.
Main control of this light is done though four of the wires in the harness. They
should be connected to +12VDC through 4 switches (user supplied) as described
in the Wirin section.
Applying power to the appropriate wire elicits the functions described below.
LED Flashing Mode (Orange w/Red)
The Warning LEDs will flash according to the pattern you have selected (See
Pattern Select/Burst Mode Button section on next page).
All LED Steady Burn Mode (Green w/Red)
The Warning LEDs will not flash, but instead will remain lit, similar to Takedown
lights.
DLP Pursuit Mode (White w/Brown)
The LED DLP lights will flash, alternating back and forth at the speed you had
selected when this function was last deactivated (See Pattern Selection
section on next page).
DLP Takedown Mode (Green w/Yellow)
The LED DLP lights will not flash, but instead will remain lit.
Located on the bottom of The Star Phantom
®
, is an Indicator LED. When your light
is activated in any mode, this LED will flash to alert you to the lightbar activity in the
daylight.
Active Mode Indicator LED Display
Warning LED Flashing Mode Fast Flash
DLP LED Flashing Mode Slow Flash (overrides Fast Flash)
Warning LED Steady Burn or
DLP Takedown (Steady Burn) Steady (overrides Fast or Slow Flash)
Warning LED Burst Mode Flicker (overrides Steady, Fast or Slow Flash)
Indicator LED
Warning Lights
DLP
Lights

-15-
Pattern Select/Burst Mode Button
The button on the right half of the light is the Pattern Select/Burst Mode button. This is
a momentary switch and has four different functions, depending upon which mode the
light is in (i.e. which wire is activated).
Operation (CONT'D)
Please note that this button will only function properly if ONLY
the sin le wire indicated has +12VDC applied to it. If multiple
functions are activated, the Indicator LED will flash four (4) quick
times, indicatin an error.
Warnin LEDs in Flashin Mode (Only Oran e w/Red wire activated):
If the Star Phantom
®
is in Flashing Mode, the Pattern Select/Burst Mode button
will act as the Pattern Select button. Each time this switch-button is depressed,
The Star Phantom
®
will cycle to the next pattern. The Star Phantom
®
is
designed with thirty-five different patterns (see next page).
Warnin LEDs in Steady Burn (Takedown) Mode ( Only Green w/Red wire activated ):
If the Star Phantom
®
is in the Steady Burn Mode, the Pattern Select/Burst Mode
will “burst” your LEDs into a super-bright, high-power mode (takedowns). This
mode will activate for approximately 3 seconds then revert to the standard steady
burn mode. Please Note: Immediately after the 3 second “Burst Mode” has
ended, the light will be “locked out” of Burst Mode for 3 seconds.
DLP LEDs activated in Pursuit (flashin ) Mode:
If only the Red and White w/Brown wires have +12VDC applied to them, the DLP
lights will be in Pursuit Mode (alternating back and forth). The Pattern Select/Burst
Mode button will allow you to select which speed you would like these lights to
alternate at 1.6FPS or 2.4FPS. Each time this switch-button is depressed and
released, the DLP lights will change speed. Note: The indicator L D will
momentarily go off while the button is pressed in.
DLP LEDs in Steady Burn (Takedown) Mode ( Only Green w/Yellow wire activated ):
If the Star Phantom
®
DLP LEDs are in the Steady Burn Mode, the Pattern
Select/Burst Mode button will “burst” them into a super-bright, high-power mode
(takedowns). This mode will activate for approximately 3 seconds then revert to
the standard steady burn mode. Please Note: Immediately after the 3 second
“Burst Mode” has ended, the light will be “locked out” of Burst Mode for 3 seconds.
Pattern Sele t / Burst Mode

-16-
Pattern List
1 Slow Warn *
2 Fast Warn
3 Superfast Warn
4 Warn Fade
5 Pre-Pop Warn
6 All Singleflash
7 Alt. Tripleflash
8 All Tripleflash
9 Alt. Quadflash w/Post Pop
1 All Quadflash w/Post Pop
11 Alt. Quintflash
12 All Quintflash
13 Alt. Pre-pop Quintflash
14 All Flicker
15 Alt. PSU Flicker
16 One Side Pop, Other Side Rapid Fire
17 One Side Rapid Fire, Other Pop
18 Comet 1
19 Comet 2
2 Delta Omega (Flash Rate Sweep)
21 Slow Warn, Superfast Warn
22 All Singleflash, All Flicker
23 Alt. Double, ALT. Quad w/Post Pop
24 All Double, ALL. Quad w/Post Pop
25 Alt Double, Alt. Pre-Pop Quad, Alt. Quad w/Post Pop, Alt Flicker
26 All Double, All Quintflash, All Quadflash w/Post Pop, All Flicker
27 All Quadflash w/Post Pop, All Doubleflash, All Flicker
28 Alt. Pre-Pop Triple, Alt. Doubleflash, Alt Flicker **
29 Alt. Pre-Pops, Alt. Flicker, Superfast Warn
3 Delta Omega, All. Double, All. Flicker
31 One Side Steady---Other side Singleflash †
32 One Side Steady---Other Side Short-Long †
33 Warn Medium (Alt. Long Singleflash) †
34 Alt. Short - Alt. Long †
35 Cycle All
† = These Patterns meet California Title 13 and SA J595 specifications in Red and Blue versions of the
model ULB42 only. (ULB42V models DO NOT meet these specs)
* Default Pattern #1
** Default Pattern #2
• If at anytime you would like to go directly to the Slow Warn (pattern #1), simply
press, and hold the pattern select button for approximately 3 seconds. When the
LEDs flash once, release the button and the light will be in the Slow Warn
pattern.
• If you would like to place the light back into the default pattern (Pattern 28: Alt.
Pre-Pop Triple, Alt. Doubleflash, Alt Flicker), simply press and hold the pattern
select button until the LED’s flash twice (approx. 6 seconds). Then release the
button and the light should be in the default pattern.
• To le Mode: Pressing and holding the pattern select button until the LED’s
flash three times (approx. 9 seconds) will toggle the “steady side” for patterns 31
and 32.
• Indicator LED: Pressing and holding the pattern select button until the LED’s
flash four times (approx. 12 seconds) will disable or enable the indicator LED.
• The Split Phantom will remember the pattern it was in when turned off and
display the same pattern when re-activated.

-17-
Once your Split Phantom ™ is installed, please test all the patterns
and options to familiarize yourself with the various patterns and the
operation of the buttons.
If you have any questions concerning this or any other product, please
contact our Customer Servi e Department at [phone].

-18-
These lights use state-of-the-art Light Emitting Diode (LED) technology. These warning lights are
comprised of ultra-high intensity LEDs that are controlled by a solid state flasher unit to efficiently
produce light output with lifetimes up to 1 , hours. Under normal circumstances, you will not
need to replace any LEDs in this light. If any of the LED's in your light do fail, please contact Star
Headlight for arrangements to have them repaired. The flasher unit and heads CANNOT be
serviced in the field and any attempt to do so will void the warranty.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and
workmanship for five years after the date of purchase. The owner will be responsible for
returning to the Service Center any defective item(s with the transportation costs
prepaid. The manufacturer will, without charge, repair or replace at its option,
products, or part(s , which its inspection determines to be defective. Repaired or
replacement item(s will be returned to the purchaser with transportation costs prepaid
from the service point. A copy of the purchaser's receipt must be returned with the
defective item(s in order to qualify for the warranty coverage. Exclusions from this
warranty include, but are not limited to, domes, and/or the finish. This warranty shall not
apply to any light, which has been altered, such that in the manufacturer's judgment,
the performance or reliability has been affected, or if any damage has resulted from
abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability
or fitness , which extend this warranty period. The loss of use of the product, loss of time,
inconvenience, commercial loss or consequential damages, including costs of any
labor, are not covered. The manufacturer reserves the right to change the design of
the product without assuming any obligation to modify any product previously
manufactured.
This warranty gives you specific legal rights. You might also have additional rights that
may vary from state to state. Some states do not allow limitations on how long an
implied warranty lasts. Some states do not allow the exclusion or limitation of incidental
or consequential damages. Therefore, the above limitation(s or exclusion(s may not
apply to you.
NOTE: Most failures can be traced to wiring and battery problems. Check
"quick-connects” and wiring to insure that correct voltage/polarity is
reaching the electronic strobe light/LED beacon.
If you have any questions concerning this or any other product, please contact our
Customer Servi e Department at [phone].
If a product must be returned for any reason, please contact our
Customer Service Department to obtain a Returned Materials Authorization
number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.