S+S Regeltechnik Rymaskon 200-Modbus Series User manual

Table of Content
1.1. Overview..............................................................................................................4
1.2. Key Features........................................................................................................5
1.3. LCD Segments.....................................................................................................6
2.1. Hardware Installation.......................................................................................10
2.2. User Interface....................................................................................................11
2.2.1. General Description.................................................................................11
2.2.2 Operating Modes .....................................................................................12
2.2.3 Access Levels ..........................................................................................14
2.2.4 Device Settings ..........................................................................................15
2.2.5 Factory Default........................................................................................16
3.1. Introduction.......................................................................................................17
3.2. Modbus Network...............................................................................................17
3.3. Modbus Register Usage for Value Display......................................................18
3.4. Modbusregister Description.............................................................................19
3.4.1 Data Registers..........................................................................................19
3.4.2 Device Settings ........................................................................................27
3.4.3 Configuration Registers...........................................................................29
3.4.4 Model Information Registers (read only).................................................46
3.4.5 Device Information Registers (read only)................................................47
3.4.6 NFC Registers...........................................................................................48
3.4.7 Value Scaling and Stepwidth...................................................................49
5.1. General Description..........................................................................................51
5.2. Remote Control Pairing....................................................................................52
6.1. Technical Support.............................................................................................53
7.1. Physical Specifications......................................................................................54
7.2. Sensor Specifications.........................................................................................55




























Table 1: Key Features
Table 2: Possible Order Codes

Figure 1: LCD Segments available on RYMASKON 200 displays











































Table 3: LCD Segments Overview

Figure 2: Back View RYMASKON 200

Figure 3: Front View RYMASKON 200
change set point or device setting in EDIT-mode
directly access a set point in DISPLAY-mode
no specific function, the button state can be requested to control lighting
no specific function, the button state can be requested to set occupancy
state
short press <3s: cycle through display values, set points or device
settings
long press ~3s: switch between DISPLAY-mode and EDIT-mode
long press >6s: switch to CLEANING-mode




Figure 4: RYMASKON 200 Operating Modes

Table 4: Operating Modes
Display values are shown.
Set points are shown.
Set points can be edited.
Device settings can be edited. This mode is only accessible for
the system admi-nistrator.
Offset values can be edited
The pincode for the end user has to be entered to show and/or
edit the requested value.
The pincode for the system administator has to be entered to
show and/or edit the requested value.
A defined set point can be accessed and edited without
entering EDIT-mode. It can be entered by pressing a defined
button (see Table 23 on page 31). In contrast to EDIT-mode
only predefined set points can be edited.
The DIRECT_ACCESS-mode can be left by pressing any
button that has no direct access capability.
This mode is used to clean the surface of the device without
any response of the touch buttons and hence any unwanted
changes. This mode is entered by pressing the MENU-button
for at least 6 seconds. After 10 seconds with no interaction the
device will switch back to DISPLAY-mode automatically.

Figure 5: Pincode Entry

Modbus Parity
Odd / Even / None
Modbus Baudrate
1.2kB / 2.4kB / 4.8kB / 9.6kB / 19.2kB /
38.4kB / 57.6kB / 115.2kB
Modbus Address
1 - 247
Pincode System Administrator
0000 –9999
(if 0000 the pincode is disabled)
Pincode End User
0000 –9999
(if 0000 the pincode is disabled)
Color Setting LCD Backlight Red
0% - 100%
Color Setting LCD Backlight Green
0% - 100%
Color Setting LCD Backlight Blue
0% - 100%
Brightness LCD Backlight
0% - 100%
LCD Contrast
0% - 100%
LCD Color Scheme
0 –user (as defined above)
1 –white
2 –red
3 –green
4 –blue
5 –orange
6 –magenta
7 –cyan
Time Format
24h / 12h
Show Date
on / off
Show Time
on / off
Acoustic Feedback (for Touch Buttons)
on / off
Goto First Display Value (the first
display value will be displayed after 1
minute without inter-action)
on / off
Display Auto Shuffle
on / off
Display Auto Dim
(lcd brightness will be dimmed after 2
minutes with no interaction)
off / 50% / 10% / 0%
Unit System
SI / US
Device Restart
off –if a DOWN-button is pressed the
device will be rebooted manually
Table 5: Device settings

Internal Temperature
Relative Humidity
Dew Point
External Temperature
Internal Temperature Set Point
Fan Stage
Table 6: Factory Default for RYMASKON 200

Figure 6: Modbus Network

Figure 7: Modbus Register Usage for Value Display

Table 7: Button States and Flags

Table 8: Change Flags
Table 9: IR Remote Control Command