Sport-thieme 114 5410 User manual

Assembly instructions
Product codes: 114 5537
& 114 5410
Sport-Thieme
Aluminium Reel Trolley
Thank you for choosing a Sport-Thieme product!
Please read the instructions carefully before use so you can enjoy this product safely.
If you have any questions, our team is here for you.
Version 02/2020 | Page 1
Product code 114 5537:
Sport-Thieme®
aluminium reel trolley
Product code 114 5410:
Sport-Thieme®
aluminium reel

Assembly instructions
For product codes 114 5537 & 114 5410
Page 2
1. Items included
Please check that all parts listed below are present before starting assembly.
Trolley Reel
Qty Description Qty Description
2
Side section
2
Wheel
1
Crossbar
1
Tube
1
Handlebar
1
Accessory pack
1
Accessory pack
Trolley accessory pack Reel accessory pack
Qty Description Qty Description
2
Castor, grey, 75×25 mm
2
Plastic cap, grey, 1½ inches
4 Square plastic cap, grey, 30×30 mm 2 Ring eyelet screw, M8×30
2
Round plastic cap, grey, dia. 30 mm
2
Nut, M8, DIN 934
4 Hex-head screw, M6×65, DIN 933 2
Toothed lock washer, dia. 8.4 mm,
DIN 6797
2
Hex-head screw, M6×45, DIN 933
1
Assembly instructions
2
Hex-head screw, M8×45, DIN 933
6
Lock nut, M6, DIN 985
2
Serrated lock washer, dia. 8.4 mm,
DIN 6798
1
Assembly instructions

Assembly instructions
For product codes 114 5537 & 114 5410
Page 3
2. General
We recommend assembling the parts on a smooth surface to prevent the items from becoming scratched!
Preparation
Remove the packaging and lay out all parts.
You will need the following tools for assembly:
•1 hammer or rubber mallet
•2 spanners, 10 mm
•1 spanner, 13 mm
3. Trolley assembly
A) Castors
Attach the two castors (75×25 mm) to the relevant bracket on each side section using one M6×45 DIN 933 hex-
head screw and one M6 DIN 985 lock nut each. Only tighten the nut so it sits flush with the outer edge of the hex-
head screw and so the castor can still rotate freely (see photos below).
B) Crossbar and side sections
To connect the two side sections, position the round crossbar (dia. 30 mm) between them, and place a serrated
lock washer (dia. 8.4 mm) onto each of the M8×45 DIN 933 hex-head screws. Then insert the screws into the
thread of the crossbar, pushing them through the hole in each side section. Tighten firmly (see photos below).

Assembly instructions
For product codes 114 5537 & 114 5410
Page 4
C) Plastic caps
Attach the two round plastic caps (dia. 30 mm) to the handlebar ends and the four square plastic caps (30×30 mm)
to the relevant side section ends using a hammer or rubber mallet.
D) Handlebar
Place the handlebar so its holes align with the holes on the side sections. Attach the handlebar to the side sections
using the M6×65 DIN 933 hex-head screws provided (two on each side), inserting them from the outside of the
handlebar, and secure each one with an M6 DIN 985 lock nut on the inside of the side sections. The handlebar
must be on the opposite side of the castors.

Assembly instructions
For product codes 114 5537 & 114 5410
Page 5
4. Reel assembly
Insert the tube (dia. 50 mm) into the hub of each wheel and align the holes of the tube with those of the wheels
(see the first image below, on the left). Fit each of the two ring eyelet screws (M8×30) with an M8 DIN 934 nut –
screwing this to the end of the thread – and a toothed lock washer (dia. 8.4 mm, DIN 6797), and then insert through
the threaded hole on the tube and tighten.
Fit each hub with a 1½-inch-diameter plastic cap using a hammer or rubber mallet.

Assembly instructions
For product codes 114 5537 & 114 5410
Page 6
5. Maintenance, care, safety and storage
Regularly tighten all screws on the reel and trolley. Check all parts for any damage and replace if
worn.
Please note
Due to continuous quality control of our products, technical changes may occur.
Make sure that the trolley is placed on a level surface when used and/or stored to prevent it from rolling away.
Permanent contact with water can cause surface changes to the aluminium and may damage the components
(which are made of other materials). Additives in the water in swimming pools can also affect the surface/materials.
We recommend rinsing the product with clean water after each use and then carefully drying it with a soft cloth.
If you have any questions, our experts at Sport-Thieme are here for you.
Haspo Sportgeräte GmbH & Co. KG owns the copyright to the illustrations and text contained herein. Use is not
permitted, and only allowed after prior agreement.