Sport-thieme 122 4001 User manual

Sport-Thieme GmbH
38367 Grasleben
/ Germany
Tel: [phone]
Fax: [phone]
Operating/assembly instructions
Swivel castor kit for vaulting boxes
Prod. code: 122 4001
page 1 / 4
04/2016
!
! !
Assembly instructions for swivel castor kit
Thank you very much for choosing a product. Please read the instructions
fully before you assemble the equipment so you can enjoy the product and its
guaranteed safety:
measured from
the floor!
Ill. 1: Sport-Thieme swivel castor kit for vaulting boxes
Included:
Pos. Description
1 front set of castors with telescopic lever
2 rear set of castors without telescopic lever
3 adjustable connecting tube
4 4 x axle bearing
5 8 x coach bolt M8 with locking nut
6 2 x telescopic lever
7 2 x hex bolt M8 with locking nut
For!castors!
1000!mm!
From!
the!
floor!

Sport-Thieme GmbH
38367 Grasleben
/ Germany
Tel: [phone]
Fax: [phone]
Operating/assembly instructions
Swivel castor kit for vaulting boxes
Prod. code: 122 4001
page 2 / 4
04/2016
!
! !
Tools required:
2 spanners 13 mm
1 wood drill bit ∅ 8.5 mm !!!!!*!
1 jigsaw *
measured from
the floor!
Order of assembly
1. *If the box is not already prepared, mark 8 holes ∅8.5 mm on the side
of the box’s bottom section as shown and drill.
2. *After that, the cut-out in the front is marked as shown in view A and cut.
3. Insert the axle bearings!into the tube ends of the two sets of castors"and #.
4. Place the sets of castors"and #together with the axle bearings!into the
box’s bottom section. Insert the telescopic lever$into the respective cut-out.
5. Using the 8 coach bolts%bolt the sets of castors"and #to the box
section.
6. Bolt the adjustable connecting tube&to the top of the set of
castors"using hex bolts and locking nuts'.
7. Turn the threaded part of the connecting tube&by so much that, when the
telescopic lever$is engaged, the castors lift the vaulting box safely and
the box can be moved.
For!castors!
1000!mm!
From!
the!
floor!

Sport-Thieme GmbH
38367 Grasleben
/ Germany
Tel: [phone]
Fax: [phone]
Operating/assembly instructions
Swivel castor kit for vaulting boxes
Prod. code: 122 4001
page 3 / 4
04/2016
!
!
8. Bolt!connecting pole&to the set of castors#using hex bolts and locking nut.!
*For vaulting boxes without assembly cut-outs.
%
%
View A
vaulting box
foot

Sport-Thieme GmbH
38367 Grasleben
/ Germany
Tel: [phone]
Fax: [phone]
Operating/assembly instructions
Swivel castor kit for vaulting boxes
Prod. code: 122 4001
page 4 / 4
04/2016
!
!
Caution: Do not overload the equipment!
Maintenance and care instructions
Instructions: Carry out a visual check at regular intervals. Due to our
continuous quality control of the products, technical changes
may occur which may lead to slight deviations in the instructions.
Check at regular intervals that the screw connections are tight.
Check the equipment for possible damage and replace
worn-out parts. Check the condition of wooden elements
as chipping and other signs of wear can result from use.
Ensure that moveable parts are free-moving.
We are happy to answer any questions you may
have.
Your Sport-Thieme Team