SportsPlay 601-682 User manual




8’ Standard Bench without Back ForPartNumbers:601‐682,
601‐686,601‐684and601‐688


 
ComponentDetails
ItemNo.PartNumberDescriptionQTY
1*StyleIndexBenchPlank1
2*FrameIndexBenchLeg2
3126‐7043/8x1¼”ButtonHeadBolt4
4316‐6013/8Washer4
5416‐5057/32Allen1
6516‐400LocTite1

AdditionalComponentsforPortableFrame

7*613‐614PortableBrace*2
8*126‐7013/8x1¼”ButtonHeadBolt1
9*316‐6013/8”Washer6
10*126‐6023/8”NylonLockNut3
12*126‐7043/8x3”Buttonheadbolt2

AdditionalComponentsforSurfaceMount
11**531‐0623/8ConcreteAnchor8
  
1
4
2
3
1
DetailB
4
3
2
*Onlyrequiredonunitsthathaveaportableframe.
**OnlyRequiredonSurfaceonunitsthathaveasurfacemount
frame


Note:Refertotheframeindexandstyleindexforpartidentificationand
componentspecificinstructions.


Version:8B/NBack_08.v2www.s
p
orts
p
la
y
inc.com 1






ForPartNumbers:601‐682,
601‐686,601‐684and601‐688
8’ Standard Bench without Back

Important

•Pleasekeepacopyoftheseinstructionsinyourfiles.Thereis
importantreplacementpartinformationinthemthatwillassist
youintheeventapartiseverneeded.
AssemblyInformation

•Readallassemblyinstructionbeforestartingassembly.
•Verifythatallpartswerereceivedbycomparingtheparts
receivedtothecomponentlistonpageone.
•Ifyourproductmountstosomething(surfacemount,inground
orwallmount)youwillassembletheentireproductbefore
drillingholesormountingframeinordertoensureproper
layout.
•CONTACTYOURDISTRIBUTORABOUTANYPARTSYOUARE
MISSING.Youmustreportmissingpartswithin10daysof
delivery.
•Hand‐tightenallboltsduringtheinitialassembly(unless
specificallytoldtotightencompletelyintheinstructions).Once
theunitisfullyassembledandsquareyoushouldcompletely
tightenthem.
•Otherthanwhenaspecificstepintheassemblyinstructions
specifies“tonotapplyLocTite,werecommendapplyingasmall
amounttoallassemblybolts.

GeneralMaintenance

•Itisrecommendedthatyouinspecttheproductmonthlyfor
looseboltsandbrokenparts.Ifreplacementpartsareneeded
pleaserefertotheseinstructionsforpartnumbersand
descriptionsthencallyourdistributortoorderreplacements.
2
www.sportsplayinc.com
AssemblyInstructions

NOTE:Onlyassemblyyourbenchatthistime.Afteritisassembled
youmayrefertotheframeindexsoyoucanidentifyyourframetype
andthenlocatethespecificmountinginstructionsforthatframe.

1. AttachtheBenchPlank(1)tooneoftheBenchLegs(2)by
insertingtwo3/8”x1¼”ButtonHeadBolts(3)and3/8”Washers
(4)throughthebottomofthelegandintothefactoryinstalled
nutsonthemountingplateattachedtothebottomofthebench
plank(DetailB)
2. Followingthesameprocedureestablishedinstep1,attachthe
sameBenchPlank(1)tothesecondBenchLeg(2)usingtwo3/8”x
1¼”ButtonHeadBolts(3)and3/8”Washers(4).
3. Nowidentifyyourframetypefromandfollowthespecific
instructionsforyourframe.Again,usetheframeindexpageto
completethisstep.

Version:8B/NBack_08.v2

8’ Park Bench without Back Frame
Index and Install
\\
STD Bench NB 8’ Frame Index_08.v1
www.sportsplayinc.com
Frame Index
613
-
701
I
In ground
613
-
701P
Portable
613
-
701
S
Surface
In Ground Mount Instructions:
1) IN GROUND MOUNT (Refer to the Footing Diagram
below) – Dig two holes 12” in diameter, 20” deep and
span 76” from center to center.
2) Place the bench into the holes and level (also make
sure bench is still square). Completely fill the holes with
concrete. After you add the concrete, make sure that it
didn’t cause the bench to shift out of level.
3) We recommend that the top of the concrete slope
down and away from the Bench leg to help with water
runoff.
20”
56”
12”
In
Ground Footing
Diagram
Portable
Frame Instructions:
1) After assembling the unit attach both of the cross
braces (7) to the holes located on the bottom side of
the bench in the center of the long support brace,
with one 3/8 x 1 ¼” button head bolt (8), two 3/8”
washers (9) and one 3/8” lock nut (10).
2) Attach the other end of the braces to each leg
using one 3/8 x 3” button head bolt (3), two 3/8”
washers (9) and one 3/8” lock nut (10) for each leg.
Completely tighten these bolts.
3) Finally, tighten all remaining bolts.
Surface Mount Instructions:
1) After bolts have been tightened, place the bench in the desired
permanent location and mark the holes from the mounting plate
onto the mounting surface. Move the bench
and drill the marked holes 3.75” deep with a 3/8” bit.
2) Remove the nuts and washers from the anchor
bolts (11) and place the anchor bolt into the drilled
holes. Back the bolt in the anchor out far enough so
there are sufficient threads exposed for the nut after
the bolt goes through the mounting plate and washer.
3) Put the bench back in place. Put the put a washer and
hand tightened nut on each anchor, do not completely
tighten until all nuts are hand tight. Square and level the bench
and then tighten all other bolts.

8’Bench
Style Options
www.sportsplayinc.com
Style
Index
Style Identification
In the event a replacement part is needed, it is important that you are
able to identify not only the product but the style of product you
ordered. The images to the right represent all the style options that are
available for the product you purchased. Please identify your style and
it’s corresponding part number before you contact your distributor or the
manufacturer for replacement parts.
Currently, SportsPlay Equipment offers four style options. Rolled edge
with perforated steel, beveled edge with perforated steel, rolled edge
with expanded steel and beveled edge with expanded steel.
To identify your product style you must first define the edge. If it has a
radius it is a rolled edge and if it has a 45 degree angle it is the beveled
edge. Expanded steel is easily identified by its distinct weave pattern.
The perforated steel option is simply sheet metal that has been punched
with a pattern of holes.
613-612PR 613-612PB
613-612ER 613-612EB
Rolled/Perforated Beveled/Perforated
Rolled/Expanded Beveled/Expanded