SportsPlay 602-671 User manual

Accessible Square Table with Standard
Frame 602-671 & 602-672
Component Details
Item No.
Part Number
Description
QTY
1
*Style Index
Bench Plank
3
2
*Style Index
Table Top
1
3
613
-
801
Bench Leg
8
4
604
-
601
Cross Brace
1
5
126
-
707
3/8 x 1 ½” Button Head Bolt
4
6
126
-
703
3/8 x 1” Button Head Bolt
12
7
126
-
701
3/8 x 1 ¼” Button Head Bolt
8
8
316
-
601
3/8 Washer
40
9
126
-
602
3/8” Nylon Lock Nut
12
10
126
-
505BPK
7/32 Allen
1
11
516
-
400
LocTite
1
Total
96
Version:
ECSquare_v1
www.sportsplayinc.com
1
*
Note:
Refer to the style index for part identification
.
3
5
8
4
Detail A
7
8
3
2
3
6
8
1
Detail B Detail C

Accessible Square Table with Standard Frame 602-671 & 602-672
Important
Please keep a copy of these instructions in your files. There is
important replacement part information in them that will assist
you in the event a part is ever needed.
Assembly Information
Read all assembly instruction before starting assembly.
Verify that all parts were received by comparing the parts
received to the component list on page one.
If your product mounts to something (surface mount, in ground
or wall mount) you will assemble the entire product before
drilling holes or mounting frame in order to ensure proper
layout.
CONTACT YOUR DISTRIBUTOR ABOUT ANY PARTS YOU ARE
MISSING. You must report missing parts within 10 days of
delivery.
Hand-tighten all bolts during the initial assembly (unless
specifically told to tighten completely in the instructions). Once
the unit is fully assembled and square you should completely
tighten them.
Other than when a specific step in the assembly instructions
specifies “to not apply LocTite, we recommend applying a small
amount to all assembly bolts.
General Maintenance
It is recommended that you inspect the product monthly for
loose bolts and broken parts. If replacement parts are needed
please refer to these instructions for part numbers and
descriptions then call your distributor to order replacements.
NOTE: Do not completely tighten any bolts until the unit
is completely assembled.
Assembly Instructions
1. First assemble the frame by connecting two bench legs (3) to the
cross brace (4). Positioning the legs at a 45 degree angle and
overlap the connection tabs. Then insert a 3/8 x 1 ½” button head
bolt (5) and 3/8” washer (8) through the tabs on the bench leg and
into the hole on the vertical tab of the cross brace. Attach a 3/8”
lock nut (9) to the bolt and hand tighten. Refer to Detail A on the
first page.
2. Repeat step 1 to the remaining bench legs.
3. Lay the table top face down on a piece of cardboard or cloth.
Attach the table top (2) to the bench legs (3) using the eight 3/8 x
1 ¼” button head bolts (7), 3/8’ washer (8) and 3/8’ lock nut (9).
Insert bolt through the washer, bench leg and table frame. Attach
the nut but do not tighten at this time. Refer to Detail B on the
first page for this step.
4. Attach all seat planks (1) to the bench legs (3) by inserting the 3/8
x 1” button head bolt (6) and 3/8” washer (8) through the bottom
of the bracket on the bench leg (3) and into the factory installed
nut on the bottom of the bench plank (1). Refer to Detail C on the
first page for this step.
5. Starting with one side, square the bench legs with the table and
tighten all bolts. After all the bench legs have been tightened,
square table top and tighten bolts completely.
6. Finally, inspect the entire picnic table to ensure all bots are
completely tightened.
Version: ECSquare_v1
www.sportsplayinc.com
2

Square Table Style
www.sportsplayinc.com
Style
Index
Style Identification
In the event a replacement part is needed, it is important that you are
able to identify not only the product but the style of product you
ordered. The images to the right represent all the style options that are
available for the product you purchased. Please identify your style and
it’s corresponding part number before you contact your distributor or the
manufacturer for replacement parts.
Currently, SportsPlay Equipment offers two style options for this unit.
Rolled edge with perforated steel and rolled edge with expanded steel.
To identify your product style you must first define the edge. Expanded
steel is easily identified by its distinct weave pattern. The perforated
steel option is simply sheet metal that has been punched with a pattern
of holes.
Top
Bench
613-601ER
613-602ER
Top
Bench
613
-
601PR
613
-
602PR
Expanded Rolled Edge
Perforated Rolled Edge