Springtree SM-8 User manual

Springtree Wall
Station DMX
Recorder
USER MANUAL AND
INSTALLATION GUIDE

2(615) 599-1505 www.springtree.net
Table of Contents
1. Product Information
Description................................................................................................................................3
Features....................................................................................................................................3
2. Installation
Power supply.............................................................................................................................4
Mounting....................................................................................................................................4
Connecting................................................................................................................................4
3. Programming
Programming............................................................................................................................5
4. Technical Specications
Dimensions...............................................................................................................................6
4. Troubleshooting
Troubleshooting.........................................................................................................................7
Contact us.................................................................................................................................7

3(615) 599-1505 www.springtree.net
Product Information
Description
The Springtree Wall Station is designed to be a completely
self-contained DMX controller that can be wall-mounted
(like a light switch).
The Wall Station directly outputs (or receives) DMX data so
it can be connected directly to one or more lighting xtures. After the
SM-8 has been programmed it then operates on its own without need-
ing to be connected to the lighting controller.
The SM-8 is the master and the SS-0 is the satellite. The SM-8
is connected to the SS-0 via CAT5. Up to 3 SS-0’s can be used in one
system.
Features
• Self-contained preset station with 8 scene capacity
• Built-in fade time presets
• Up to 3 satellite units
• DMX-512 output
• DMX input snapshot

4(615) 599-1505 www.springtree.net
Installation
Power Supply
Before plugging your unit in, be sure the source voltage in your area matches the voltage
required for your lighting setup. Because line voltage may vary from venue to venue, be sure your
unit voltage matches the wall outlet voltage before attempting to operate. The Springtree Wall Sta-
tion uses a standard 12V power supply (provided with the SM-8). The power for the SS-0 units are
provided by the SM-8 via CAT5.
Mounting
The SM-8 and SS-0 come with a single gang mud ring. They will not t in a standard single
gang box. Should you need to mount in a metal in-closed handy box please use a Raco 670RAC
box (pictured here, not included).
Connecting
Connect the SM-8 and SS-0 as shown below. Attention audio people: DMX is backwards
from audio. Pin 2 is negative and pin 3 is positive. Most of the time pin 2 will be a white wire and
sometimes it will be red. Pin 3 will always be black.
DMX Wiring
Pin 1 = Ground
Pin 2 = Negative
Pin 3 = Positive (Hot)

5(615) 599-1505 www.springtree.net
1. Hold down buttons 1 and 8 to enter programming mode (light will turn red).
2. Set desired look on lighting console.
3. Press desired preset button 1-8. Light will ash. Scene is stored.
4. Set new look on lighting console.
5. Press another unused button or record over existing scene by selecting button.
6. Repeat until all 8 scenes are recorded.
7. Hold down buttons 1 and 8 to exit programming mode.
• Hold down buttons 2 and 7 to enter secondary programming mode for setting fade rate (light
turns yellow). Select 1 for 1 second. 2 for 2 seconds. 3 for 3 seconds. 4 for 4 seconds and 8 for
instant (no fade rate). Hold down 2 and 7 to exit program mode.
• If DMX is present at wall station, DMX passes and the wall station is inoperable
Programming
Installation cont.
Connecting Power
The SM-8 comes with a short power whip that connects to the power supply that is provided.
If there is power close simply connect the SM-8 to the power supply. If power is not nearby, power
can be extended with 18 gauge low voltage cable.
Be sure to ground your SM-8!
The SM-8 has a short ground
whip attached to the back. This
can be grounded to the outlet
that is providing power. See
image below.
Color Guide
Purple/Pink - DMX Present from console
Blue - No DMX from console
Red - Program mode
Green - Program mode no DMX
Yellow - Fade rate mode

6(615) 599-1505 www.springtree.net
 TechnicalSpecications
Dimensions:
• Power: 12V
• Weight (SM-8): .2 lbs
(90.7g)
• Weight (SS-0): .2 lbs
(90.7g)
• Finish: Black Aluminum
Safety Precautions
• To reduce the risk of electrical shock or re, do not expose this unit to moisture.
• Be sure that the local power outlet matches that of the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt
to remove or break o󰀨 the ground prong from the electrical cord. This prong is used to
reduce the risk of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• This xture is intended for indoor use ONLY!
• Keep this manual for as long as you own this product!
4 1/4”
(107.95mm)
2 3/4” (69.85mm)
1 5/8”
(41.28mm)

7(615) 599-1505 www.springtree.net
 Ocehours:
Monday-Friday,
8:30 AM to 5:00 PM CT
Telephone:
[phone]
E-mail:
[email protected]
Website:
www.springtree.net
Troubleshooting
MasterUnitnotresponding:
1. Check that the 12V power supply is plugged in and connected to the SM-8.
2. Check that the DMX cables are connected properly and are wired correctly.
3. Is the SM-8 receiving DMX from the controller? DMX from the controller will override
the SM-8.
SlaveUnitnotresponding:
1. Check that the CAT5 cable is connected from the SM-8 to the SS-0.
2. Check that the SM-8 is powered up.
Contact us
Springtree Media Group would like to thank you for choosing our company for
your lighting needs! If you have any questions or concerns, please contact us.