Square Scrub Doodle Scrub EBG-9 User manual

Owner’s
Manual
Original
Instructions
EBG-9
EBG Series
Surface Preparation Machines
www.squarescrub.com / 800.557.6822
Doodle
SCRUB

Doodle Scrub by Square Scrub
Owner’s Manual
About your Doodle Scrub
Floor Surface Preparation Machine
The Doodle Scrub offers a 1/4 hp, 4100 rpm motor, a heavy duty powder coated
10 gauge steel frame, and a two-position handle. The option to connect the
handle on either the side of the machine or at the back offers the exibility to
adjust the machine to suit your needs. At 22 lbs, the Doodle Scrub offers nearly
the same pounds per square inch as its parent machine, the EBG-20/C.
The Doodle Scrub is designed to go where larger machines can’t. Cleaning stairs,
around the toilet, under bathroom sinks is easy with the Doodle Scrub. This
makes it the perfect companion to other EBG Series Floor Preparation Machines.
Please visit our website at www.squarescrub.com for informative videos and
literature.
Contents
• Introduction
• Manual Conventions
• Safety / Important
• Machine Transport
• Operating Instructions
• Troubleshooting Guide
• Parts Breakdown
• Warranty Information
• Pad Information
page 1
WARNING OF POTENTIAL INJURY! MOVING PARTS! UNPLUG BEFORE SERVICING!
This product contains moving parts. To reduce the risk of injury, unplug before servicing.
General Safety
- This oor-nishing machine shall be grounded while in use to protect the operator from
electric shock. The machine is provided with a three-conductor cord and a three-contact
grounding type attachment plug to t the proper grounding type receptacle. The green (or
green and yellow) conductor in the cord is the grounding wire. Never connect this wire to
anything other than the grounding pin of the attachment plug.
- This machine is for use on a nominal 120-volt circuit and has a grounding plug that
resembles the plug in gure 1. Make sure that the machine is connected to an outlet
having the same conguration as the plug. See gure 1 on page 2.
No adapter should be used with this machine.
Introduction
You are now the proud owner of an EBG-Series machine.
This machine is a product of Square Scrub. It is made of
ne materials and will give you many years of satisfactory
service if maintained and used according to the guidelines in
this owner’s manual.
Please read all Installation, Operation, and Safety
Instructions before using this machine.
***This product is for Industrial/Institutional/Commercial Use Only***

page 2
***gure 1
Maintenance Schedule
Prior to using (daily)
• Check AC power cord. Do NOT operate equipment if AC power cord is cut, frayed or if
ground is missing.
• Check grip face and driver pad : inspect for wear/debris. Replace as needed.
After use (daily)
• Clean pad and base plate assembly : remove/replace pad as needed.
• Inspect grip face for wear. Remove debris between grip face and base
plate.
• Wipe entire unit with damp microber cloth.
• Make certain a pad is placed on grip face.
Weekly Preventive Maintenance
• Check grip face for wear.
• Use vacuum to clean away debris build-up around base plate.
Annually
• Replace ALL isolators.
• Bearing Assembly Replacement*
*The Bearing assembly is considered to be a wear item. We recommend that the bearing
assembly be replaced as needed. Unit will become noisy when bearing needs to be
replaced.
***NOTE: Be sure to replace isolators when you replace the bearing.

Manual Conventions
Danger:Indicates an imminently hazardous situation which, if not avoided, may result
in death or serious injury.
Caution:Indicates that machine or property damage could result if instructions are not
followed.
Note:Provides helpful information. Severe bodily injury or death can occur to you or other
personnel if warnings found on this machine or in this owner’s manual are ignored. Read and
observe all statements and instructions found on the machine and in the owner’s manual.
Who to call for assistance
If you work with a Square Scrub-authorized distributor, contact them for assistance.
If any contents of the box are missing, contact your Square Scrub-authorized dealer. If you
purchased your machine directly from Square Scrub, contact Square Scrub at 1.800.557.6822
for service in the United States and Canada. For worldwide service, call Square Scrub directly
at 870.930.9898. Make sure you have the machine’s serial number, located on the handle of the
machine, when you call.
Liability statement
This Square Scrub product has been built to the highest industry standards. Please note and
heed the WARNING and caution labels that have been placed on the equipment and in this
manual for your safety. PLEASE DO NOT ATTEMPT TO OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT ADEQUATE TRAINING. ANY USE, OPERATION OR REPAIR IN
CONTRAVENTION OF THIS DOCUMENT IS AT YOUR OWN RISK. BY ACCEPTANCE OF THIS
SYSTEM YOU HEREBY ASSUME ALL LIABILITY CONSEQUENT TO YOUR USE OR MISUSE
OF THIS EQUIPMENT. SQUARE SCRUB SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGE OF ANY KIND.
Equipment specications, applications and options are subject to change at the sole discretion of
Square Scrub without notice.
Safety
All Square Scrub products are built to strict safety and reliability specications in accordance with
industry standards. Therefore, safety issues pertaining to operation and repair of Square Scrub
equipment are primarily environmental and human interface. The following basic safety tips are
given to ensure safe installation, operation and maintenance of Square Scrub.
page 3

page 4
Important
• Caution - This machine is intended for indoor use only.
• Caution - This machine is to be stored indoors only.
• Never leave the machine unattended while power cord is
connected.
• Do not operate this machine while under the inuence of alcohol or
other drugs.
• Never allow children under age 18 to operate this machine.
• Unplug machine from power source before changing pad.
• Always wear personal protective equipment (PPE) when operating this machine.
• Never inhale dust created by the use of this machine. Any modications to this machine may
result in damage to the machine or injury to the operator or others nearby. Alterations to the
machine will also void any and all warranty and liabilities.
• Sanding wood decks is not recommended by Square Scrub due to uneven surfaces which
could lead to damage to the machine. Some pressure treated wood found in
decking contains arsenic that, when sanded, will create hazardous dust. Square Scrub
assumes no liability if the machine is used on decks, and damage caused from sanding
pressure treated wood will not be warranted.
• Do not operate this machine around fuels, solvents, ammable oor nishes, thinners, wood
particulate or any ammable materials. Cigarette lighters, pilot lights, electrical sparks and
all other sources of ignition should be extinguished or avoided. Work areas should be well
ventilated.
• Keep the power cord clear of the pad. Always lift the cord over the machine. Do not pull on
the power cord in an attempt to move the machine. This could result in electrocution.
Operating this machine with a damaged power cord could lead to electrocution or re. Cord
should remain clear of moving parts during operation. Never use the cord to navigate the
machine. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
• Servicing this machine while still connected to a power source could lead to
electrocution or re. Before performing machine service or maintenance, disconnect the
machine from it’s power source.
• Do not use machine if it has been sprayed with water or left out in the rain. This could result
in a shock injury or electrocution.
• Keep feet, hands, and loose clothing away from any moving parts on the machine to avoid
injury. Disconnect power cord before changing the pad or when servicing. Damage can occur
to the machine or to other property if instructions in the owner’s manual are not followed.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Warning: This appliance is not suitable for picking up hazardous dust.
PPE Equipment

page 5
Transport of Machine
To transport this machine, the following procedure is advised:
• Unplug machine from power source.
• Always leave a pad on the machine to protect the grip face from damage in transport and
storage.
• Secure machine when transporting in a vehicle to prevent movement.
• NEVER PICK THE DOODLE SCRUB UP BY THE HANDLE ALONE! Always pick the Doodle
Scrub EBG-9 up with one hand on the handle and the other hand picking up the base. Failure to
do so could possibly damage or ruin your machine.
Operating Instructions
1. Move machine to work location. Never operate, transport, or store the machine without
a pad to protect the grip face.
2. Afx the handle clip onto either of the two provided base clips.
3. Plug machine into grounded power outlet.
4. Hold the machine’s handle with one hand while gently pressing the switch on the top of
the handle with the other hand.
5. Begin moving the machine over the oor in either a mop-like motion or along edges.
6. Continue moving the machine over the selected surface, checking your pad every 15 to 30
minutes (depending on pad in use) to maintain optimum performance.
Airborne Noise and Vibration Emissions
Sound Power Level:
120V:
Under 57 dBA
240V:
Under 57 dBA
Vibration Total at Base:
120V:
Avg. 6.5 mm/s2, max at 6.9 mm/s2
240V:
Avg. 5.8 mm/s2, max at 6.0 mm/s2

page 6
Important
HANDLE ATTACHMENT
The Doodle Scrub EBG-9 comes with two different ways of connecting the handle to the base. It
is extremely important that you connect the handle correctly to the base or else you run the risk
of excessive noise and rattle. Figure 2 and gure 3 shows the incorrect and correct way to attach
the handle to the Doodle Scrub EBG-9.
***gure 2
Incorrect way
of attaching handle to
the Doodle Scrub base.
***gure 3
Correct way of
attaching handle to
the Doodle Scrub base.

page 7
Problem Cause Action
Unit runs correctly but stops. It
works ne after 3-10 minutes
Incorrect pad is being used.
Only use pads recommended
by Square Scrub. Pads are not
to exceed “5.25”x”10.5”.
SS P0511BLU - Driver Pad
SS P0511DRIVER - Thin Pad
SS P0511SHO - Wet Strip Pad
SS P0511SQP - Dry Prep Pad
SS P0511WHT - Thick Pad
SS P0511XTR - Dry Earase Pad
SS P0511TGB - Blue Tile &
Grout Pad
Maximum Wet Weight: 5oz.
***NOTE: DO NOT USE GREEN
TILE AND GROUT PAD ON THE
EBG-9 DOODLE SCRUB.
Use correct pad. If problem continues
contact your nearest Square Scrub
Dealer.
Machine will not start Not Connected to power source
Voltage too low
Defective switch
Check power source connection and
lighted plug
Have electrician check outlet
Contact Square Scrub dealer
Runs erratically Low voltage from excessive
length or undersized
extension cord
Defective start switch
Defective motor low voltage
Use 10 gauge extension cord
Not more than 25’ long
Contact Square Scrub dealer
Contact Square Scrub dealer
Fuse/Circuit Breaker Trips Low voltage
Low input volts
Allow the motor to cool.
Eliminate extension cord.
Locate power cord closer to work site.
Have voltage checked by
electrician.
Machine pulls hard to one side
Note: The rubber isolators on the EBG are
considered wear items. It is recommended to
replace the entire set of all four isolators once
per year (or sooner under heavy use) to prevent
failure and damage to the machine.
Worn Pad
Rubber isolators are worn out
Rotate pad 180 degrees
Flip pad over
Replace Pad
Replace isolators
Machine is noticeably louder than
it was when originally purchased Rubber isolators worn Replace isolators
Troubleshooting

Machine Serial #:_____________________
Date of Purchase:_____________________
page 8
Doodle Scrub 1 Year Limited Warranty on parts
and 90 days Limited Warranty on Labor
General
This Square Scrub EBG-9 Doodle Scrub Floor Preparation Machine is warranted to be free from
defects in materials and workmanship under normal use and service for a period of one year
on machine handle and base when operated and maintained in accordance with Square Scrub
Maintenance and Operating Instructions. The warranty will commence on the purchase date by
the original end user from an authorized Square Scrub dealer and is subject to proof of purchase.
If proof of purchase cannot be provided, the warranty shall begin from the date of shipment to an
authorized Square Scrub dealer. Parts replaced or repaired under warranty are guaranteed for the
remainder of the original warranty period. The warranty period is subject to the conditions stated
below.
Labor to repair the unit is also included for the rst 90 days from date of original purchase. Unit
must be returned to Square Scrub for all repairs other than the handle switch. End user must ship
the unit to Square Scrub at their expenses. Unit will be repaired or replaced and returned to the
end user or the authorized Square Scrub dealer by normal ground shipping method at Square
Scrub’s expense. Square Scrub is not responsible for lost time involved in the repair time.
Disqualications
This warranty shall not apply to repairs resulting from accidents or misuse, damage in transit,
overloading the capacity of the machine, damage resulting from lack of proper maintenance or
care as described in the Maintenance Schedule and General Operating Instructions listed in the
Owner’s Manual. Minor adjustments, not related to the replacement of parts, are not covered.
Repairs or alterations made by an organization other than the factory or an Authorized Service
Center are not covered and will void warranty as it relates to the parts or systems repaired or
altered by the non-authorized organization.
Product Exceptions & Exclusions Wear Items
If a difculty develops with the product, contact your local Square Scrub dealer or call Square
Scrub at 800.557.6822. Only Square Scrub can authorize repairs under warranty. Square Scrub
may elect to require the return of components to validate a claim. Any defective part to be returned
must be shipped freight prepaid to an authorized Square Scrub Dealer/Service Center or to the
Square Scrub factory. Travel time and mileage is not covered on any repairs.
Square Scrub’s liability under this warranty is limited to repair of the product and/or replacement of
parts and is given to purchaser is lieu of all other remedies, including INCIDENTAL AND
CONSEQUENTIAL DAMAGES. THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THOSE SPECIFIED HEREIN. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY, SHALL BE IMPLIED.
Please register your machine on our website within thirty (30) days of purchase to assist Square
Scrub in providing the performance you expect from your new oor machine.
Repairs after the rst 90 days of the warranty period but still during the rst 12 months will be
done for $69 to cover labor and Square Scrub will prepay the shipping to return the Doodle Scrub
if it is an under warranty repair.
Repairs after the rst 12 months will be done for $69 at fee plus the cost of parts and shipping.
Square Scrub
800-557-6822
www.squarescrub.com
• Machine Cord
• Blue Driver Pad (shipped with machine)
• Grip Face
• Cushion hand grip
• Rubber Isolators
• Eccentric Assembly (includes bearing)

2
Item
No.
Part No. Part Descripon
1SS 051104 Switch Assembly
2SS 051150 Handle Assembly
3SS 051160 Base Assembly
4SS 051103 Grip Face
1
3
4
page 9

page 10
Blue Driver Pad * SS P0511BLU * 5.25x10.5
This medium to heavy duty Blue pad can be used for heavier cleaning and bufng situations
but primarily used as a spacer pad. Always check spacer and driver pads frequently for wear
and replace as needed! Use wet or dry on VCT and tile. Can be used for heavier cleaning and
bufng situations.
18/cs
White Driver Pad * SS P0511DRIVER * 5.25x10.5
The Driver pad is designed to provide a spacer between your sandpaper and the machine. Just
1/4” thick, Use this pad with Sandpaper and Resin diamonds. Always check spacer and driver
pads frequently for wear and replace as needed! Change pad often to protect oor.
48/cs
SHO Pad * SS P0511SHO * 5.25x10.5
The SHO pad should be used only for the heaviest of chemical stripping jobs. Extremely
abrasive and heavy, dense bers. Best when dirt and buildup are severe. Use wet on VCT and
tile. 20/cs
SQP Pad * SS P0511SQP * 5.25x10.5
SQP is a thin pad designed to remove oor nish without chemicals. Remove several layers of
acrylic nish to prep for recoating. Use dry or wet on VCT and tile.
60/cs
White Pad * SS P0511WHT * 5.25x10.5
The White pad is used as a light duty polish pad. The 1” thick pad is used without a driver pad
and is great for spreading chemcials while bufng.
16/cs
Xtreme Sponge * SS P0511XTR * 5.25x10.5
Use the Xtreme Sponge to remove scuff marks on VCT or bathroom tile. A little water and this
melamine pad deep cleans and restores shine between renishing jobs. Use wet on VCT and
bathroom tile.
5/cs
Blue Tile and Grout Pad * SS P0511TGB * 4.75x10
Our Tile and Grout pad is best on grouted tile oors, but can be used very effectively on
terrazzo, poured non-slip, concrete and other uneven oors. Use wet on several surfaces.
Sold Individually
***Specications and information contained in this manual are subject to change without notice
Doodle Scrub Pad Ordering
Information

Register your
Square Scrub Product:
Online
http://www.squarescrub.com
American Made
Doodle
SCRUB
R3.1 11/3/2015