Squareled EXPO User manual

SquareLED - EXPO

Manual | EXPO
1. Product Overview

Manual | EXPO
2. Mechanical Specication
Packaging: Thanks for your purchasing the AH055. All the lights have been checked and are in excellent
operating condition. Please check the shipping carton rst,because there may be damage occurred during the
shipment.Then check the lights carefully and be sure that the lights is intact and works normally.In the event
damage has been found, spare parts are missing or the lights works abnormally,please contact us for further
instructions. And please don’t return the lights to the dealer before contacting us.
Introduction: The AH055 has three operating modes: DMX mode, Auto mode and Master/Slave. And the lights
has three DMX modes, including channel 1,channel 2,channel 5.There are ve built-in Auto programs and you
can see ve kinds of shows when you open the Auto mode. In addition, you can connect several pieces of lights
in DMX mode and set one in Auto mode, and the others in Master/Slave mode. And then all the lights in Master/
Slave mode will run following the one in Auto mode. Using fog or special eect smoke, you can see better show-
ing eect.
Warning!
1.Don’t expose the lights to rain or moisture,for the sake of preventing the risk of electrical shock or re.
2.Don’t look directly at the opening lights all the time,or it may damage your eyes.

Manual | EXPO
4. Features
• Light Source:31*10W CW LEDs
• Lens:20°
• Power consumption:350W
• Voltage:100V-240V, 50/60Hz
• Run Mode: DMX 512/Master Slave/Auto Run
• 4 dierent dimming curve
• Maximum 66 ID setng for easy separate control
• DMX Channels: 1, 2 & 5CH
• Built-in Eect: color mixing, variable color chasing, strobing and fading.
• TFT displayer with four buttons
• Material: Aluminum body
• IP20
• Temperature: -30‘C-45‘C
• Dimension: 234×494.5 mm
• N.W. : 6.4 KG
• G.W. : 7.8 KG4.1 Rear Panel
5. Mounting
When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without
any deformation. When installing the unit must be secured with a secondary safety attach-ment, e.g. and appro-
priate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation mate-
rial being used, and perodic safety inspection of all installation material and unit. If you lack these qualifcations,
do not attempt the installation yourself. The installaiton should be checked by a skilled person once a year.
The Inno Pocket Spot is fully operational in
two dierent mounting positions, hanging
upside-down from a ceiling or set on a at
level surface. To avoid internal damage to
the unit, never mount the unit on its side as
illustrated above. Be sure this fxture is kept
at least 0.5m away from any ammable
materials (decoration etc.). And you’d better
use and install the supplied safety cable as
a safety measure to prevent accidental da-
mage and/or injury in the event the clamp
fails (see next page).

Manual | EXPO
5. Programme Menu

Manual | EXPO
7. Displayer introduction
1. DMX means the light is in the DMX mode.Similarly,SLAVE means the light is in the SLAVE mode.
2. The color of the point shows the condition of signal transmission. Green represents the good condition, while
red represents the signal is interrupted.
3. The item shows the working temperature of the light.When the working temperature exceeds the max
temperature,the color of the letters and number will change from white to yellow.
4. This item shows the menu you selected.
5. This item shows the condition of key lock.“Key lock open”means the key lock is open.And“Key lock o”means
the key lock is close.
STAT COLOR-In this menu, you can adjust the value of static color and strobe speed as you like.
1. Press“ENTER”button and then UP or DOWN button until“STAT COLOR”is showed.
2. Press“ENTER”button, and there are six options.Then press ENTER to select the option and press UP or DOWN
button to select the value you desire as below:
1) STAT WHITE - You can adjust the white brightness in this menu.
2) STAT STROB - You can adjust the strobe speed in this menu
AUTO-In this menu, you can select your desire AUTO mode and adjust the running speed.
1. Press“ENTER”button and then UP or DOWN button until“AUTO”is showed.
2. Press“ENTER”button, and“SPEED”or“AUTO MODE”will be showed. Then press ENTER and you can see two
items as below:
1) SPEED - You can select your desired speed in this menu.
2) AUTO MODE - You can select your desired auto mode in this menu.INFORMATION-In this menu, you can learn
about the information of software, hardware and the working time of the light.
1. Press“ENTER”button and then UP or DOWN button until“INFORMATION”is showed.
2. Press“ENTER”button, and“Software”“Hardware”or“Fix times”will be showed.Then press

Manual | EXPO
ENTER, and you can see three items as below:
1) Software - This item displays the Software information.
2) Hardware - This item displays the Hardware information.
3) Fix times -This item displays the working hours about the light.
SET UP-In this menu, you can adjust the value of the the function.
1. Press“ENTER”button and then UP or DOWN button until“SET UP”is showed.
2. Press“ENTER”button, and there will be nine options.Then,press ENTER to select the option and press UP or
DOWN button to select the value you desire as below.
1) ID number - You can select an ID Number in this menu.Then, you can adjust the value of channel 11 to the
corresponding scope and control the light individually with control console.
2) Display Led - In this item,you can select“ON”or“OFF”.If you select ON,the displayer will be on all the time.And
if you select OFF,the displayer will extinguish about ten seconds later.
3) Key locks -You can select whether the password is on or o in this menu , and the password is [ DOWN ] + [
UP ] + [ DOWN ] + [ UP ] .If you select“on”,then you have to input the password before pressing the buttons.
Otherwise,the light won’t respond to your order.
4) Max temp - You can set the your desired Max working temperature about the light in this menu.When the wor-
king temperature of the light exceeds the Max temperature, the color of letter“Temp xx”showed in the menu
will change from white to yellow.Meanwhile, the light will adjust the working temperature automatically.
5) Dimmer WHITE - You can adjust the white brightness in this menu.
RUN MODE-In this menu, you can select DMX mode or SLAVE mode.
In SLAVE mode,you can select one light as the MASTER light and other lights in SLAVE mode will run following
the MASTER light.
1. Press“ENTER”button and then UP or DOWN button until“RUN MODE”is showed.
2.Press“ENTER”button, and“DMX”or“SLAVE”will be showed, then press ENTER to select your desired mode.
DMX-In this menu,you can connect several pieces of lights with DMX cable and control them with
control console.
1. Press“ENTER”button and then UP or DOWN button until“DMX ”is showed.
2. Press“ENTER”button, and“CHANNEL”or“ADDRESS”will be showed.Then press ENTER.
1)“Channel [xx]”will be showed,“X”represents the showed DMX channel mode. You can press the UP or DOWN
button to select your desired Channel mode.
2)“xxx”will be showed,“x”represents the showed address. You can press the UP or DOWN button to select your
desired address.
RESET-In this menu, you can reset all the value of the system.
1. Press“ENTER”button and then UP or DOWN button until“RE

Manual | EXPO
8. DMX control mode
DMX 1 channel
channel value function
10 - 255 Adjust CW All LED dimmer
DMX 2 channel
channel value function
10 - 255 Adjust CW All LED dimmer
2
0 - 8 NO function
9 - 255 Strobe(from slow to fast)
DMX 5 channel
channel value function
10 - 255 Adjust CW All LED dimmer
2
0 - 8 NO function
9 - 255 Strobe(from slow to fast)
3
0 - 9 Default
10 - 50 Auto 1
51 - 100 Auto 2
101 - 150 Auto 3
151 - 200 Auto 4
200 - 255 Auto 5
0 -255 Auto mode speeds
0 -255 Id address set
40 - 255 Auto mode speeds
50 - 255 Id address set

Manual | EXPO
Channel 5 (Id address set)
0 - 9 all Ids
10 - 19 Id1
20 - 29 Id2
30 - 39 Id3
40 - 49 Id4
50 - 59 Id5
60 - 69 Id6
70 - 79 Id7
80 - 89 Id8
90 - 99 Id9
100 - 109 Id10
110 - 119 Id11
120 - 129 Id12
130 - 139 Id13
140 - 149 Id14
150 - 159 Id15
160 - 169 Id16
170 - 179 Id17
180 - 189 Id18
190 - 199 Id19
200 - 209 Id20
210 Id21
211 Id22
212 Id23
213 Id24
214 Id25
215 Id26
216 Id27
217 Id28
218 Id29
219 Id30
220 Id31
221 Id32
222 Id33
223 Id34
224 Id35
225 Id36
226 Id37
227 Id38
228 Id39
229 Id40
230 Id41
231 Id42
232 Id43
233 Id44
234 Id45
235 Id46
236 Id47
237 Id48
238 Id49
239 Id50
240 Id51
241 Id52
242 Id53
243 Id54
244 Id55
245 Id56
246 Id57
247 Id58
248 Id59
249 Id60
250 Id61
251 Id62
252 Id63
253 Id64
254 Id65
255 Id66
9. DMX-512 addressing with ID address
1. Follow instructions 1 for DMX 512 addressing.
2. Activate ID addressing in each xture by setting panel function“ID ON/OFF”to ON.“Settings”to“ID ON/OFF”
to“ON”For every DMX 512 starting address the user can set 66 separate ID addresses. Set ID addresses in
each xture by setting panel function“ ID address”to incremental values.(l.e. 1, 12, 24, 36 etc...)“Settings”to
“address”to“01~66”.

Manual | EXPO
10. CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
DMX connector conguration
Caution: Do not allow contact between the ground and the xture’s chassis ground. Grounding the ground can
cause a ground loop, and your xture may perform erratically. Test cables with an ohm meter to verify positive
pole and to make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART
Note!
If you use a controller with a 5 pin DMX output connector, you need to use a 5 pin to 3 pin adapter. The chart below
details a proper cable conversion:
3-PIN TO 5-PIN CONVERSION CHART
Conductor 3 Pin Female (output) 5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use

Manual | EXPO
11. Change LED board
1. Remove the nine screws on the light panel with a screwdriver.
2. Take down the whole light panel.
3. And then install the whole light panel of 25 degree.
12. Photometric Data

Manual | EXPO
Das Lichttechnikhaus Vertriebs GmbH
Rudolf-Diesel-Str. 3, D-89312 Günzburg
Telefon [phone]
Fax [phone]
E-Mail [email protected]
Web www.lth-gmbh.de