Squareled STORM 5 User manual

User Manual: SquareLED Storm 5

Manual | Storm 5
1. Introduction
Thank you for having chosen our LED lighting Unpack the device, inside the box you should nd:
The xture device One power cable One XLR connection cable This manual
Please check carefully that there is no damage caused by transportation. Should there be any problems,
consult your dealer and don’t install this device.
Packing List
Easy multi fixture hanging system, outdoor version available
44pcs RGBW 4in1 LED, no ultraviolet radiation
More than 50,000 hours for the LED light source
11,000 lm
35/20 degree selectable
1/3/4/5/10/14/15 DMX channels
16 Bit Dimmer
DMX Mode /Master-slave mode
AC 100-240V 50/60Hz 260W
Diecasting heatsink, with low noise fans
With temperature sensor to extend the lamp life
2000 Hz LED scan rate
L 490mm x H 285mm x W 105mm, Weight 9Kg
IP65/IP20 selectable
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in
this user manual.
This device falls under protection-class I. Therefore it is essential that the device should be earthed. The electric
connection must carry out by qualied person. If the external exible cable or cord of this luminaire is dama-
ged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualied person in
order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the end of this manual.
»
»
»
»
»
»
»
»
»
»
»
»
»
»

Manual | Storm 5
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement
of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging the power cord.
Never look directly into the light source,
as sensitive persons may suer an epileptic shock.
Important:
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
3. Connections
DMX-512 control connection
The product has a DMX 512 input tted with 3-pin XLR connectors. Screened cables in compliance with EIA
RS-485 specications and the following characteristics must be used for connections:
2 conductors plus screen
120Ohm impedance
low capacitance
max. transmission rate 250kBaud.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 OHM
resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last xture
in the chain.
»
»
»
»

Manual | Storm 5
Display Menu
Main menu Sub-menu
adress DMX Adress Setting
cong channel channel 1Ch
channel 3Ch
channel 4Ch
channel 5Ch
channel 10Ch
channel 15Ch
Dimmer Curve Mode L
Mode Q
Mode I
Mode S
Cipher Setup 0-999
Key Mode Lock
Unlock
Temp Uint CS Celsius Degree
Fahrenheit Degree
DMX Status Value Clear
Value Hold
Display Mode Auto
On
System Info Temp
Hour
Color Menu Red 0-255
Green 0-255
Blue 0-255
White 0-255
White Balance Set Red 0-255
Set Green 0-255
Set Blue 0-255
Static color Color 0-51
Auto Test
Load Default
Firmware Version

Manual | Storm 5
4. Main functions
Address: Current DMX address
A. Setting DMX address by button
Press ENTER button when show the address menu, then adjust the DMX address by pressing [UP] or
[DOWN] button
Press [ENTER] to confirm or pressing [ESC] to return to main menu.
B. Setting DMX address by controller
Set the DMX value of channel 5 to 10-15,channel 17 to 20-26, channel 7 to 30-36, channel 8 to 40-46,
then the devices connected to the controller will enter to the setting address mode
Set the DMX value of channel 1 from 0-59, then you will see the the first number of the Address change
to (channel 1 vaule)/10. For example, when set the value of channel 1 to 20, the first DMX address number
will be 2 (20/10=2)
Set the DMX value of channel 2 from 0-99,then you will see the the sencond number of the Address change
to (channel 2 vaule)/10. For example, when set the value of channel 2 to 30, the first DMX address number will
be 2 (30/10=3)
Set the DMX value of channel 3 from 0-99,then you will see the the third number of the Address change
to (channel 3 vaule)/10. For example,when set the value of channel 1 to 40, the first DMX address number
will be 3 (40/10=4), and the DMX address you set by conctroller will be 234.
Set the DMX value of channel 4 to 255, then you will save the DMX address setted by the controller.
Caution: It won’t save the address if the address number is over 512
Set the value of channel 5-8 out of the value range show on the step 1, and the device will exit the setting
address mode
Cong
Setting DMX mode:
Press ENTER button when show the channel menu, then select the DMX mode by pressing
[UP] or [DOWN] button
Setting Dimmer Curve:
Press ENTER button when show the dimmer curve menu, then select the dimmer curve by pressing
[UP] or [DOWN] button
Setting Cipher:
Press ENTER button when show the cipher setup menu, then setup cipher by pressing [UP] or [DOWN] button
Key mode:
Press ENTER button when show the key mode menu, then select lock or unlock by pressing [UP] or
[DOWN] button
»
»
»
»
»
»
»
»
»
»
»
»
»

Manual | Storm 5
Show Temperature:
Press ENTER button when show the Temp Uint CS menu, select the way of showing the fixture’s
temperature in °C or °F by pressing [UP] or [DOWN] button
DMX status:
Press ENTER button when show the DMX Status menu, then select clear value or hold value by pressing [UP]
or [DOWN] button
Display mode:
Press ENTER button when show the Display Mode menu, then select auto or on by pressing [UP] or [DOWN] button
System info
Temperature:
Press ENTER button when show the Temperature menu, then it will show the temperature of the fixture
Fixture time:
Press ENTER button when show the Fixture time menu, then it will show how long time of the fixture
already used
Color menu
Press ENTER button when show the Color menu, press Enter button to select the color mode, then adjust the
color by pressing [UP] or [DOWN] button
White balance
Press ENTER button when show the white balance menu, press Enter button to select the color mode, then
adjust the color by pressing [UP] or [DOWN] button
Auto test
Press ENTER button when show the auto test menu, select test mode by pressing [UP] or [DOWN] button
»
»
»
»
»

Manual | Storm 5
5. DMX functions and values
DMX Channel (1CH)
Channel DMX Value Control Function
1CH 0–255 Static color
DMX Channel (3CH)
Channel DMX Value Control Function
1CH 0–255 R 0–100%
2CH 0–255 G 0–100%
3CH 0–255 B 0–100%
DMX Channel (4CH)
Channel DMX Value Control Function
1CH 0–255 R 0–100%
2CH 0–255 G 0–100%
3CH 0–255 B 0–100%
4CH 0–255 W 0–100%
DMX Channel (5CH)
Channel DMX Value Control Function
1CH 0–255 Master dimmer
2CH 0–255 R 0–100%
3CH 0–255 G 0–100%
4CH 0–255 B 0–100%
5CH 0–255 W 0–100%

Manual | Storm 5
DMX Channel (10CH)
Channel DMX Value Control Function
1CH 0–255 Master dimmer
2CH 0–255 Master dimmer ne
3CH 0–255 Red dimmer
4CH 0–255 Red dimmer ne
5CH 0–255 Green dimmer
6CH 0–255 Green dimmer ne
7CH 0–255 Blue dimmer
8CH 0–255 Blue dimmer ne
9CH 0–255 White dimmer
10CH 0–255 White dimmer ne
DMX Channel (14CH)
Channel DMX Value Control Function
1CH 0–255 Master dimmer
2CH 0–255 Red1 dimmer
3CH 0–255 Green1 dimmer
4CH 0–255 Blue1 dimmer
5CH 0–255 White1 dimmer
6CH 0–255 Red2 dimmer
7CH 0–255 Green2 dimmer
8CH 0–255 Blue2 dimmer
9CH 0–255 White2 dimmer
10CH 0–15 No Eect
0-255 Strobe Rate (0-30HZ)
11CH 0-255 Color Macro ,Color + Black
12CH
0-35
36-71
72-107
108-143
144-179
180-215
216-255
Auto run
No Eect
ramp up
ramp down
ramp up/down
color mix mode
4-colors
8-colors

Manual | Storm 5
13CH 0-255 dimmer speed
14CH
0-63
64-127
128-191
192-255
dimmer curve
L curve
S curve
I curve
Q curve
DMX Channel (15CH)
Channel DMX Value Control Function
1CH 0–255 Master dimmer
2CH 0–255 Master dimmer ne
3CH 0–255 Red dimmer
4CH 0–255 Red dimmer ne
5CH 0–255 Green dimmer
6CH 0–255 Green dimmer ne
7CH 0–255 Blue dimmer
8CH 0–255 Blue dimmer ne
9CH 0–255 White dimmer
10CH 0–255 White dimmer ne
11CH 0-15 No Eect
16-255 Strobe Rate (0 - 30HZ)
12CH 0–255 Color Macro, Color+Black
13CH
0-35
36-71
72-107
108-143
144-179
180-215
216-255
Auto run
No Eect
ramp up
ramp down
ramp up/down
color mix mode
4-colors
8-colors
13CH 0-255 dimmer speed
14CH
0-63
64-127
128-191
192-255
dimmer curve
L curve
S curve
I curve
Q curve

Manual | Storm 5
15CH
0-63
64-127
128-191
192-255
dimmer curve
L curve
S curve
I curve
Q curve
6. Cleaning and maintenance
We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use
alcohol or solvents!
Disconnect from mains before starting maintenance operation.
There are no servicable parts inside the device. Maintenance and service operations are only to be carried out
by authorized dealers. If you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers only in
order to avoid hazards.
If you have further questions, please contact your dealer.
7. Instalation
The device must only be installed at a vibration-free, oscilation-free and re-resistant location.