SRS Lighting DST5-RDM User manual

( 1 / 4)
Instruction Manual
Models:
version 1.0 since 3 February 2020
ATTENTION!
This instruction manual contains important information about the installation and the use of
the equipment. Please read and follow these instructions carefully.
Always ensure that the power to the equipment is disconnected before opening the
equipment or commencing any maintenance wor .
DST5-RDM_en_manual_M087
ST5-R M MX Splitter
ST5-R M-3, ST5-R M-5
ST5-R M-C

( 2 / 4)
IMPORTANT SAFETY INFORMATION
The following general safety precautions have to be observed during all phases
of operation, service, and the repair of this equipment. Failure to comply with
these precautions or with specific warnings in this manual violates safety
standards of design, manufacture, and the intended use of this equipment.
Do not operate in an explosive atmosphere!
Do not operate this equipment in the presence of flammable gases or fumes.
Operation of any electrical instrument in such an environment constitutes
a definite safety hazard. Device should be never placed near or over a heat
register or other source of heated air and it should not be installed or operated
without proper ventilation.
Mains AC100-255V connection
AC power is connected to the splitter via Neutri PowerCon blue connector.
Standard supply is UNISCHUKO lead with Neutri PowerCon. Always respect the
mar up of L and N on connectors for correct wiring of Line and Neutral.
DMX connection
DMX connectors are located on one side of the splitter board. These are
separated to two groups. First group is wired in ratio 1:1 and mar ed as DMX
input and DMX thru. This line is not optically isolated and when the device is last
in line, it should be terminated by the termination resistor by switching the
120ohm switch on. Termination activity is indicated by an LED.
The other group consists of five optically isolated lines mar ed with letters A-E.
Each line has a separate power supply, line driver and the indication of signals
D+, D- on both signal lines. These LEDs are active when splitter is retransmitting
DMX signal and there is no short circuit between data lines.
In case of short circuit between data pins D+/D- and the CMN pin, the LED
connected to the data line is off.
Pin 1 Ground / Common
Pin 2 Data -
Pin 3 Data +

( 3 / 4)
Front anel: Rear anel:
Device in use / service:
By default, Power LED indicates the device is on main power. When the Power
LED is off, chec the main power input. When this does not solve the problem,
please call service first and then open DST5-RDM and chec fuses on the main
board.
When the DMX cable is connected to the device, LEDs mar ed as D+ and D- go
on for the side mar ed as DMX input, thru and this indicates that DST5-RDM is
receiving the DMX signal. Speed of light on these LEDs also indicates the
refresh rate of DMX signal. Fast blin ing – high refresh rate, slow blin ing – slow
refresh rate.
On the front panel of DST5-RDM, there are outputs A-E, which are retransmitting
the input to the optically isolated outputs. If any of data LEDs is off, unplug the
signal cable corresponding to this output and chec the cable for short circuit
between D+ and CMN or D- and CMD lines.
RDM filter switch will filter all RDM commands from the DMX stream.
In case of any problems, do not hesitate to contact us via email at
[email protected] or call us at [phone]. Don’t worry; we will fix your
problems for sure.

( 4 / 4)
Technical data
Main in ut:
AC 100-255V / 50-60Hz / 5W
DMX In ut / Out ut:
5x USITT DMX512 with RDM support isolated up to 1000V
Maximum of: 5x 32 devices per one splitter output
Cable length: max: 5x 1200m
Housing/Size:
Lightweight Aluminum box with powder coating
230x155x50mm
Mounting oints:
Wall-mount ears on both sides of splitter
4 rubber feet on the bottom of device
DECLARATION OF CONFORMITY
According to the guidelines 89/336 EEC and 92/31 EEC:
Name of roducer: SRS Group s.r.o.
Address of roducer: Rybnicna 36/D, SK- 83106 Bratislava, Slova Republic
Declares that the product
Name of roduct: DST5-RDM 5-way DMX/RDM splitter
Ty e: DST5-RDM
Corresponds to the following product specifications:
Safety: EN60065, resp. EN 60950
EMC: EN55103-1, resp. EN55103-2
Bratislava, 2 November 2014
Robert Sloboda
Copyright 2017 SRS Group, s.r.o. | Specifications subject to change without notice.
Document: DST5-RDM_en_manual_M087 | Version 1.0 | Actual as of: 3 February 2020
SRS Grou s.r.o.
Rybnicna 38/B | 831 07 Bratislava | Slova ia
Phone: [phone]
Email: [e-mail] | www.srs-group.com
Weight:
1.2 g
Tem erature of use:
-10 ºC … +45 º C
Warranty:
Life-time warranty