EtherWAN EMC1200R User manual

W70G-EMC1200rQ1 Page 1
Installation Guide
EMC1200r | 12-Bay Media Converter System
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/28/2023
1Unpacking
Open the carton and unpack the items. Your package
should include:
▪One 12-Bay Media Converter System
▪Two AC power cords
▪Rackmount ears with screws
If any items are missing or damaged, notify your
EtherWAN representative.
2Select a Location
The installation site should be free of extreme
temperatures, humidity, or excessive electromagnetic
interference. Specifically, the site should meet the
following requirements:
▪The ambient temperature should be between 0
and 45 degrees Celsius (32 to 113 degrees
Fahrenheit).
▪The relative humidity should be at least 5% and
less than 95 percent, non-condensing.
▪Surrounding electrical devices should not exceed
the electromagnetic field (RFC) standards for IEC
801-3, Level 2 (3V/M) field strength.
▪Make sure that the equipment receives adequate
ventilation.
▪Do not block the ventilation holes on each side of
the equipment or the fan exhaust port on the side
or rear of the equipment.
▪The power outlet should be within 6 feet (1.8
meters) of the equipment.
3Connect Power
Power supply is via redundant 12VDC terminal block
power inputs. However, only one power supply is
needed to operate the chassis.
▪Connect the supplied AC power cords to the
receptacles on the rear panel of the system.
▪Attach the plugs from each of the dual power
supplies into standard AC outlets with a voltage
range from 100~240VAC.
▪Turn on the system by flipping the ON/OFF
switches beside the dual power supplies’
receptacles to the ON position.
▪The power LED of each media converter will light
up after turning on the system.
▪The link LED of each media converter will light up
after connecting twisted pair copper cabling
between the TX port (or fiber optic
▪cabling between the FX port) and another working
networked device.
4Status LEDs
There are 12 sets of LED indicators, which provide
instant feedback on the status of each media
converter channel.
10/100TX to 100FX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
100 (Mbps)
Steady
Connection at 100Mbps
Off
Connection at 10Mbps
LNK/ACT
Steady
Valid network connection
established
Flashing
Transmitting or receiving
data
Off
No valid network connection
or data transmission
FDX/COL
Steady
Connection in full duplex
mode
Flashing
Collision occurred
Off
Connection in half-duplex
mode
100TX to 100FX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
LNK
Steady
Connection at 100Mbps
Off
No connection at 100Mbps
ACT
Steady
Valid network connection
established
Flashing
Transmitting or receiving
data
Off
No valid network connection
or data transmission

W70G-EMC1200rQ1 Page 2
Installation Guide
EMC1200r | 12-Bay Media Converter System
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 03/28/2023
100FX to 100FX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
SDA/ SDB
(100FX)
Steady
Valid network connection
established, data
transmission
Off
No valid network connection
or data transmission
10/100/1000TX to 1000SX/LX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
LNK/ACT
(TX)
Steady
Valid network connection
established
Flashing
Transmitting or receiving
data
Off
No connection or data
transmission
LNK/ACT
(SX/LX))
Steady
Valid network connection
established
Flashing
Transmitting or receiving
data
Off
No connection or data
transmission
FDX/COL
Steady
Connection in full duplex
mode
Flashing
Collision occurred
Off
Connection in half-duplex
mode
1000
Steady
Connection at 1000Mbps
100
Steady
Connection at 100Mbps
1000, 100
Off
Connection at 10Mbps
1000T to 1000SX/LX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
LNKC
Steady
TX Port: Valid network
connection established
Off
No connection
LNKF
Steady
FX Port: Valid network
connection established
Off
No connection
FDX/COL
Steady
Connection in full duplex
mode
RX
Steady
Receiving data
Off
No data reception
TX
Steady
Transmitting data
Off
No data transmission
1000SX/LX to 1000SX/LX Media Converter
LED
State
Indication
PWR
Steady
Power on
Off
Power off
SDA
Steady
Port A signal detect: Valid
network connection
established
Off
No connection
SDB
Steady
Port B signal detect: Valid
network connection
established
Off
No connection
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com