SST Automation GT200-MT-DN User manual

Modbus TCP / DeviceNet Gateway
GT200-MT-DN
User Manual
V 2.0
Rev A
SST Automation
Email: [e-mail]
[e-mail]
WWW.SSTAUTOMATION.COM
WWW.SSTCOMM.COM

WWW.SSTAUTOMATION.COM
Important Information
Warning
The data and examples in this manual cannot be copied without authorization. SSTCOMM reserves the right to
upgrade the product without notifying users.
The product has many applications. The users must make sure that all operations and results are in accordance
with the safety of relevant fields, and the safety includes laws, rules, codes and standards.
Copyright
Copyright © 2022 by SST Automation. All rights reserved.
Trademark
is the registered trade mark of SST Automation.
Technical Support Contact Information
www.sstautomation.com
E-mail: [e-mail]

WWW.SSTAUTOMATION.COM
Catalog
1 Product Overview ......................................................................................................................................................1
1.1 Product Function ............................................................................................................................................ 1
1.2 Product Feature ...............................................................................................................................................1
1.3 Technical Specifications .................................................................................................................................2
1.4 Revision History .............................................................................................................................................3
2 Hardware Descriptions .............................................................................................................................................. 4
2.1 Product Appearance ........................................................................................................................................4
2.2 LED Indicators ............................................................................................................................................... 5
2.3 Configuration Switch/Button ......................................................................................................................... 6
2.4 Interface .......................................................................................................................................................... 6
2.4.1 DeviceNet Interface ............................................................................................................................ 6
2.4.2 Ethernet Interface ................................................................................................................................ 7
3 Hardware Installation ................................................................................................................................................ 8
3.1 Mechanical Dimensions ................................................................................................................................. 8
3.2 Installation Method ........................................................................................................................................ 8
4 Quick Start Guide ...................................................................................................................................................... 9
4.1 Hardware Connection .....................................................................................................................................9
4.2 Communication Debugging ........................................................................................................................... 9
5 SST-DNET-COM Software Instructions .................................................................................................................10
5.1 Notes Before Configuration ......................................................................................................................... 10
5.2 Software Main Interface ...............................................................................................................................10
5.3 Toolbar ..........................................................................................................................................................12
5.4 DeviceNet Device Network Configuration ..................................................................................................12
5.5 DeviceNet Network Scanning ......................................................................................................................21
5.6 Equipment Parameter Modification and I/O Data Test ................................................................................22
6 Working Principle ....................................................................................................................................................40
6.1 Data Exchange ..............................................................................................................................................40
6.2 Terminating Resistor .................................................................................................................................... 40
7 DeviceNet Network Configuration Instructions (DeviceNet Adapter) .................................................................. 41
7.1 I/O Configuration ......................................................................................................................................... 41
7.2 DeviceNet Parameters .................................................................................................................................. 41

WWW.SSTAUTOMATION.COM
1
1 Product Overview
1.1 Product Function
The product can realize the data exchange with DeviceNet network through Modbus TCP. It supports connecting
devices with DeviceNet interface to Modbus TCP network. This module is a server on the Modbus TCP side and a
scanner or adapter on the DeviceNet side.
1.2 Product Feature
DeviceNet Scanner: Supports connecting up to 8 DeviceNet devices to Modbus TCP network, such as:
Robots with DeviceNet interfaces, inverters, welder, motor starting protection devices, intelligent field
measurement equipment, etc.
DeviceNet adapter: Supports data exchange between DeviceNet scanner and Modbus TCP master, such as:
data exchange between robots, welder, PLCs and other devices with DeviceNet scanner interface and the host
computer.
Users don't need to know the technical details of Modbus TCP and DeviceNet, only refer to this manual and
the application cases provided, complete configuration according to requirements, the network can be
connected in a short time.
Transparent communication: According to the mapping relationship between Modbus TCP communication
data area and DeviceNet communication data area, users can realize data transparent communication between
DeviceNet network and Modbus TCP network.
Professional and efficient configuration software SST-DNET-COM: The gateway can scan DeviceNet
adapters online through this software, quickly obtain its I/O parameters and configure parameters, support
online debugging, support offline upload and download, offline configuration, and support DeviceNet
scanner/adapter mode switch.

WWW.SSTAUTOMATION.COM
2
1.3 Technical Specifications
[1] Ethernet interface:
● Supports 2 10M/100M adaptive network ports with build-in switch.
● Supports Modbus TCP protocol, the Ethernet interface can be configured as a Modbus TCP server.
● Supports function codes:03H, 04H, 06H, 10H.
● The starting address of the input register is 0 (stores the received CAN frame), and support the function
code 04H.
● The starting address of the output register is 0 (stores the CAN frames that need to be sent), and support
the function codes 03H, 06H and 16H.
● Supports static configuration of IP address and DHCP.
[2] DeviceNet interface:
DeviceNet supports two working modes: scanner station and adapter station. DeviceNet scanner station
supports pre-operation mode and operation mode
[3] As DeviceNet Scanner - Pre-operation mode (Configuration switch 1-ON, 2-OFF)
● Supports device search, namely online scanning DeviceNet adapter through SST-DNET-COM software.
● Supports one-click application of the scanned DeviceNet adapter I/O parameter configuration, and
reading and writing configuration through SST-DNET-COM software.
● Supports reading and writing DeviceNet adapter parameters.
● Supports reading and writing DeviceNet I/O data(polling).
● Supports reading cos commands (COS) (up to 14 bytes).
● Supports DeviceNet baud rate: 125K, 250K, 500K.
● Supports reading and writing product information.
[4] As DeviceNet Scanner - Operation mode (Configuration switch 1-OFF, DIP2-OFF)
● Supports communication with Modbus TCP network.
● The Maximum number of input and output bytes supported by single DeviceNet adapter: 128 byte and
112 bytes.
● The maximum number of input/output bytes supported by DeviceNet adapter: 512 bytes.

WWW.SSTAUTOMATION.COM
3
● Supports connecting up to 8 adapter devices, and input timeout clearing and holding function of
DeviceNet (optional).
● Supports reading cos commands (COS) (up to 14 bytes).
● Supports DeviceNet baud rate: 125K, 250K, 500K.
[5] As DeviceNet Adapter
● DeviceNet supports up to 224 bytes of input or output, 8, 16, 32, 96, 48, 64, 112, 72, 160, 192 and 224
bytes.
● The module is powered from the DeviceNet network, and the power supply voltage is DC 11~30V.
● Supports DeviceNet I/O Poll scanning.
● Supports DeviceNet baud rate: 125K, 250K and 500K.
[6] Operating temperature: -40 °F~140 °F(-20 °C to 50 °C). Relative Humidity: 5% to 95% (non-condensing)
[7] Power: 24VDC (11V~30V), maximum 80mA (24V).
[8] Built-in electrostatic protection: 15 KV ESD.
[9] External dimensions (W*H*D): 1.0 in*4.0 in *3.6in (25mm*100mm*90mm).
[7] Installation : 35mm DIN RAIL.
[10] Protection level: IP20.
[11] Pollution level: class 3.
1.4 Revision History
Revision
Date
Chapter
Description
V2.0
04/02/2021
ALL
New Release
V2.0 Rev A
07/25/2022
PART
New DeviceNet modeling
software SST-DNET-COM

WWW.SSTAUTOMATION.COM
4
2 Hardware Descriptions
2.1 Product Appearance
Notes: This picture is for reference only. The product appearance is subject to the actual product.
DeviceNet Interface
Ethernet Interface
Indicators
Configuration Switch

WWW.SSTAUTOMATION.COM
5
2.2 LED Indicators
Indicators
Status
Description
ENS
(Ethernet Status Indicator)
Green
Modbus TCP connection is established
Green Blinking
Modbus TCP connection is not established
Red Blinking
DHCP
Red Blinking twice
Power-on initialization state
MNS
（DeviceNet Scanner -
Pre-operation mode）
OFF
Initialization completed. searching not started yet
Green blinking
The scanner is online, but no connection has been
established with the adapter
Green
Connected with the adapter
Red Blinking
Disconnected with the adapter
MNS
（DeviceNet Scanner -
Operation mode）
Off
Module is running and initialization has not yet been
completed
Green Blinking
Initialization completed, The scanner is online, but no
connection has been established with the adapter
Green
Connected with the adapter
Red Blinking
Disconnected with the adapter
Red
There is no adapter on CAN network. Detected
address confliction, CAN network error (like baud
rate error)
MNS
（DeviceNet Adapter）
Red
DeviceNet network error
Red/Green
Blinking
DeviceNet initialization
Green Blinking
DeviceNet connection is establishing
Green
DeviceNet network is normal
ENS Orange MNS Orange
(Orange：Red/Green is on
simultaneously)
Blinking alternately
Configuration mode
ENS Red MNS Red
Blinking 3 times
simultaneously
Locating
Note: Configuration status: After power on, the orange blinks alternately, indicating that it is in the configuration
status.

WWW.SSTAUTOMATION.COM
6
2.3 Configuration Switch/Button
The Configuration switch is used to set the operating mode of the GT200-MT-DN.
Off
On 1 2
Mode
(Bit 1)
Function
(Bit 2)
Description
OFF
OFF
● As DeviceNet scanner - Operation mode.
● As DeviceNet adapter - Operation mode and allows remote
configuration.
ON
OFF
● As DeviceNet scanner - Pre-operation mode.
● As DeviceNet adapter - Operation mode and prohibits remote
configuration, effective in operation mode.
OFF
ON
Configuration mode, the IP address is fixed at 192.168.0.10. Users can
only read and write configuration data, and operation is prohibited.
ON
ON
Enter the factory setting mode (forbidden to use by customers)
Notes:
1. To apply the mode switching, please restart the gateway.
2. When the GT200-MT-DN works as DeviceNet adapter, after finishing configuration, it’s recommended to set
the switch to 1-ON 2-OFF, which is the configuration mode that configuration in operation mode.
2.4 Interface
2.4.1 DeviceNet Interface
V+
GND
CAN_L
SHIELD
CAN_H
1
5
Note: The GT200-MT-DN is powered in DeviceNet interface.
Pin
Description
1
GND
2
CAN-
3
shield
4
CAN+
5
+24V

WWW.SSTAUTOMATION.COM
7
2.4.2 Ethernet Interface
The Ethernet interface uses RJ45 interface, follows the IEEE802.3u 100BASE-T standard, 10/100M adaptive,. its
pin (standard Ethernet signal) is defined as below:
Pin
Description
S1
TXD+, Transmit Data+, Output
S2
TXD-, Transmit Data-, Output
S3
RXD+, Receive Data+, Input
S4
Bi-directional Data+
S5
Bi-directional Data-
S6
RXD-, Receive Data-
S7
Bi-directional Data+
S8
Bi-directional Data-

WWW.SSTAUTOMATION.COM
8
3 Hardware Installation
3.1 Mechanical Dimensions
Size (width * height * depth):
1.0 in * 4.0 in * 3.6 in (25 mm * 100 mm * 90 mm)
3.2 Installation Method
Using 35mm DIN RAIL.

WWW.SSTAUTOMATION.COM
9
4 Quick Start Guide
4.1 Hardware Connection
1. According to the instructions of the RJ-45 port in Chapter 2, correctly connect the corresponding wiring of
each pin of the RJ-45.
2. According to the instructions of the DeviceNet port in Chapter 2, connect the wiring correctly, and note that
it is not suitable to power on at this time.
3. Check whether the wiring conforms to the instructions of the manual.
4. Power on the module and it will enter the running state.
4.2 Communication Debugging
1. The default configuration of GT200-MT-DN is DeviceNet scanner mode, the DIP switches are all OFF, and
the default IP address is 192.168.0.X. Users can change the operating mode according to the actual
application.
2. The gateway uses the network port connection configuration, please refer to Chapter 5 of the manual for
details.
3. After the GT200-MT-DN configuration is completed, install GT200-MT-DN on the standard rail frame,
power on and use.

WWW.SSTAUTOMATION.COM
10
5 SST-DNET-COM Software Instructions
5.1 Notes Before Configuration
When the DIP of GT200-MT-DN is "1ON 2OFF", the gateway is in operation mode, and the I/O parameters of the
adapter devices on the DeviceNet network can be configured through SST-DNET-COM software.
DeviceNet network configuration software SST-DNET-COM is developed by SST Automation. It needs to be
used with SSTCOMM's GT200-MT-DN or other DeviceNet scanner modules.
The following introduction is aimed at helping you get quickly started for using our gateway. More details about
using software, please refer to "Help"->"Content" in the SST-DNET-COM software.
5.2 Software Main Interface
For the first time to use the SST-DNET-COM software, it requires activation code.
Click “Get Activation Code” and it will jump to sstautomation.com for activation.

WWW.SSTAUTOMATION.COM
11
You can access SST-DNET-COM software after entering correct activation code.
Configuration window: After establishing the internet connection, display the online device and modify the
address and parameters of the device online,check the input and output data.In the offline state, you can view
device properties by dragging the device icon to the window.
Tree View: Displays registered DeviceNet devices in different ways: device type, manufacture. Under different
manufacturers, different devices are displayed separately according to the device type.
Comment Interface: Dynamic display of network scanning information, registered device information, delete
device information, etc. display the results of "find devices", "find next".
Menu Bar
Title Bar
Configuration Window
Toolbar
Tree View
Comment Interface

WWW.SSTAUTOMATION.COM
12
5.3 Toolbar
Toolbar is shown as below:
Functions separately from left to right are: New, Open, Save, Print, Cut, Copy, Paste, Refresh viewport, EDS
Wizard, Find devices in the device library, find next, Internet Connection, One-Click Save, Disconnect, Configure,
Send Explicit Message, Property, Device Management, Output.
5.4 DeviceNet Device Network Configuration
EDS Registration Wizard
Users can configure different DeviceNet devices by registering new EDS files. Register the new EDS file, select
"Tools" -> "EDS wizard", or click "EDS wizard" button in the toolbar. Or directly click the right button in the
Equipment management window and select "EDS wizard" which will pop up the EDS wizard interface. The three
ways are as follows:

WWW.SSTAUTOMATION.COM
13
EDS wizard interface is shown in the following figure:
Select "Start "and pop up the following interface:
In this interface, users can choose to register an EDS file, log out of an existing device, and change the icon of a
device.
Take "Register an EDS file" as an example to introduce the following steps for registering a new EDS file:
After selecting "Register an EDS file", click "Next step" and select the storage path of EDS file you want to
register in the pop-up interface, as shown in the figure below:

WWW.SSTAUTOMATION.COM
14
Click "Next step" to pop up the EDS file test report interface. If there is an error in the EDS file, the error message
will be displayed in the interface, and there is no "Next step" operation. If there is no error in the file, continue the
"Next step" operation, pop-up selection device icon interface as follows:

WWW.SSTAUTOMATION.COM
15
After selecting a device icon, click "next step" to pop up the factory information of the registered device, as shown
in the figure below:
Click "Finish" and the EDS file registration step is over. At this time, you can see the newly registered device in
the equipment Management Window.
If you want to change EDS file for the same device, please first find the device in the device management library
and right click. After logging out, re-register the new EDS file, or complete the logout operation through the EDS
operation.
PC-DeviceNet Interface Setting

WWW.SSTAUTOMATION.COM
16
SST-DNET-COM software needs to be used together with the DeviceNet scanner module. First, connect
GT200-MT-DN to Ethernet, and then connect GT200-MT-DN's DeviceNet port and user's DeviceNet device to
the DeviceNet network. Power Supply of GT200-MT-DN is 24VDC.
Power on After correctly Connecting to Power Supply, the connection of DeviceNet network can be established by
"Internet Connection" in the menu bar or toolbar.Click "Internet Connection" and pop up the path selection
interface:
Then click the interface setting, the software will display the searched device in the list, select the scanner station
to be configured for the interface setting:

WWW.SSTAUTOMATION.COM
17
At default, the GT200-MT-DN act as a DeviceNet adapter mode. Please change to the scanner mode if you want
to use it as a DeviceNet scanner mode.
Firstly, upload the gateway by right clicking the blank area.
Double click the module,