Digi ConnectPort X4 H User manual

Distributor of Digi International: Excellent Integrated System Limited
Datasheet of X4H-Z1U-B101-US - ROUTING GATEWAY X4 H ZB-ETH/CELL
Contact us: [email protected] Website: www.integrated-circuit.com
Excellent Integrated System Limited
Excellent Integrated System Limited
Stocking Distributor
Stocking Distributor
Click to view price, real time Inventory, Delivery & Lifecycle Information:
Click to view price, real time Inventory, Delivery & Lifecycle Information:
Digi International
Digi International
X4H-Z1U-B101-US
X4H-Z1U-B101-US
For any questions, you can email us directly:
For any questions, you can email us directly:
[email protected]
[email protected]
1 / 3
1 / 3

Distributor of Digi International: Excellent Integrated System Limited
Datasheet of X4H-Z1U-B101-US - ROUTING GATEWAY X4 H ZB-ETH/CELL
Contact us: [email protected] Website: www.integrated-circuit.com
ConnectPort
X4
H
a
b
1Verify Contents
Cellular/ WiMAX Antenna
2
Ethernet Cable
Quick Start Guide
ConnectPort™X4 H
Open Device
aUnscrew and open the lid. Be sure to note that the top of the
enclosure is hinged to the base on the power cord side.
ConnectPort X4 H
Not included: If your device uses a SIM card,
it must be supplied and activated by a
cellular service provider for device operation.
90000978_D
X4-xxx-Y-xxx-xx
All other models
Part Number
2
1
# of Antennas
[GSM models only] Insert SIM card as shown.
bConnect one end of the Ethernet cable to the ConnectPort X4 H
and the other end to a PC.
a
3Install SIM/Ethernet
NOTE: The primary SIM Card should be installed in the upper
SIM slot, and the contacts should be face down. In the lower
slot, the contacts should be face up. In both cases, the end of
the SIM card with the chamfered corner should be inserted rst.
4
a
Connect the cellular antenna
b
Connect the XBee antenna.
Connect Hardware
NOTE: If you have a WiMAX model (X4-xxx-Yxxx-xx),
connect the two WiMAX antennas to your unit instead of the
cellular antenna depicted.
cPower-up the unit by connecting the AC power
cord to a proper power source.
dOnce you have connected all the hardware, please refer to the ConnectPort X4
Getting Started Guide to congure the unit. This guide can be
downloaded at www.digi.com/connectportx4. Once congured, refer to
Step 5 to nalize the unit.
NOTE: If you have a Class 1 Div 2 model that requires hard-wiring a
power source to the unit, see the "ConnectPort™ X Family User’s Guide"
for wiring instructions, which can be found by clicking the link located
in step D.
ConnectPort
X4
H
ConnectPort
X4
H
b
Primary
Secondary
Shift
XBee
Antenna
The information listed below is meant to help aid you in identifying the
accessories included in your box. You may need to reference the product
part number (X4-xxx-xxx-x) which is located on the Digi label on the
outside of the box.
a
2 / 3
2 / 3

Distributor of Digi International: Excellent Integrated System Limited
Datasheet of X4H-Z1U-B101-US - ROUTING GATEWAY X4 H ZB-ETH/CELL
Contact us: [email protected] Website: www.integrated-circuit.com
© 2012 Digi International, Inc.
Digi, Digi International, Inc., Digi Connect, ConnectPort and the Digi logo are trademarks or registered trademarks of Digi International, Inc., in the United States and other countries worldwide. All other trademarks are property of their respective owners.
bRemove the Ethernet cable and replace the screws that were removed in Step 2.
cThe unit now ready to use. Restore power to the unit by reconnecting it to the power source.
Remove power from the unit by disconnecting it from the power source.
a
5Finalize Unit
Powered by TCPDF (www.tcpdf.org)
Powered by TCPDF (www.tcpdf.org) 3 / 3
3 / 3