Standard Pump SPFP20 Parts list manual

Standard Pump
SPFP20 Models
• SPFP20NPT
• SPFP20NPS
• SPFP20SSS
• SPFP20SST
• SPFP20NPP
• SPFP20SSP
2" Food Processing
with Metallic Center Section
SPFP20
STANDARD PUMP, INC®
1610 Satellite Blvd Suite D. Duluth, Ga. 30097 • Phone: [phone] • www.standardpump.com
THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE
WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC.
DESCRIPTION
DRAWING NUMBER
WARREN RUPP INC.
REV
02
E2SJxxxx9C-FP-ATEX
E2 FOOD PRO HYTREL FITTED
PUMP
Service & Operating Manual
1: PUMP SPECS2: INSTAL & OP3: EXP VIEW4: CERTIFICATES
Original Instructions

spfp20sm-rev0516
www.standardpump.com
IMPORTANT
Read the safety warnings and instructions in this manual
before pump installation and start-up. Failure to comply with
the recommendations stated in this manual could damage the
pump and void factory warranty.
When used for toxic or aggressive uids, the pump should
always be ushed clean prior to disassembly.
Airborne particles and loud noise hazards. Wear eye and ear
protection.
Before maintenance or repair, shut off the compressed air line,
bleed the pressure, and disconnect the air line from the pump.
Be certain that approved eye protection and protective clothing
are worn at all times. Failure to follow these recommendations
may result in serious injury or death.
To be fully groundable, the pumps must be ATEX Compliant.
Optional 8 foot long (244 centimeters) Ground Strap is available for easy ground connection.
To reduce the risk of static electrical sparking, this pump must be grounded. Check the local
electrical code for detailed grounding instruction and the type of equipment required.
When the pump is used for materials that tend to settle out
or solidify, the pump should be ushed after each use to
prevent damage. In freezing temperatures the pump should be
completely drained between uses.
Before pump operation, inspect all fasteners for loosening
caused by gasket creep. Retighten loose fasteners to prevent
leakage. Follow recommended torques stated in this manual.
CAUTION
WARNING
Nonmetallic pumps and plastic components are not UV
stabilized. Ultraviolet radiation can damage these parts and
negatively affect material properties. Do not expose to UV light
for extended periods of time.
In the event of diaphragm rupture, pumped material may enter
the air end of the pump, and be discharged into the atmosphere.
If pumping a product that is hazardous or toxic, the air exhaust
must be piped to an appropriate area for safe containment.
This pump is pressurized internally with air pressure during
operation. Make certain that all fasteners are in good condition
and are reinstalled properly during reassembly.
Take action to prevent static sparking. Fire or explosion can
result, especially when handling ammable liquids. The pump,
piping, valves, containers and other miscellaneous equipment
must be properly grounded.
Safety Information
Grounding the Pump
WARNING
Take action to prevent static sparking.
Fire or explosion can result, especially
when handling ammable liquids. The
pump, piping, valves, containers or
other miscellaneous equipment must
be grounded.
WARNING
Pump not designed, tested or certied to be powered by
compressed natural gas. Powering the pump with natural
gas will void the warranty.
Use safe practices when lifting
kg
UNIVERSAL ALL AODD

spfp20sm-rev0516 www.standardpump.com
Table of Contents
SECTION 1: PUMP SPECIFICATIONS................1
• Performance
• Materials
• Dimensional Drawings
SECTION 2: INSTALLATION & OPERATION......4
• Principle of Pump Operation
• Typical Installation Guide
• Troubleshooting
SECTION 3: EXPLODED VIEW...........................7
• Composite Drawings
• Parts List
• Materials Code
SECTION 4: CERTIFICATES ............................11
• EC Declaration of Conformity - Directive 2006/42/EC - Machinery
• EC Declaration of Conformity - Directive 94/9/EC - ATEX
• EC Declaration of Conformity - Directive 1935/2004/EC - Food Contact Materials
Universal*
1: PUMP SPECS2: INSTAL & OP3: EXP VIEW4:CERTIFICATES

spfp20sm-rev0516
1• Model SPFP20 Food Processing
www.standardpump.com
Performance
Model SPFP20NPS & SPFP20SSS
2” Food Processing
FDA SANTOPRENE FITTED
Flow Rate
Adjustable to ....... 0-185 gpm (700 lpm)
Port Size
Suction ................. 2½" Tri-Clamp
Discharge............... 2½" Tri-Clamp
Air Inlet ......................1/2" NPT
Air Exhaust ................... 1" NPT
Suction Lift
Dry ........................17' (5.1 m)
Wet........................32' (9.5 m)
Max Solid Size (Diameter)
........................1/4" (7.6 mm)
Max Noise Level .............96 dB(A)
Shipping Weights
Stainless...............106 lbs (48.1 kg)
Model SPFP20NPT & SPFP20SST
2” Food Processing
PTFE FITTED
Flow Rate
Adjustable to ....... 0-153 gpm (579 lpm)
Port Size
Suction ................. 2½" Tri-Clamp
Discharge............... 2½" Tri-Clamp
Air Inlet ......................1/2" NPT
Air Exhaust ................... 1" NPT
Suction Lift
Dry ........................11' (3.3 m)
Wet........................29' (8.8 m)
Max Solid Size (Diameter)
........................1/4" (7.6 mm)
Max Noise Level ............102 dB(A)
Shipping Weights
Stainless...............106 lbs (48.1 kg)
NOTE: Performance based on the following: PTFE tted pump, ooded suction, water at ambient
conditions. The use of other materials and varying hydraulic conditions may result in deviations in
excess of 5%.
NOTE: Performance based on the following: elastomeric tted pump, ooded suction, water at ambient
conditions. The use of other materials and varying hydraulic conditions may result in deviations in
excess of 5%.
Discharge Head in PSI
0 75 150 225 300 375 450 525 600 675 750
140
120
100
80
60
40
20
0
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.60 Gal. (2.3 L)
AIR CONSUMPTION IN SCFM
AIR PRESSURE IN PSI
SCFM M3/HR
10 17
20 34
40 51
60 102
80 136
100 170
120 204
0 20
10 20 40 60
80
100
120
140
40 60 80 100 120 140 160 180 200
Meters Feet
00
40
80
120
160
200
240
280
10
20
30
40
50
60
80
90
70
0
1
2
3
4
5
6
7
8
9
10
BAR
Discharge Head in PSI
140
120
100
80
60
40
20
0
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Capacity Per Stroke, 0.35 Gal. (1.3 L)
AIR CONSUMPTION IN SCFM
AIR PRESSURE IN PSI
SCFM M3/HR
10 17
20 34
40 51
60 102
80 136
100 170
120 204
0 20
10 20 40 60 80
100
120
140
40 60 80 100 120 140 160 180
075 150 225 300 375 450 525 600 675
Meters Feet
00
40
80
120
160
200
240
280
10
20
30
40
50
60
80
90
70
0
1
2
3
4
5
6
7
8
9
10
BAR
1: PUMP SPECS

spfp20sm-rev0516
Model SPFP20 Food Processing • 2
www.standardpump.com
Materials
Material Prole: Operating
Temperatures:
Max. Min.
Santoprene®: Injection molded thermoplastic elastomer with
no fabric layer. Long mechanical ex life. Excellent abrasion
resistance.
275°F
135°C
-40°F
-40°C
Virgin PTFE: (PFA/TFE) Chemically inert, virtually impervious.
Very few chemicals are known to chemically react with PTFE;
molten alkali metals, turbulent liquid or gaseous uorine and
a few uoro-chemicals such as chlorine triuoride or oxygen
diuoride which readily liberate free uorine at elevated
temperatures.
220°F
104°C
-35°F
-37°C
Maximum and Minimum Temperatures are the limits for which these materials can be operated.
Temperatures coupled with pressure affect the longevity of diaphragm pump components.
Maximum life should not be expected at the extreme limits of the temperature ranges.
Metals:
Stainless Steel: Equal to or exceeding ASTM specication A743 CF-8M for corrosion
resistant iron chromium, iron chromium nickel and nickel based alloy castings for
general applicaitons. Commonly referred to as 316 Stainless Steel in the pump industry.
CAUTION! Operating temperature limitations are as follows:
1: PUMP SPECS

spfp20sm-rev0516
3• Model SPFP20 Food Processing
www.standardpump.com
Model SPFP20 Food Processing
Dimensions in inches (mm dimensions in brackets)
The dimensions on this drawing are for reference only. A certied drawing can be requested if physical dimensions are needed.
Dimensional Drawings
17.18
436.32 3.03
76.96
O.D. TRI-CLAMP
DISCHARGE PORT
1.72
43.64 3.03
76.96
O.D. TRI-CLAMP
SUCTION PORT
9.39
238.48
19.42
493.34
24.72
627.86
1.00
25.40
RUBBER FOOT
1/2" NPT
AIR INLET
1" NPT
AIR EXHAUST
26.22
665.96
.38
9.53
3.00
76.20
13.62
345.95
9.00
228.60
10.00
254.00
12.50
317.50
11.50
292.10
2.50
63.50
RUBBER FOOT
Model Specic
1: PUMP SPECS

spfp20sm-rev0516
Model SPFP20 Food Processing • 4
www.standardpump.com
Air-Operated Double Diaphragm (AODD) pumps are powered
by compressed air or nitrogen.
The main directional (air) control valve ①distributes
compressed air to an air chamber, exerting uniform pressure
over the inner surface of the diaphragm
②. At the same time,
the exhausting air ③ from behind the opposite diaphragm
is directed through the air valve assembly(s) to an exhaust
port ④.
As inner chamber pressure (P1) exceeds liquid chamber
pressure (P2), the rod ⑤connected diaphragms shift
together creating discharge on one side and suction on the
opposite side. The discharged and primed liquid’s directions
are controlled by the check valves (ball or ap)⑥orientation.
The pump primes as a result of the suction stroke. The
suction stroke lowers the chamber pressure (P3) increasing
the chamber volume. This results in a pressure differential
necessary for atmospheric pressure (P4) to push the uid
through the suction piping and across the suction side check
valve and into the outer uid chamber ⑦.
Suction (side) stroking also initiates the reciprocating
(shifting, stroking or cycling) action of the pump. The suction
diaphragm’s movement is mechanically pulled through its
stroke. The diaphragm’s inner plate makes contact with an
actuator plunger aligned to shift the pilot signaling valve.
Once actuated, the pilot valve sends a pressure signal to the
opposite end of the main directional air valve, redirecting the
compressed air to the opposite inner chamber.
Principle of Pump Operation
SAFE AIR
EXHAUST
DISPOSAL
AREA
PUMP INSTALLATION AREA
1" DIAMETER AIR
EXHAUST PIPING
1" DIAMETER AIR
EXHAUST PIPING
1" DIAMETER AIR
EXHAUST PIPING
MUFFLER
LIQUID
LEVEL
SUCTION
LINE
LIQUID
LEVEL
SUCTION
LINE
MUFFLER
MUFFLER
SUBMERGED ILLUSTRATION
Pump can be submerged if the pump materials of construction
are compatible with the liquid being pumped. The air exhaust
must be piped above the liquid level. When the pumped product
source is at a higher level than the pump (ooded suction
condition), pipe the exhaust higher than the product source to
prevent siphoning spills.
MODEL SPECIFIC
Air Line
Discharged
Fluid
Discharge
Stroke Suction
Stroke
Primed
Fluid
2: INSTAL & OP

spfp20sm-rev0516
5• Model SPFP20 Food Processing
www.standardpump.com
Installation And Start-Up
Locate the pump as close to the product being pumped as possible. Keep the suction line length and number of ttings to a minimum. Do not reduce the suction line
diameter.
Air Supply
Connect the pump air inlet to an air supply with sufcient capacity and pressure to achieve desired performance. A pressure regulating valve should be installed to
insure air supply pressure does not exceed recommended limits.
Air Valve Lubrication
The air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricator
set to deliver one drop of SAE 10 non-detergent oil for every 20 SCFM (9.4 liters/sec.) of air the pump consumes. Consult the Performance Curve to determine air
consumption.
Air Line Moisture
Water in the compressed air supply may cause icing or freezing of the exhaust air, causing the pump to cycle erratically or stop operating. Water in the air supply can
be reduced by using a point-of-use air dryer.
Air Inlet And Priming
To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air ow as desired. If opening the valve
increases cycling rate, but does not increase the rate of ow, cavitation has occurred. The valve should be closed slightly to obtain the most efcient air ow to pump
ow ratio.
Surge Suppressor
Shut-Off Valve
Pressure Gauge
Drain Port
Shut-Off
Valve
Check
Valve
Air Inlet
Discharge
Unregulated Air
Supply to Surge
Suppressor
Pipe Connection
(Style Optional)
Flexible Connector
Flexible Connector
Vacuum
Gauge
Suction
Shut-Off Valve
Drain Port Pipe Connection
(Style Optional)
Flexible
Connector
Air Dryer
Filter Regulator
P/N: 020.V107.000
Note: Pipe weight should not be supported
by pump connections.
Muffler
(Optional Piped Exhaust)
Recommended Installation Guide
Available Accessories:
1. Surge Suppressor
2. Filter/Regulator
3. Air Dryer
1
2
3
Note: Surge Suppressor and
Piping must be supported after
the exible connection.
CAUTION
The air exhaust should
be piped to an area
for safe disposition
of the product being
pumped, in the event of
a diaphragm failure.
UNIVERSAL ALL AODD
2: INSTAL & OP

spfp20sm-rev0516
Model SPFP20 Food Processing • 6
www.standardpump.com
Recommended Installation Guide Troubleshooting Guide
Symptom: Potential Cause(s): Recommendation(s):
Pump Cycles Once Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Air valve or intermediate gaskets installed incorrectly. Install gaskets with holes properly aligned.
Bent or missing actuator plunger. Remove pilot valve and inspect actuator plungers.
Pump Will Not Operate
/ Cycle
Pump is over lubricated. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Lack of air (line size, PSI, CFM). Check the air line size and length, compressor capacity (HP vs. cfm required).
Check air distribution system. Disassemble and inspect main air distribution valve, pilot valve and pilot valve actuators.
Discharge line is blocked or clogged manifolds. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Blocked air exhaust mufer. Remove mufer screen, clean or de-ice, and re-install.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump chamber is blocked. Disassemble and inspect wetted chambers. Remove or ush any obstructions.
Pump Cycles and Will
Not Prime or No Flow
Cavitation on suction side. Check suction condition (move pump closer to product).
Check valve obstructed. Valve ball(s) not seating
properly or sticking.
Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged.
Use heavier valve ball material.
Valve ball(s) missing (pushed into chamber or
manifold).
Worn valve ball or valve seat. Worn ngers in valve ball cage (replace part). Check Chemical
Resistance Guide for compatibility.
Valve ball(s)/seat(s) damaged or attacked by product. Check Chemical Resistance Guide for compatibility.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump Cycles Running
Sluggish/Stalling,
Flow Unsatisfactory
Over lubrication. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Icing. Remove mufer screen, de-ice, and re-install. Install a point of use air drier.
Clogged manifolds. Clean manifolds to allow proper air ow
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Cavitation on suction side. Check suction (move pump closer to product).
Lack of air (line size, PSI, CFM). Check the air line size, length, compressor capacity.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Air supply pressure or volume exceeds system hd. Decrease inlet air (press. and vol.) to the pump. Pump is cavitating the uid by fast cycling.
Undersized suction line. Meet or exceed pump connections.
Restrictive or undersized air line. Install a larger air line and connection.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. Purging the chambers of air can be dangerous.
Product Leaking
Through Exhaust
Diaphragm failure, or diaphragm plates loose. Replace diaphragms, check for damage and ensure diaphragm plates are tight.
Diaphragm stretched around center hole or bolt holes. Check for excessive inlet pressure or air pressure. Consult Chemical Resistance Chart for compatibility
with products, cleaners, temperature limitations and lubrication.
Premature Diaphragm
Failure
Cavitation. Enlarge pipe diameter on suction side of pump.
Excessive ooded suction pressure. Move pump closer to product. Raise pump/place pump on top of tank to reduce inlet pressure.
Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.
Misapplication (chemical/physical incompatibility). Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitations
and lubrication.
Incorrect diaphragm plates or plates on backwards,
installed incorrectly or worn.
Check Operating Manual to check for correct part and installation. Ensure outer plates have not been
worn to a sharp edge.
Unbalanced Cycling Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Undersized suction line. Meet or exceed pump connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs.
UNIVERSAL ALL AODD, EXCEPT FLAP
2: INSTAL & OP

spfp20sm-rev0516
7• Model SPFP20 Food Processing
www.standardpump.com
Composite Repair Parts Drawing - FDA Santoprene Fitted
2
34
5
6
7
8
9
10
11
11
1214
15
16
17
18
19
20
21
13 23
24
25
26
28
29
30
31
32
35
36
38
22
33
34
39
24
26
27
28
VERSA-DOME DIAPHRAGM ASSEMBLY
01 REV OE TO REV C MAV
REV REVISION CHG DATE APP DATE ECN
THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE
WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC.
DESCRIPTION
DRAWING NUMBER
WARREN RUPP INC.
REV
01
E2SJxxxx9C-FP-ATEX
E2 FOOD PRO HYTREL FITTED
PUMP
Torque to:
480 in-lbs
Torque to:
480 in-lbs
Torque to:
275 in-lbs
Torque to:
60 in-lbs
37
General Model Specic
3: EXP VIEW

spfp20sm-rev0516
Model SPFP20 Food Processing • 8
www.standardpump.com
Composite Repair Parts List - FDA Santoprene Fitted
Air Valve Assembly
Item # Qty. Description Part Number
Nickle Plated Stainless Steel
1 1 Valve Body (includes items 2-11) 200-201
200-206
2 1 Valve Body
3 1 Valve Body Gasket
4 1 Valve Sleeve
200-277
200-237
200-224
200-238
200-307
5 6 O-Ring
6 1 Valve Spool Assembly (Includes items 7)
7 6 Glyde Ring Assembly
8 1 Air Valve Screen 200-279
9 2 End Cap Gasket 200-278
200-332
200-324
10 2 End Cap
11 13 Mounting Screws
Center Section Assembly
Item # Qty. Description Part Number
Nickle Plated Stainess Steel
12 1 Center Block Assembly (Includes item 13) 200-281 200-440
13 2 Main Shaft O-Ring 200-282
14 2 Air Chamber 200-210
200-214
200-432
200-437
15 2 Air Chamber Gasket
16 8 Bolt 200-327
200-232
200-223
200-227
200-239
200-221
200-217
17 1 Pilot Sleeve Assembly (include item 18)
18 6 O-Ring
19 1 Retaining Ring
20 1 Pilot Spool Assembly (Includes item 21)
21 7 O-Ring
22 1 Mufer
Diaphragm Assembly / Elastomers
Item # Qty. Description
Part Number
Model SPFP20NPS Model SPFP20SSS
FDA Santoprene FDA Santoprene
23 1 Main Shaft 200-272
200-397
200-394
24 2 Diaphragm
25 2 O-Ring
26 2 Inner Diaphragm Plate 200-445
27 2 Bumper Washer N/A
200-381
200-398
200-400
28 2 Outer Diaphragm Plate
29 4 Valve Seat
30 4 Valve Ball
Wet End Assembly
Item # Qty. Description Part Number
31 2 Water Chamber 200-359
200-357
200-358
200-269
200-360
200-361
200-362
200-363
200-270
32 4 Large Clamp Half
33 4 Bolt
34 4 Wing Nut
35 1 Discharge Manifold
36 1 Suction Manifold
37 8 Small Clamp Half
38 8 Bolt
39 8 Wing Nut
Parts Not Shown For Rubber Mounting Feet
Qty. Description Part Number
4 Foot, Mounting 200-212
200-209
200-219
200-243
200-244
4Capscrew, Hex Head
4Nut, Hex
4 Lockwasher
8 Flatwasher
MODEL SPECIFIC
3: EXP VIEW
200-424
200-430
200-431
200-439

spfp20sm-rev0516
9• Model SPFP20 Food Processing
www.standardpump.com
2
34
5
6
7
8
9
10
11
11
1214
15
16
17
18
19
20
21
29
30
31
32
35
36
38
22
33
34
39
23
24
27
Torque to:
275 in-lbs
Torque to:
60 in-lbs
37
Composite Repair Parts Drawing - PTFE Fitted
40
26
24
28
2
34
5
6
7
8
9
10
11
11
1215
16
17
18
19
20
21
22
14
24
26
27
25
30
32
33
34
37
38
40
23
35
36
41
28
29
39
13
45
47
43
44
46
47
FUSION DIAPHRAGM ASSEMBLY
24
25
28
METAL SEAT ASSEMBLY
29
25
30
Y
Torque Setting:
275 in-lbs.
(31.1 N-m)
Torque Setting:
480 in-lbs.(54.2 N-m)
600 in-lbs (67.8 N-m)
For XL Material ONLY
Torque Setting:
60 in-lbs.
(6.78 N-m)
3: EXP VIEW

spfp20sm-rev0516
Model SPFP20 Food Processing • 10
www.standardpump.com
2
34
5
6
7
8
9
10
11
11
1214
15
16
17
18
19
20
21
29
30
31
32
35
36
38
22
33
34
39
23
24
27
Torque to:
275 in-lbs
Torque to:
60 in-lbs
37
Composite Repair Parts List - PTFE Fitted
Air Valve Assembly
Item # Qty. Description Part Number
Nickle Plated Stainless Steel
1 1 Valve Body (includes items 2-11) 200-201
200-206
200-428
200-431
2 1 Valve Body
3 1 Valve Body Gasket 200-277
200-237
200-224
200-238
200-307
4 1 Valve Sleeve
5 6 O-ring
6 1 Valve Spool Assembly (Includes items 7)
7 6 Glyde Ring Assembly
8 1 Air Valve Screen 200-279 200-439
9 2 End Cap Gasket 200-278
200-332
200-324
10 2 End Cap
11 13 Mounting Screws
Center Section Assembly
Item # Qty. Description Part Number
Nickle Plated Stainless Steel
12 1 Center Block Assembly (Includes item 13) 200-281 200-440
13 2 Main Shaft O-Ring 200-282
14 2 Air Chamber 200-210
200-214
200-432
200-437
15 2 Air Chamber Gasket
16 8 Bolt 200-327
200-232
200-223
200-227
200-239
200-221
200-217
17 1 Pilot Sleeve Assembly (include items 18 & 19)
18 6 O-ring
19 1 Retaining Ring
20 1 Pilot Spool Assembly (Includes item 21)
21 7 O-ring
22 1 Mufer
Diaphragm Assembly / Elastomers
Item # Qty. Description Part Number
Model SPFP20NPT Model SPFP20NPP Model SPFP20SST
MODEL SPFP20SSP
23 1 Main Shaft 200-273
200-396
N/A
200-436
200-456
200-457
200-273
200-396
N/A
200-436
200-456
200-457
24 2 Diaphragm
40 2 Back-Up Diaphragm
25 2 O-Ring 200-425
26 2 Inner Diaphragm Plate N/A 200-454 N/A 200-446
27 2 Bumper Washer 200-283
28 2 Outer Diaphragm Plate N/A 200-447 N/A 200-447
29 4 Valve Seat
30 4 Valve Ball
200-364 (See note 1)
200-399
Wet End Assembly
Item # Qty. Description Part Number
31 2 Water Chamber 200-359
200-357
200-358
200-269
200-360
200-361
200-362
200-363
200-270
200-230
32 4 Large Clamp Half
33 4 Bolt
34 4 Wing Nut
35 1 Discharge Manifold
36 1 Suction Manifold
37 8 Small Clamp Half
38 8 Bolt
39 8 Wing Nut
2 Diaphragm Seal Tape Kit (Not Pictured)
Parts Not Shown For Rubber Mounting Feet
Qty. Description Part Number
4 Foot, Mounting 200-212
200-209
200-219
200-243
200-244
4Capscrew, Hex Head
4Nut, Hex
4 Lockwasher
8 Flatwasher
Notes:
1.) In addition to this seat, (4) 200-425 o-rings are needed.
3: EXP VIEW

DATE: July 20, 2012
FECHA:
DATUM:
DATA:
DATO:
PÄIVÄYS:
AUTHORIZED/ APPROVED BY:
Approuve par:
Aprobado por:
Genehmigt von:
approvato da:
Goedgekeurd door:
Underskrift:
Valtuutettuna:
Bemyndiget av:
Autorizado Por:
10/13/2015 REV 08 VMQR 044FM
This product complies with the following European Community Directives:
Ce produit est conforme aux directives de la Communauté européenne suivantes:
Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses produkt erfüllt die folgenden Vorschriften der Europäischen Gemeinschaft:
Questo prodotto è conforme alle seguenti direttive CEE:
Dir produkt voldoet aan de volgende EG-richtlijnen:
Denna produkt överensstämmer med följande EU direktiv:
Standard Pump, Inc., erklærer herved som fabrikant, at ovennævnte produkt er i overensstemmelse med bestemmelserne i Direkktive:
Tämä tuote täyttää seuraavien EC Direktiivien vaatimukstet:
Dette produkt oppfyller kravene til følgende EC Direktiver:
Este produto está de acordo com as seguintes Directivas comunitárias:
MANUFACTURED BY:
FABRIQUE PAR:
FABRICADA POR:
HERGESTELLT VON:
FABBRICATO DA:
VERVAARDIGD DOOR:
TILLVERKAD AV:
FABRIKANT:
VALMISTAJA:
PRODUSENT:
FABRICANTE:
DECLARATION DE CONFORMITE • DECLARACION DE CONFORMIDAD • ERKLÄRUNG BEZÜGLICH EINHALTUNG DER VORSCHRIFTEN
DICHIARAZIONE DI CONFORMITÀ • CONFORMITEITSVERKLARING •DEKLARATION OM ÖVERENSSTÄMMELSE
EF-OVERENSSTEMMELSESERKLÆRING • VAATIMUSTENMUKAISUUSVAKUUTUS • SAMSVARSERKLÄRING
DECLARAÇAO DE CONFORMIDADE
STANDARD PUMP, INC.
®
1610 Satellite Blvd., Suite D
Duluth, GA 30097
USA
Tel: [phone]
This product has used the following harmonized standards to verify conformance:
Ce materiel est fabriqué selon les normes harmonisées suivantes, afin d’ en garantir la conformité:
Este producto cumple con las siquientes directrices de la comunidad europa:
Dieses produkt ist nach folgenden harmonisierten standards gefertigtworden, die übereinstimmung wird bestätigt:
Questo prodotto ha utilizzato i seguenti standards per verificare la conformita´:
De volgende geharmoniseerde normen werden gehanteerd om de conformiteit van dit produkt te garanderen:
För denna produkt har följande harmoniserande standarder använts för att bekräfta överensstämmelse:
Harmoniserede standarder, der er benyttet:
Tässä tuotteessa on sovellettu seuraavia yhdenmukaistettuja standardeja:
Dette produkt er produsert i overenstemmelse med fløgende harmoniserte standarder:
Este produto utilizou os seguintes padrões harmonizados para varificar conformidade:
PUMP MODEL SERIES: SPFP05, SPFP10, SPFP15, SPFP20, SPFP30,
SPSN15, SPSN20, SP3A15, SP3A20
Chris Murphy
Director of Operations
DECLARATION OF CONFORMITY
2006/42/EC
on Machinery, according
to Annex VIII
EN809:1998+
A1:2009

EC / EU DECLARATION OF CONFORMITY
The objective of the declaration described is in conformity with the relevant Union harmonisation legislation:
Directive 94/9/EC (until April 19, 2016) and Directive 2014/34/EU ( from April 20, 2016).
Date of Issue: 10 May 2014
Technical File No.: 203104000-1410/MER
Quality System Registration No: ISO 9001-2000
Conforming Apparatus: Air-Operated Metal
Double Diaphragm Pumps for Use In Potentially
Explosive Atmospheres
Hazardous Location Applied: II 2 G c T5
II 2 D c T100°C
 T5uidsupto95°C
Manufacturer: Standard Pump, Inc.
1610 Satellite Blvd., Suite D
Duluth, GA 30097
USA
OnFileWith: DEKRACerticationB.V.(0344)
Meander 1051
6825 MJ Arnhem
The Netherlands
Harmonized Standards Applied: BS EN 13463-1:2009 Non-Electrical Equipment
Potentially Explosive Atmospheres-Part 1 Basic
Methods and Requirements
EN 13463-5:2011 Non-Electrical Equipment for
Potentially Explosive Atmospheres-Part 5
Protection by Constructional Safety
Equipment: SPFP20, SPFP30, SPSN20, SPFP15, SPSN15
We hereby certify that the above apparatuses described above conforms with the protection
requirementsofCouncilDirective94/9/ECof23March1994AnnexVIIIontheapproximationof
the laws of the Member States Concerning Equipment and Protective Systems Intended for use
in Potentially Explosive Atmospheres
DATE/OFREVISION/TITLE: ChrisMurphy
24 March 2016 Director of Operations

Declaration of Conformity
Manufacturer:
Standard Pump, Inc.
1610 Satellite Blvd., Suite D, Duluth, GA 30097, USA
certifies that Air-Operated Double Diaphragm
Food Processing and Sanitary Pump Models comply with the European
Community Regulation 1935/2004/EC for Food Contact Materials.
Signature of authorized person
Revision Level: B
Printed name of authorized person
Chris Murphy Director of Operations
October 13, 2015
Date of issue
September 11, 2013
Title
Date of revision
SPFP05PPS
SPFP10PPS
SPFP15NPS
SPFP20NPS
SPFP20SSS
SPFP30NPT
SPFP30SST
SPFP30NPS
SPFP30SSS
SPFP05PPP
SPFP10PPP
SPFP15NPP
SPFP20NPP
SPFP20SSP
Food Processing Pump Models:
SPSN15NPS
SPSN20NPS
SPSN20SSS
SPSN15NPP
SPSN20NPP
SPSN20SSP
Sanitary Pump Models: