Standard Pump SPFP05 Parts list manual

1/2" Food Processing
SPFP05
.98
24.96
7.45
189.13
9.42
239.27
1.98
50.29
O.D.
TRI-CLAMP
SUCTION PORT
1.98
50.29
O.D.
TRI-CLAMP
DISCHARGE PORT
3/8"
AIR INLET
.25
6.35
2.38
60.45
5.07
128.75
8.19
208.13
6.03
153.26
10.41
264.41
.72
18.26
RUBBER FOOT
.72
18.26
RUBBER FOOT
4.49
113.92
8.20
208.33
3.15
80.07
4.34
110.24
5.67
144.08
1.19
30.16
RUBBER FOOT
3/8" NPT
AIR EXHAUST
Standard Pump
SPFP05 Models
• SPFP05PPT
• SPFP05PPS
• SPFP05PPP
STANDARD PUMP, INC®
1610 Satellite Blvd Suite D. Duluth, Ga. 30097 • Phone: [phone] • www.standardpump.com
1: PUMP SPECS2: INSTAL & OP3: EXP VIEW4: CERTIFICATES
Service & Operating Manual
Original Instructions

spfp05sm-rev0516
www.standardpump.com
IMPORTANT
Read the safety warnings and instructions in this manual
before pump installation and start-up. Failure to comply with
the recommendations stated in this manual could damage the
pump and void factory warranty.
When used for toxic or aggressive uids, the pump should
always be ushed clean prior to disassembly.
Airborne particles and loud noise hazards. Wear eye and ear
protection.
Before maintenance or repair, shut off the compressed air line,
bleed the pressure, and disconnect the air line from the pump.
Be certain that approved eye protection and protective clothing
are worn at all times. Failure to follow these recommendations
may result in serious injury or death.
When the pump is used for materials that tend to settle out
or solidify, the pump should be ushed after each use to
prevent damage. In freezing temperatures the pump should be
completely drained between uses.
Before pump operation, inspect all fasteners for loosening
caused by gasket creep. Retighten loose fasteners to prevent
leakage. Follow recommended torques stated in this manual.
CAUTION
WARNING
Nonmetallic pumps and plastic components are not UV
stabilized. Ultraviolet radiation can damage these parts and
negatively affect material properties. Do not expose to UV light
for extended periods of time.
In the event of diaphragm rupture, pumped material may enter
the air end of the pump, and be discharged into the atmosphere.
If pumping a product that is hazardous or toxic, the air exhaust
must be piped to an appropriate area for safe containment.
This pump is pressurized internally with air pressure during
operation. Make certain that all fasteners are in good condition
and are reinstalled properly during reassembly.
Take action to prevent static sparking. Fire or explosion can
result, especially when handling ammable liquids. The pump,
piping, valves, containers and other miscellaneous equipment
must be properly grounded.
Safety Information
UNIVERSAL ALL AODD
WARNING
Pump not designed, tested or certied to be powered by
compressed natural gas. Powering the pump with natural
gas will void the warranty.
Use safe practices when lifting
kg

spfp05sm-rev0516 www.standardpump.com
Table of Contents
SECTION 1: PUMP SPECIFICATIONS................1
• Performance
• Materials
• Dimensional Drawings
SECTION 2: INSTALLATION & OPERATION......4
• Principle of Pump Operation
• Typical Installation Guide
• Troubleshooting
SECTION 3: EXPLODED VIEW...........................7
• Composite Drawings
• Parts List
• Materials Code
SECTION 4: CERTIFICATES ..............................9
• EC Declaration of Conformity - Directive 2006/42/EC - Machinery
• EC Declaration of Conformity - Directive 1935/2004/EC - Food Contact Materials
Universal*
1: PUMP SPECS2: INSTAL & OP3: EXP VIEW4: CERTIFICATES

spfp05sm-rev0516
1• Model SPFP05 Food Processing
www.standardpump.com
Performance
Meters Feet
Discharge Head in PSI
2 106
0
100
90
80
70
60
50
40
30
20
10
0
240
220
200
180
160
140
120
100
80
60
40
20
0
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
1284
40
0
5 10 15 20 25 30 35 45 50
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.022 Gal. (0.08 L)
4
8
12
2
AIR CONSUMPTION IN SCFM
AIR PRESSURE IN PSI
SCFM M3/HR
2 3.4
4 6.8
8 13.6
12 20.4
0
1
2
3
4
5
6
7
BAR
Discharge Head in PSI
2 106
0
100
90
80
70
60
50
40
30
20
10
0
Meters Feet
240
220
200
180
160
140
120
100
80
60
40
20
0
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0 0
1
2
3
4
5
6
7
BAR 1284
40
0
5 10 15 20 25 30 35 45 50
Capacity in Liters Per Minute
Capacity in U.S. Gallons Per Minute
Displacement Per Stroke, 0.019 Gal. (0.08 L)
4
8
12
2
AIR CONSUMPTION IN SCFM
AIR PRESSURE IN PSI
SCFM M3/HR
2 3.4
4 6.8
8 13.6
12 20.4
Model SPFP05PPS 1/2" Bolted Metal
FDA SANTOPRENE FITTED
Flow Rate
Adjustable to ..........0-12 gpm (45.4 lpm)
Port Size
Suction ...................1 ½" Tri-Clamp
Discharge.................1 ½" Tri-Clamp
Air Inlet ........................3/8" NPT
Air Exhaust ....................3/8" NPT
Suction Lift
Dry ......................... 13' (3.9 m)
Wet......................... 22' (6.7 m)
Max Solid Size (Diameter)
.........................1/16" (1.6 mm)
Max Noise Level ...............84 dB(A)
Shipping Weights
Stainless...................17 lbs (7.7 kg)
Model SPFP05PPT 1/2" Bolted Metal
PTFE FITTED
Flow Rate
Adjustable to ..........0-11 gpm (41.6 lpm)
Port Size
Suction ...................1 ½" Tri-Clamp
Discharge.................1 ½" Tri-Clamp
Air Inlet ........................3/8" NPT
Air Exhaust ....................3/8" NPT
Suction Lift
Dry ......................... 12' (3.6 m)
Wet......................... 22' (6.7 m)
Max Solid Size (Diameter)
.........................1/16" (1.6 mm)
Max Noise Level ...............87 dB(A)
Shipping Weights
Stainless...................17 lbs (7.7 kg)
NOTE: Performance based on the following: PTFE tted pump, ooded suction, water at ambient
conditions. The use of other materials and varying hydraulic conditions may result in deviations in
excess of 5%.
NOTE: Performance based on the following: PTFE tted pump, ooded suction, water at ambient
conditions. The use of other materials and varying hydraulic conditions may result in deviations in
excess of 5%.
1: PUMP SPECS

spfp05sm-rev0516
Model SPFP05 Food Processing • 2
www.standardpump.com
Materials
Material Prole: Operating
Temperatures:
Max. Min.
Polypropylene: A thermoplastic polymer. Moderate tensile
and ex strength. Resists stong acids and alkali. Attacked by
chlorine, fuming nitric acid and other strong oxidizing agents.
180°F
82°C
32°F
0°C
Santoprene®: Injection molded thermoplastic elastomer with
no fabric layer. Long mechanical ex life. Excellent abrasion
resistance.
275°F
135°C
-40°F
-40°C
Virgin PTFE: (PFA/TFE) Chemically inert, virtually impervious.
Very few chemicals are known to chemically react with PTFE;
molten alkali metals, turbulent liquid or gaseous uorine and
a few uoro-chemicals such as chlorine triuoride or oxygen
diuoride which readily liberate free uorine at elevated
temperatures.
220°F
104°C
-35°F
-37°C
Maximum and Minimum Temperatures are the limits for which these materials can be operated.
Temperatures coupled with pressure affect the longevity of diaphragm pump components.
Maximum life should not be expected at the extreme limits of the temperature ranges.
Metals:
Stainless Steel: Equal to or exceeding ASTM specication A743 CF-8M for corrosion
resistant iron chromium, iron chromium nickel and nickel based alloy castings for
general applicaitons. Commonly referred to as 316 Stainless Steel in the pump industry.
CAUTION! Operating temperature limitations are as follows:
Ambient temperature range -20 C to +40 C
Process temperature range -20 C to +80 C for models rated as category 1 equipment
-20 c to +100 C for model rated as category 2 equipment
In addition, the ambient temperature range and the process temperature range do not
exceed the operating temperature range of the applied non-metallic parts as listed in the
manuals of the pumps.
Note: This document is a high level guide. Please be aware that not all model and or material
combinations are possible for all sizes. Please consult factory or your distributor for specic details.
MODEL SPECIFIC UNIVERSAL ALL AODD
1: PUMP SPECS

spfp05sm-rev0516
3• Model SPFP05 Food Processing
www.standardpump.com
Model SPFP05 Metallic Bolted
Dimensions in inches (mm dimensions in brackets).
The dimensions on this drawing are for reference only. A certied drawing can be requested if physical dimensions are needed.
Dimensional Drawings
.98
24.96
7.45
189.13
9.42
239.27
1.98
50.29
O.D.
TRI-CLAMP
SUCTION PORT
1.98
50.29
O.D.
TRI-CLAMP
DISCHARGE PORT
3/8"
AIR INLET
.25
6.35
2.38
60.45
5.07
128.75
8.19
208.13
6.03
153.26
10.41
264.41
.72
18.26
RUBBER FOOT
.72
18.26
RUBBER FOOT
4.49
113.92
8.20
208.33
3.15
80.07
4.34
110.24
5.67
144.08
1.19
30.16
RUBBER FOOT
3/8" NPT
AIR EXHAUST
Model Specic
1: PUMP SPECS

spfp05sm-rev0516
Model SPFP05 Food Processing • 4
www.standardpump.com
Air Line
Discharged
Fluid
Discharge
Stroke Suction
Stroke
Primed
Fluid
Air-Operated Double Diaphragm (AODD) pumps are powered
by compressed air or nitrogen.
The main directional (air) control valve ①distributes
compressed air to an air chamber, exerting uniform pressure
over the inner surface of the diaphragm
②. At the same time,
the exhausting air ③ from behind the opposite diaphragm
is directed through the air valve assembly(s) to an exhaust
port ④.
As inner chamber pressure (P1) exceeds liquid chamber
pressure (P2), the rod ⑤connected diaphragms shift
together creating discharge on one side and suction on the
opposite side. The discharged and primed liquid’s directions
are controlled by the check valves (ball or ap)⑥orientation.
The pump primes as a result of the suction stroke. The
suction stroke lowers the chamber pressure (P3) increasing
the chamber volume. This results in a pressure differential
necessary for atmospheric pressure (P4) to push the uid
through the suction piping and across the suction side check
valve and into the outer uid chamber ⑦.
Suction (side) stroking also initiates the reciprocating
(shifting, stroking or cycling) action of the pump. The suction
diaphragm’s movement is mechanically pulled through its
stroke. The diaphragm’s inner plate makes contact with an
actuator plunger aligned to shift the pilot signaling valve.
Once actuated, the pilot valve sends a pressure signal to the
opposite end of the main directional air valve, redirecting the
compressed air to the opposite inner chamber.
Principle of Pump Operation
SAFE AIR
EXHAUST
DISPOSAL
AREA
PUMP INSTALLATION AREA
1" DIAMETER AIR
EXHAUST PIPING
1" DIAMETER AIR
EXHAUST PIPING
1" DIAMETER AIR
EXHAUST PIPING
MUFFLER
LIQUID
LEVEL
SUCTION
LINE
LIQUID
LEVEL
SUCTION
LINE
MUFFLER
MUFFLER
SUBMERGED ILLUSTRATION
Pump can be submerged if the pump materials of construction
are compatible with the liquid being pumped. The air exhaust
must be piped above the liquid level. When the pumped product
source is at a higher level than the pump (ooded suction
condition), pipe the exhaust higher than the product source to
prevent siphoning spills.
MODEL SPECIFIC
2: INSTAL & OP

spfp05sm-rev0516
5• Model SPFP05 Food Processing
www.standardpump.com
Installation And Start-Up
Locate the pump as close to the product being pumped as possible. Keep the suction line length and number of ttings to a minimum. Do not reduce the suction line
diameter.
Air Supply
Connect the pump air inlet to an air supply with sufcient capacity and pressure to achieve desired performance. A pressure regulating valve should be installed to
insure air supply pressure does not exceed recommended limits.
Air Valve Lubrication
The air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricator
set to deliver one drop of SAE 10 non-detergent oil for every 20 SCFM (9.4 liters/sec.) of air the pump consumes. Consult the Performance Curve to determine air
consumption.
Air Line Moisture
Water in the compressed air supply may cause icing or freezing of the exhaust air, causing the pump to cycle erratically or stop operating. Water in the air supply can
be reduced by using a point-of-use air dryer.
Air Inlet And Priming
To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air ow as desired. If opening the valve
increases cycling rate, but does not increase the rate of ow, cavitation has occurred. The valve should be closed slightly to obtain the most efcient air ow to pump
ow ratio.
Surge Suppressor
Shut-Off Valve
Pressure Gauge
Drain Port
Shut-Off
Valve
Check
Valve
Air Inlet
Discharge
Unregulated Air
Supply to Surge
Suppressor
Pipe Connection
(Style Optional)
Flexible Connector
Flexible Connector
Vacuum
Gauge
Suction
Shut-Off Valve
Drain Port Pipe Connection
(Style Optional)
Flexible
Connector
Air Dryer
Filter Regulator
P/N: 020.V107.000
Note: Pipe weight should not be supported
by pump connections.
Muffler
(Optional Piped Exhaust)
Recommended Installation Guide
Available Accessories:
1. Surge Suppressor
2. Filter/Regulator
3. Air Dryer
1
2
3
Note: Surge Suppressor and
Piping must be supported after
the exible connection.
CAUTION
The air exhaust should
be piped to an area
for safe disposition
of the product being
pumped, in the event of
a diaphragm failure.
UNIVERSAL ALL AODD
2: INSTAL & OP

spfp05sm-rev0516
Model SPFP05 Food Processing • 6
www.standardpump.com
Recommended Installation Guide Troubleshooting Guide
Symptom: Potential Cause(s): Recommendation(s):
Pump Cycles Once Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Air valve or intermediate gaskets installed incorrectly. Install gaskets with holes properly aligned.
Bent or missing actuator plunger. Remove pilot valve and inspect actuator plungers.
Pump Will Not Operate
/ Cycle
Pump is over lubricated. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Lack of air (line size, PSI, CFM). Check the air line size and length, compressor capacity (HP vs. cfm required).
Check air distribution system. Disassemble and inspect main air distribution valve, pilot valve and pilot valve actuators.
Discharge line is blocked or clogged manifolds. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Blocked air exhaust mufer. Remove mufer screen, clean or de-ice, and re-install.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump chamber is blocked. Disassemble and inspect wetted chambers. Remove or ush any obstructions.
Pump Cycles and Will
Not Prime or No Flow
Cavitation on suction side. Check suction condition (move pump closer to product).
Check valve obstructed. Valve ball(s) not seating
properly or sticking.
Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged.
Use heavier valve ball material.
Valve ball(s) missing (pushed into chamber or
manifold).
Worn valve ball or valve seat. Worn ngers in valve ball cage (replace part). Check Chemical
Resistance Guide for compatibility.
Valve ball(s)/seat(s) damaged or attacked by product. Check Chemical Resistance Guide for compatibility.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump Cycles Running
Sluggish/Stalling,
Flow Unsatisfactory
Over lubrication. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Icing. Remove mufer screen, de-ice, and re-install. Install a point of use air drier.
Clogged manifolds. Clean manifolds to allow proper air ow
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Cavitation on suction side. Check suction (move pump closer to product).
Lack of air (line size, PSI, CFM). Check the air line size, length, compressor capacity.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Air supply pressure or volume exceeds system hd. Decrease inlet air (press. and vol.) to the pump. Pump is cavitating the uid by fast cycling.
Undersized suction line. Meet or exceed pump connections.
Restrictive or undersized air line. Install a larger air line and connection.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. Purging the chambers of air can be dangerous.
Product Leaking
Through Exhaust
Diaphragm failure, or diaphragm plates loose. Replace diaphragms, check for damage and ensure diaphragm plates are tight.
Diaphragm stretched around center hole or bolt holes. Check for excessive inlet pressure or air pressure. Consult Chemical Resistance Chart for compatibility
with products, cleaners, temperature limitations and lubrication.
Premature Diaphragm
Failure
Cavitation. Enlarge pipe diameter on suction side of pump.
Excessive ooded suction pressure. Move pump closer to product. Raise pump/place pump on top of tank to reduce inlet pressure.
Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.
Misapplication (chemical/physical incompatibility). Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitations
and lubrication.
Incorrect diaphragm plates or plates on backwards,
installed incorrectly or worn.
Check Operating Manual to check for correct part and installation. Ensure outer plates have not been
worn to a sharp edge.
Unbalanced Cycling Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Undersized suction line. Meet or exceed pump connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs.
UNIVERSAL ALL AODD, EXCEPT FLAP
2: INSTAL & OP

spfp05sm-rev0516
7• Model SPFP05 Food Processing
www.standardpump.com
Composite Repair Parts Drawing
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
34
35
35
36
36
37
22
21
FUSION DIAPHRAGM ASSEMBLY
22
23
21
24
25
PTFE 2-PIECE DIAPHRAGM ASSEMBLY
Torque Setting:
60 in-lbs.
Torque Setting:
70 in-lbs.
Torque Setting:
60 in-lbs.
Torque Setting:
90 in-lbs.
Torque Setting:
90 in-lbs.
Torque Setting:
30 in-lbs.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
34
35
35
36
36
37
22
21
FUSION DIAPHRAGM ASSEMBLY
22
23
21
24
25
PTFE 2-PIECE DIAPHRAGM ASSEMBLY
Torque Setting:
60 in-lbs.
Torque Setting:
70 in-lbs.
Torque Setting:
60 in-lbs.
Torque Setting:
90 in-lbs.
Torque Setting:
90 in-lbs.
Torque Setting:
30 in-lbs.
General Model Specic
3: EXP VIEW

spfp05sm-rev0516
Model SPFP05 Food Processing • 8
www.standardpump.com
Composite Repair Parts List
Air Valve Assembly
Item # Qty. Description Part Number
- 1 Valve Body (includes items 1-11) 200-204
200-323
200-256
200-321
200-322
200-423
200-259
200-208
200-260
200-216
200-325
1 1 Valve Body
2 1 Valve Spool Assembly (Includes items 3&4)
3 1 Large Valve Spool U-Cup
4 1 Small Valve Spool U-Cup
5 1 End Cap Assembly (Includes O-Ring)
6 1 Reducing End Cap Assembly (Includes 560.0580.360 O-Rings)
7 2 Staple
8 1 CT Air Diverter
9 1 Air Diverter Plate
10 1 Air Valve Gasket
11 4 Valve Mounting Screws
Center Section Assembly
Item # Qty. Description Part Number
12 1 Center Section 200-261
200-240
200-221
200-233
200-222
200-225
200-262
200-420
13 1 Pilot Spool ASY (Includes Item #14)
14 8 Pilot Spool O-Rings
15 1 Pilot Valve Sleeve ASY (Includes Item #16)
16 6 Pilot Valve Sleeve O-Rings
17 2 Shaft/Pilot Retainer
18 4 Retainer Screw
19 1 Mufer
Diaphragm Assembly / Elastomers
Item # Qty. Description
Part Number
SPFP05PPS SPFP05PPP SPFP05PPT
FDA Santoprene PTFE 2-Piece PTFE Fusion
20 2 Main Shaft O-Ring 200-264
200-263
200-435
200-434
21 1 Main Shaft
22 2 Diaphragm 200-267 200-266
23 2 Back-Up Diaphragm N/A N/A
24 2 Inner Diaphragm Plate 200-393
200-356
N/A
25 2 Outer Diaphragm Plate N/A
26 4 Valve Seat O-Ring 200-382
200-383
27 4 Valve Ball
Wet End Assembly
Item # Qty. Description Part Number
28 2 Water Chamber 200-265
200-348
200-347
200-343
200-333
200-353
200-354
200-352
200-355
29 16 Water Chamber Bolt
30 16 Water Chamber Washer
31 16 Water Chamber Nut
32 4 Valve Seat
33 1 Discharge Manifold
34 1 Suction Manifold
35 8 Manifold Bolts
36 8 Manifold Washer
37 8 Manifold Nut
Parts Not Shown (For Rubber Mounting Feet)
Qty. Description Part Number
4 Foot, Mounting 200-213
200-220
200-229
200-245
4Nut, Hex
4 Machine Screw
4 Flat Washer
MODEL SPECIFIC
3: EXP VIEW
200-258
200-351

DATE: July 20, 2012
FECHA:
DATUM:
DATA:
DATO:
PÄIVÄYS:
AUTHORIZED/ APPROVED BY:
Approuve par:
Aprobado por:
Genehmigt von:
approvato da:
Goedgekeurd door:
Underskrift:
Valtuutettuna:
Bemyndiget av:
Autorizado Por:
10/13/2015 REV 08 VMQR 044FM
This product complies with the following European Community Directives:
Ce produit est conforme aux directives de la Communauté européenne suivantes:
Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses produkt erfüllt die folgenden Vorschriften der Europäischen Gemeinschaft:
Questo prodotto è conforme alle seguenti direttive CEE:
Dir produkt voldoet aan de volgende EG-richtlijnen:
Denna produkt överensstämmer med följande EU direktiv:
Standard Pump, Inc., erklærer herved som fabrikant, at ovennævnte produkt er i overensstemmelse med bestemmelserne i Direkktive:
Tämä tuote täyttää seuraavien EC Direktiivien vaatimukstet:
Dette produkt oppfyller kravene til følgende EC Direktiver:
Este produto está de acordo com as seguintes Directivas comunitárias:
MANUFACTURED BY:
FABRIQUE PAR:
FABRICADA POR:
HERGESTELLT VON:
FABBRICATO DA:
VERVAARDIGD DOOR:
TILLVERKAD AV:
FABRIKANT:
VALMISTAJA:
PRODUSENT:
FABRICANTE:
DECLARATION DE CONFORMITE • DECLARACION DE CONFORMIDAD • ERKLÄRUNG BEZÜGLICH EINHALTUNG DER VORSCHRIFTEN
DICHIARAZIONE DI CONFORMITÀ • CONFORMITEITSVERKLARING •DEKLARATION OM ÖVERENSSTÄMMELSE
EF-OVERENSSTEMMELSESERKLÆRING • VAATIMUSTENMUKAISUUSVAKUUTUS • SAMSVARSERKLÄRING
DECLARAÇAO DE CONFORMIDADE
STANDARD PUMP, INC.
®
1610 Satellite Blvd., Suite D
Duluth, GA 30097
USA
Tel: [phone]
This product has used the following harmonized standards to verify conformance:
Ce materiel est fabriqué selon les normes harmonisées suivantes, afin d’ en garantir la conformité:
Este producto cumple con las siquientes directrices de la comunidad europa:
Dieses produkt ist nach folgenden harmonisierten standards gefertigtworden, die übereinstimmung wird bestätigt:
Questo prodotto ha utilizzato i seguenti standards per verificare la conformita´:
De volgende geharmoniseerde normen werden gehanteerd om de conformiteit van dit produkt te garanderen:
För denna produkt har följande harmoniserande standarder använts för att bekräfta överensstämmelse:
Harmoniserede standarder, der er benyttet:
Tässä tuotteessa on sovellettu seuraavia yhdenmukaistettuja standardeja:
Dette produkt er produsert i overenstemmelse med fløgende harmoniserte standarder:
Este produto utilizou os seguintes padrões harmonizados para varificar conformidade:
PUMP MODEL SERIES: SPFP05, SPFP10, SPFP15, SPFP20, SPFP30,
SPSN15, SPSN20, SP3A15, SP3A20
Chris Murphy
Director of Operations
DECLARATION OF CONFORMITY
2006/42/EC
on Machinery, according
to Annex VIII
EN809:1998+
A1:2009

Declaration of Conformity
Manufacturer:
Standard Pump, Inc.
1610 Satellite Blvd., Suite D, Duluth, GA 30097, USA
certifies that Air-Operated Double Diaphragm
Food Processing and Sanitary Pump Models comply with the European
Community Regulation 1935/2004/EC for Food Contact Materials.
Signature of authorized person
Revision Level: B
Printed name of authorized person
Chris Murphy Director of Operations
October 13, 2015
Date of issue
September 11, 2013
Title
Date of revision
SPFP05PPS
SPFP10PPS
SPFP15NPS
SPFP20NPS
SPFP20SSS
SPFP30NPT
SPFP30SST
SPFP30NPS
SPFP30SSS
SPFP05PPP
SPFP10PPP
SPFP15NPP
SPFP20NPP
SPFP20SSP
Food Processing Pump Models:
SPSN15NPS
SPSN20NPS
SPSN20SSS
SPSN15NPP
SPSN20NPP
SPSN20SSP
Sanitary Pump Models: