Stanley P1450B User manual

Contents:
Page 2 Factory Original Parts
Page 3 Package Contents/Component Identification
Page 5 Warnings
Page 7 Preparation & Assembly - Model 1450B, 1450B-CAN,
P1500B, P1600B, P1600B-BB, P1600B-CAN, P1760B-BB,
Page 8 Preparation & Assembly - Model 1750B, 1750B-CAN
P1800B, P1800B-BB, P1800B-CAN, P2000B-BB
Page 9 Operation
Page 13 Maintenance
Page 14 Tips for Cleaning
Page 14 Troubleshooting
Page 16 Spare Parts List
Page 17 Warranty
Page 18 Extended Warranty & Product Registration Card
DO NOT RETURN UNIT TO THE STORE!
QUESTIONS OR NEED HELP?
Call: 919-550-3221
www.GXiOutdoorPower.com
Have the following information ready when you call us:
Date of Purchase: _____________________________
Location of Purchase: __________________________
Serial #: ____________________________________
Is a registered trademark of The Beast Works or its affiliates and is
used under license by GXi Outdoor Power, LLC.
IMPORTANT SAFETY INSTRUCTIONS:
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS
Electric Pressure Washer Owner’s Manual
This Manual Contains Important Safety Instructions and Operating Instructions
Models: P1450B, P1750B, P1450B-CAN, P1500B, P1750B-CAN, P1600B, P1800B
P1600B-BB, P1760B-BB, P1800B-BB, P1600B-CAN, P1800B-CAN, P2000B-BB
TO PREVENT PREMATURE WEAR ON PRESSURE
WASHER PUMP, DO NOT ALLOW UNIT TO RUN
MORE THAN 30 MINUTES AT A TIME

ORDER ONLINE NOW AND SAVE!
www.GXiOutdoorPower.com
Phone orders, call [1] 919-550-3221
Please have the part number and credit card ready when calling.
Replacement Gun
Part Number: SP01009
Price: $30.00
Replacement Adjustable Wand
Part Number: SP00209 (Model P1450B, 1450B-CAN,P1500B,
P1600B, P1600B-BB, P1600B-CAN,P1760B-BB)
Part Number: SP00309 (Model P1750B, 1750B-CAN,
P1800B, P1800B-BB, P1800B-CAN, P2000B-BB)
Replacement Turbo Wand
Part Number: SP00409
Price: $30.00
Replacement High Pressure Hose
Part Number: SP00509 (Model P1450B, P1450B-CAN, P1500B,
P1600B, P1600B-BB, P1600B-CAN, P1760B-BB)
Part Number: SP02412 (Model P1750B, P1750B-CAN, P1800B,
P1800B-BB, P1800B-CAN, P2000B-BB)
Replacement Rotary and Straight Brush
Part Number: SP00709 (Rotary Brush)
Part Number: SP00809 (Straight Brush)
For replacement parts not listed here,
see pages 3-4.
Rotary Brush Straight Brush
FACTORY ORIGINAL BEAST PARTS
Price: $30.00
Price: $30.00
Price: $30.00 Each
SP00509 SP02412

3 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
PACKAGE CONTENTS (P1450B, P1450B-CAN, P1500B, P1600B, P1600B-BB, P1600B-CAN, P1760B-BB)
A
* Standard quantity where applicable, not all products come standard with all features
and/or accessories. See chart for standard features by model.
Note:
Not all accessories are
included with every model.
Some accessories may be sold
separately
A: Main Unit 1
B: Spray Gun 1
C: High Pressure Adjustable Wand 1
D: Turbo Wand 1
E: Straight Brush 1
F: Rotary Brush 1
G: Soap Injector 1
H: Gun Holder 1
I: Zinc Connect 1
** One filter comes in the machine water inlet, an extra is provided in the hardware bag.
Note:
Not all accessories are
included with every model.
Some accessories may be sold
separately
J: Plastic Quick Connect (2 pcs.) 1
K: Brass Quick Connect (2 pcs.) 1
L: 17mm Wrench 1
M: Cleaning Needle 1
N: Water Filter 2**
O: O-Ring 6
P: Hose Strap 1
Q: High Pressure Hose 1
R: Tool Belt 1
P1450B P1450B-CAN P1600B-BB, P1760B-BB
P1600B-CAN P1600B Qty.*
P1500B
P1450B P1450B-CAN P1600B-BB, P1760B-BB P1600B-CAN P1600B Qty.*
P1500B

Rev: Jan 2018
4 of 18
®
BEAST Electric Pressure Washers
PACKAGE CONTENTS (P1750B, P1750B-CAN, P1800B, P1800B-BB, P1800B-CAN P2000B-BB)
** One filter comes in the machine water inlet, an extra is provided in the hardware bag.
Note:
Not all accessories are
included with every model.
Some accessories may be sold
separately
K: Brass Quick Connect (2 pcs.) 1
L: 17mm Wrench 1
M: Cleaning Needle 1
N: Water Filter 2**
O: O-Ring 6
P: High Pressure Hose 1
Q: Hose Reel 1
R: Soap Bottle Holder 1
S: Soap Bottle 1
T: Detachable Foot 1
P1750B P1750B-CAN P1800B-BB P1800B-CAN P1800B Qty.* P2000B-BB
* Standard quantity where applicable, not all products come standard with all features
and/or accessories. See chart for standard features by model.
Note:
Not all accessories are
included with every model.
Some accessories may be sold
separately
A: Main Unit 1
B: Spray Gun 1
C: Adjustable Wand 1
D: Turbo Wand 1
E: Straight Brush 1
F: Rotary Brush 1
G: Extension Hose 1
H: Gun Holder 1
I: Zinc Connect 1
J: Plastic Quick Connect (2 pcs.) 1
P1750B P1750B-CAN P1800B-BB P1800B-CAN P1800B Qty.* P2000B-BB

5 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
This owner’s manual is considered a permanent part of the pressure
washer and should remain with the pressure washer if resold. The
information and specifications included in this publication were in
effect at the time of approval for printing.
GXi Outdoor Power, LLC reserves the right to discontinue or change
specifications or design at any time without notice and without
incurring any obligation whatever. No part of this publication may be
reproduced without written permission.
SAFETY LABEL LOCATIONS
These labels warn you of potential hazards that can cause serious
injury. Read them carefully. If a label comes off or becomes hard to
read, contact Customer Care for a replacement.
SAFETY INFORMATION
BEAST pressure washers are designed to give safe and dependable
service if operated according to instructions. Read and understand this
owner’s manual before operating your pressure washer.
OPERATOR RESPONSIBILITY
Know how to stop the pressure washer quickly in case of emergency.
Understand the use of all product controls, output receptacles, and
connections. Be sure that anyone who operates the pressure washer
receives proper instruction. Do not let children operate the pressure
washer.
WARNINGS
WARNING
Use of pressure washer can create puddles and slippery
surfaces.
 The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.
High pressure spray could cause you to fall if you are too close
to the cleaning surface.
 Keep spray nozzle between 8 to 24 inches away from cleaning
surface.
 Operate this unit on a stable surface.
 Be extremely careful if you must use the pressure washer from a
ladder, scaffolding or any other relatively unstable location. Firmly
grasp spray gun with both hands when using high pressure spray to
avoid injury if gun kicks back.
Some chemicals or detergents may be harmful if inhaled or
ingested, causing severe nausea, fainting or poisoning.
 Use a respirator or mask whenever there is a chance that vapors
may be inhaled.
 Read all instructions with mask so you are certain the mask will
provide the necessary protection against inhaling harmful vapors.
 Do not use acids and solvents in this product. These products can
cause physical injuries to the operator and irreversible damage to
the machine.
 Do not use with toxic chemicals.
 To minimize the amount of water getting into the pressure washer,
the unit should be placed as far as possible from the cleaning site
during operation.
 Never carry your pressure washer by the cord. Do not pull on the
cord to disconnect from the outlet.
 To allow free air circulation, the pressure washer should not be
covered during operation.
 California Proposition 65: This product or its power cord contains
lead, a chemical known to the State of California to cause cancer,
birth defects or other reproductive harm. Wash hands after use.
WARNING
SAFETY FEATURES AND ELECTRICAL POWER
INFORMATION
The pressure washer is equipped with a stop device that will sense
when the trigger on the gun is released. It will open the power circuit to
the motor and cause the pressure washer motor to stop. Motor will
resume again when trigger is pulled.
WARNING
The pressure washer is also equipped with a main power “ON/
OFF” switch located on the unit. It should always be moved to
the “OFF” position when the pressure washer is not being used
to prevent possible injury or damage.
Ground Fault Circuit Interrupter:
This pressure washer has a ground-fault circuit-interrupter (GFCI) built
into the plug of the power supply cord. This device provides additional
protection from the risk of shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that include
GFCI protection.
Extension cords are not recommended unless they are plugged
into a ground fault circuit-interrupter found in circuit boxes or
protected receptacles.
SAVE THESE INSTRUCTIONS
Servicing of a double-insulation product:
In a double-insulated product two systems of insulation are provided
instead of grounding. No grounding means is provided on a double
insulated product, nor should a means for grounding be added to the
product. Servicing a double-insulated product requires extreme care
and knowledge of the system, and should be done only by qualified
service personnel. Replacement parts of a double-insulated product
must be identical to the parts they replace. A double-insulated product
is marked with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED”.
The symbol may also be marked on the product.
WHEN OPERATING EQUIPMENT
 Avoid accidental starts. Shut power “OFF” before connecting or
disconnecting cord to electrical outlets.
 DO NOT spray flammable liquids.

Rev: Jan 2018
6 of 18
®
BEAST Electric Pressure Washers
The high pressure stream of water that this equipment produces
can pierce skin and its underlying tissues, leading to serious
injury and possible amputation.
Spray gun traps high water pressure, even when pump is not
running and water is disconnected, which can cause injury.
 NEVER aim spray gun at people, animals, plants, electrical devices,
or the unit itself.
 DO NOT allow children to operate pressure washer.
 To reduce the risk of injury, do not operate the machine near
children
 NEVER repair high pressure hose. Replace it.
 NEVER repair leaking connections with sealant of any kind.
Replace o-ring or seal.
 Keep high pressure hose connected to pump and spray gun while
system is pressurized.
 ALWAYS point gun in safe direction and squeeze spray gun trigger,
to release high pressure, every time you stop engine. Engage
trigger lock when not in use.
WARNING
High pressure spray can cause paint chips or other particles to
become airborne.
 Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.
WARNING
Risk of Electrocution
 Inspect cord before using - Do not use if cord is damaged.
 Keep all connections dry and off the ground.
 Do not touch plug with wet hands.
 If possible, do not use extension cords with the product.
 Water spray must never be directed towards any electric wiring,
electrical devices, or toward the unit itself.
WARNINGS
Extension Cords
If possible, do not use extension cords with this
product. However, if you must use one, observe all
the warnings and instructions listed below: Use a sufficient gauge:
 Maximum cable length: 50 ft = 14 AWG
 Use only extension cords that are intended for outdoor use. These
extension cords are identified by a marking “Acceptable for use
with outdoor appliances; store indoors while not in use.”
 Use only extension cords having an electrical rating not less than
the rating of the product.
 Do not use damaged extension cords. Examine extension cord
before using and replace if damaged.
 Do not abuse extension cord and do not yank on any cord to
disconnect.
 Keep cord away from heat and sharp edges.
 Always disconnect the extension cord from the receptacle before
disconnecting the product from the extension cord.
 To reduce the risk of electrocution, keep all connections dry and off
the ground. Do not touch plug with wet hands.
WARNING
The pressure washer is also equipped with a main power “ON/OFF”
switch located on the unit. It should always be moved to the “OFF”
position when the pressure washer is not being used to prevent possible
injury or damage.
CAUTION
A pressure washer produces a high pressure spray which
increases risk of injury and damage to unit.
 Gun Kicks Back - Hold with both hands!
 The trigger gun safety lock prevents the trigger from accidentally
being engaged. The safety feature DOES NOT lock trigger in the ON
position.
 DO NOT secure spray gun in open position.
 DO NOT leave spray gun unattended while machine is running.
 NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.
 Always be certain spray gun, nozzles and accessories are correctly
attached.
High pressure spray may damage fragile items including glass.
 DO NOT point spray gun at glass when in jet spray mode.
 NEVER aim spray gun at people, animals, plants, electrical devices,
or the unit itself.
CAUTION
Risk of Explosion
 DO NOT spray flammable liquids
 DO NOT use acids and solvents in this product. These products can
cause physical injuries to the operator and irreversible damage to
the machine.
Improper treatment of the pressure washer can damage it and
shorten its life.
 If you have questions about intended use, ask dealer or contact
Customer Service at [1] 919-550-3221.
 NEVER operate units with broken or missing parts, or without
protective housing or covers.
 DO NOT bypass any safety device on this machine.
 Before starting pressure washer in cold weather, check all parts of
the equipment to be sure ice has not formed there.
 NEVER move machine by pulling on high pressure hose. Use handle
provided on unit.
 This equipment is designed to be used with BEAST authorized parts
ONLY. If equipment is used with parts that DO NOT comply with
minimum specifications, user assumes all risks and liabilities.
CAUTION

7 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
PREPARATION & ASSEMBLY - Model P1450B, P1450B-CAN, P1500B, P1600B, P1600B-BB, P1600B-CAN, P1760B-BB
Assembly Time: 5 minutes
Tools Required: 17mm or Adjustable Wrench
Note: 17mm wrench (Part L pg. 3) is provided in hardware bag.
Surface Preparation
 Before starting any cleaning task, it is important to inspect the area
for objects which could create a hazard.
 Remove any objects from the work area which could be tripped
over, such as toys or outdoor furniture.
Step 1
 Remove or peel off blue protective film on the front of the pressure
washer and on the wands (if applicable). Also, remove any bubble
wrap. Discard blue protective film and bubble wrap.
Step 2
 Attach the Zinc Connect or Quick Connect Inlet coupling to water
supply inlet on pressure washer, as shown in Figure below.
 On some models the coupling or quick connect may be installed at
the factory for your convenience.
Step 3
 Attach Wand Bracket to the unit as shown in Figure below.
Step 4
 Attach High Pressure Hose to Main Unit as shown in Figure below.
Step 5
 Attach other end of High Pressure Hose to Gun as shown in Figure
below. Fasten tightly with 17mm wrench to avoid leakage.
Step 7
 Attach the hose holder strap to the side of the unit as shown in
Figure below.
Step 6
 Attach Tool Belt to the Strap Bracket as shown in Figure below.
 The belt bracket is secured by two provided screws to the machine
body.
 The bracket is installed at the factory on most models.
For Operating Instructions, proceed to page 9.

Rev: Jan 2018
8 of 18
®
BEAST Electric Pressure Washers
Step 3
 Attach the L-shape coupler end of the extension hose (F) into the
water outlet as shown in Figure below. Fasten tightly to avoid
leakage.
Step 4
 Attach the straight coupler end of the extension hose into the hose
reel inlet as shown in Figure below. Fasten tightly to avoid
leakage.
Step 2
 Attach the Zinc Connect or Quick Connect Inlet coupling to water
supply inlet on pressure washer as shown in Figure below.
 On some models the coupling or quick connect may be installed at
the factory for your convenience.
Step 6
 Attach the soap/detergent bracket. Bottle, siphon hose, as shown
in the Figure below.
PREPARATION & ASSEMBLY - Model P1750B, P1750B-CAN, P1800B, P1800B-BB, P1800B-CAN, P2000B-BB
Step 7
 Attach High Pressure Hose to Gun as shown in Figure below.
Fasten tightly with 17mm wrench to avoid leakage.
Step 8
 Attach foot bracket as shown in Figure below.
Step 5
 Attach the gun/wand holder as shown in the figure below.
Assembly Time: 5 minutes
Tools Required: 17mm or Adjustable Wrench
Note: 17mm wrench (Part L pg. 3) is provided in hardware bag.
Surface Preparation
 Before starting any cleaning task, it is important to inspect the area
for objects which could create a hazard.
 Remove any objects from the work area which could be tripped
over, such as toys or outdoor furniture.
Step 1
 Remove or peel off blue protective film on the front of the pressure
washer and on the wands (if applicable). Also, remove any bubble
wrap. Discard blue protective film and bubble wrap.
For Operating Instructions, proceed to page 9.

9 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
OPERATION
HOW TO USE THE PRESSURE WASHER
If you have any problems operating your pressure washer,
please call the pressure washer help-line at [1] 919-550-3221.
Pressure Washer Clearance
Prevailing winds and air currents should be taken into consideration
when positioning pressure washer.
 Keep spray nozzle between 8 to 24 inches away from cleaning
surface.
 Operate this unit on a stable surface.
 Be extremely careful if you must use the pressure washer from a
ladder, scaffolding or any other relatively unstable location.
 Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury if gun kicks back.
High pressure spray could cause you to fall if you are too
close to the cleaning surface.
WARNING
Water Supply (Cold Water Only):
 Do not draw non-water liquids through the unit. For use with cold
water supply only.
 Water hose must be at least a 1/2 inch diameter.
 Flow rate of water supply must not fall below 2GPM (gallons per
minute).
 Flow rate can be determined by running the water for one minute
into an empty 5-gallon container.
 The water supply temperature must not exceed 104°F
(40°C).
Step 1:
 Make sure that the ON/OFF switch is in the “OFF” position.
CAUTION:
 To prolong the life of the unit, it is recommended to rest the unit
5 minutes after every 30 minutes of use.
CAUTION:
 Never use the pressure washer to draw in water
contaminated with solvents (e.g. paint thinners, gasoline,
oil, etc.).
 Dirt in the feed water will damage the unit.
 To avoid this risk, we recommend checking
 the water filter (located inside the water inlet; to clean it
out see Maintenance section on page 13).
 Always prevent debris from being drawn into the unit by
using a clean water source and an accessory water filter if
required.
Step 2:
 Fasten the other end of the Zinc Connect to the or quick-connect
coupling onto the garden hose and then attach the quick-
connecting coupling to the inlet adaptor, as shown in the Figure
Step 3:
 Insert the desired wand into spray gun, and twist 1/4 turn until
rectangular tab appears.
The high pressure stream of water that this equipment produces
can pierce skin and its underlying tissues, leading to serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor is
stopped and water is disconnected, which can cause injury.
 Keep high pressure hose connected to pump and spray gun while
system is pressurized.
 ALWAYS point gun in safe direction and squeeze spray gun trigger,
to release high pressure, every time you stop engine. Engage
trigger lock when not in use.
WARNING
A pressure washer produces a high pressure spray which
increases risk of injury and damage to unit.
 Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.
 Before starting the pressure washer, be sure you are wearing
adequate eye protection.
Step 4:
 To use another wand, reverse Step 3 and insert desired wand by
repeating Step 3.

Rev: Jan 2018
10 of 18
®
BEAST Electric Pressure Washers
OPERATION
CAUTION
A pressure washer produces a high pressure spray which
increases risk of injury and damage to unit.
 Gun Kicks Back - Hold with both hands!
 The trigger gun safety lock prevents the trigger from accidentally
being engaged. The safety feature DOES NOT lock trigger in the ON
position.
 DO NOT secure spray gun in open position.
 DO NOT leave spray gun unattended while machine is running.
 NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.
 Always be certain spray gun, nozzles and accessories are correctly
attached.
Step 5:
 Attach garden hose to water supply and turn water on.
Step 6:
 Plug the unit into an outlet. Make sure that the pressure
washer is the only device plugged into the outlet.
If plugging
into a garage outlet, make sure there are no other devices plugged
into any other outlets in the garage..
Press “TEST”. Then press
“RESET” to assure proper connection to power.
Step 7
 IMPORTANT: Before turning the unit “ON”, depress the trigger to
bleed any trapped air out of the pump and hose.
Step 8
 Release trigger and start the pressure washer by turning ON/OFF
switch to ON.
 IMPORTANT: DO NOT turn the unit on without completing Step 7.
Step 9
Adjusting the spray
 Turning the nozzle allows the use of several different spray tips.
Each spray tip provides a different spray pattern as shown in Figure
below.
CAUTION:
 Jet spray adjustment is very aggressive. Do not adjust while
spraying. We recommend that for most cleaning applications, a 20
degree spray angle should be used to avoid damage to the surface
being sprayed.
To prolong the life of the unit, it is recommended to
rest the unit 5 minutes after every 30 minutes of use.
Wider
spray angle
Narrower
spray angle

11 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
WORKING WITH DETERGENTS
Working with detergent ensures a quick soaking of the dirt, and allows
the high-pressure water to penetrate and remove the dirt more
effectively. Always spray detergent on a dry surface. Do not pre-soak
area with plain water. Wetting the surface first dilutes the detergent
and reduces its cleaning ability.
To siphon and apply detergent, you must operate the pressure washer
on low pressure. This provides a gentle application of detergent, with
the pressure equivalent to a low-set garden hose. The high-pressure
setting is used for cleaning; you cannot apply detergents when working
at high-pressure. Always test detergent in an inconspicuous area before
use.
Use only detergents designed for use with pressure washers; all
detergents should be thin liquids, about the consistency of milk. Using
thicker liquids such as car wash concentrate or dish soap will not allow
the detergent to siphon.
Step 1
P1450B, P1500B, P1600B, P1760B: Attach yellow detergent bottle to
the spray gun as shown in Figure below.
Step 3
 Gently remove detergent container and fill with detergent.
 Re-attach containers back into position.
 Set pressure washer to low pressure by pulling the spray end of the
wand out/downward.
Step 4
Turn the pressure washer to “ON”. Pull trigger to operate the unit. The
liquid detergent will automatically mix with water and be discharged
through nozzle. Apply detergent to a DRY work surface, from bottom to
top.
Step 2
P1750B P1800B and P2000B ONLY: Set the adjustable nozzle
to the low-pressure setting. The nozzle must be set in the
low-pressure position to apply detergent. Apply low pressure
spray to a small area and then check surface for damage. If no
damage is found, you can assume it is okay to continue cleaning.
Start at top of area to be rinsed, working down with same
overlapping strokes as used for cleaning.
Damage may occur to painted surface if chemical is allowed to
dry on surface. Wash and rinse a small section at a time. Avoid
working on hot surfaces or in direct sunlight
Failure to clean properly will cause the injection system to
become clogged and inoperable.
Never use:
 Bleach, chlorine products and other corrosive chemicals
 Liquids containing solvents (i.e., paint thinners, gasoline,
oils)
 Tri-sodium phosphate products
 Ammonia products
 Acid-based products
These chemicals will harm the unit and will damage the surface
being cleaned..
Step 5
Allow detergent to remain on the surface for a short time before rinsing.
Do not allow detergent to dry on surface.
Step 6
Rinse with clean water under high-pressure. On a vertical surface, rinse
from the bottom up, then rinse from the top down to avoid streaking.
Hold nozzle 6-8 inch from the work surface at a° 45 angle.
Step 7 (End of detergent application)
When you have finished using the detergent injection system, remove
detergent suction tube from bottle and insert into 1 gallon (5L) of fresh
water. Siphon water at low-pressure for one to two minutes so that all
detergent is flushed through system. Remove detergent bottle and rinse
CAUTION
OPERATION
P1750B, P1800B, P2000B: Attach adjustable wand to spray gun.
Diagram for P1750B , P1800B, and P200B ONLY:

Rev: Jan 2018
12 of 18
®
BEAST Electric Pressure Washers
Step 2
Turn off the water supply.
Step 3
Press trigger to release water pressure for 20~30 seconds.
Step 4
Disconnect the garden hose from the water inlet on the unit.
Step 5
Disconnect the high-pressure hose from the high pressure outlet
and engage the gun safety lock.
Turn off water supply and squeeze trigger to depressurize
the unit. Failure to do so could result in personal injury due
to discharge of high-pressure water.
STEPPING AWAY OR TAKING A BREAK
If taking a break of five minutes or more:
1. Engage gun safety lock.
2. Turn pressure washer to “OFF” (O) position.
3. Unplug the power cord from the outlet.
CAUTION
Failure to follow the above directions will result in damage to the pump
assembly and accessories and will void the warranty. We recommend the use
of antifreeze (Pump Saver) to prevent cold weather damage during storage in the
winter months.
WARNING
OPERATION
Shutting Down and Cleaning Up
Step 1
Turn the switch to “OFF” (0) position and unplug cord from outlet.
It is recommended to store the unit indoors to prevent exposure
to freezing temperatures that may damage the pump.
You must protect your unit from freezing temperatures.
 Failure to do so may permanently damage your pump and render
your unit inoperable.
 Freeze damage is not covered under warranty.
CAUTION
Alternative Procedure
If you cannot perform the Optimum Winterizing procedure,
you can still protect your pressure washer from winter-damage:
1. Disconnect all water connections.
2. Turn on the machine for a few seconds. Press trigger to bleed any
remaining water in the pump. Turn off immediately.
3. Remove the gun and hose from the pressure washer. Drain any
excess water. Roll hose carefully and do not allow hose to be kinked.
4. Store the machine and accessories in a room that does not reach
freezing temperatures. Do not store near furnace or other hot areas as
it may dry out o-rings and pump seals.
STORING
Before storing the unit for an extended period. be sure the storage area
is free of excessive humidity and dust.
Storage Preparation for Pressure Washer
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and “freeze”
pump action. If you do not plan to use the pressure washer for
more than 30 days, follow this procedure:
1. Flush detergent injection hose by placing filter into a pail of
clean water while running pressure washer in low pressure
mode. Flush for one to two minutes.
2. Turn the on/off switch to “OFF” and unplug the unit.
3. Turn off the water supply and disconnect the hose from the
unit.
4. Empty the unit of liquids by squeezing the trigger on the gun
and holding until no more water comes from the pump.
Failure to depressurize the unit could result in personal injury
due to high pressure water discharge.
5. Ensure pump is clean and empty to prevent corrosion build up
and freezing of pump components.
6. Store unit in a clean, dry area.
Winterizing and Long Term Storage

13 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
OPERATION
YOU MUST PROTECT YOUR UNIT FROM
FREEZING TEMPERATURES
 Failure to do so may permanently damage your pump and render your unit inoperable.
 Freeze damage is not covered under warranty.
TO PREVENT PREMATURE WEAR ON PRESSURE
WASHER PUMP, DO NOT ALLOW UNIT TO RUN MORE
THAN 30 MINUTES AT A TIME
CAUTION
CAUTION!

Rev: Jan 2018
14 of 18
®
BEAST Electric Pressure Washers
MAINTENANCE
GENERAL MAINTENANCE RECOMMENDATIONS
The pressure washer warranty does not cover items that have been
subjected to operator abuse or negligence. To receive full value from the
warranty, the operator must maintain the pressure washer as instructed
in this manual.
NOTE: Should you have questions about replacing components on your
pressure washer, please call [1] 919-550-3221 for assistance.
 All maintenance in this manual should be made at least once each
season.
Before Each Use
1. Check water inlet screen for damage.
2. Check high pressure hose for leaks.
3. Check detergent siphoning tube and filter for damage.
4. Check spray gun, nozzle extension, and nozzles for leaks.
5. Rinse out garden hose to flush out debris.
The high pressure stream of water that this equipment produces
can pierce skin and its underlying tissues, leading to serious
injury and possible amputation.
 NEVER repair high pressure hose. Replace it.
 Replacement hose rating MUST exceed maximum pressure rating
of unit.
WARNING
Check Detergent Siphoning Tube
Examine the filter on the detergent tube and clean if clogged. The tube
should fit tightly on the barbed fitting. Examine the tube for leaks or
tears. Replace the filter or tube if either is damaged.
Check Gun and Nozzle Extension
Examine the hose connection to the spray gun and make sure it is
secure. Test the trigger by pressing it and making sure it springs back
into place when you release it. Put the trigger lock in the on position and
test the trigger. You should not be able to press the trigger.
Check High Pressure Hose
The high pressure hose can develop leaks from wear, kinking, or abuse.
Inspect the hose each time before using it. Check for cuts, leaks,
abrasions or bulging of cover, damage or movement of couplings. If any
of these conditions exist, replace the hose immediately.
Adjustable Nozzle Maintenance
Surging, or pulsing sensation, felt while squeezing the spray gun trigger
may be caused by excessive pump pressure. The principal cause of
excessive pump pressure is a nozzle clogged or restricted with foreign
materials, such as dirt, etc. To correct the problem, immediately clean
the nozzle using the tools included with your pressure washer and
follow these instructions:
1. Shut off pressure washer and turn off water supply.
2. Depressurize unit by squeezing trigger with wand away from face.
3. Remove wand from gun
4. Use needle included in kit to free any foreign material clogging or
restricting spray tip, see Figure below.
Connections
Connections on pressure washer hoses, gun and spray wand should be
cleaned regularly and lubricated with non-water soluble grease.
Adjustable Nozzle
For the adjustable nozzle, you can also lubricate the nozzle collar (high-
pressure low-pressure) by using non-water soluble grease regularly.
Water Filter Screen
The pressure washer is equipped with a water inlet filter that prevents
debris going into the pump. If the filter is not kept clean, the flow of
water to the pressure washer will be restricted and the pump may be
damaged.
1. To clean the screen, remove quick connector and remove the filter
screen from the pump inlet.
O–Ring Maintenance
Through the normal operation of your pressure washer, o–rings, which
keep the connections of the hoses and spray gun tight and leak–free,
may become worn or damaged. They should be lubricated with non-
water soluble grease.
2. Rinse filter screen with warm water until it is free of debris and
blockage. Check for any damage, replace if damaged.
3. Reinstall screen and quick-connector immediately.
Air Vents
The air vents located on the front and back of the pressure washer must
be kept clean and free of any obstructions to ensure proper air-cooling
of the motor during operation.
The high pressure stream of water that this equipment produces
can pierce skin and its underlying tissues, leading to serious
injury and possible amputation.
 NEVER repair leaking connections with sealant of any kind. Replace
o-ring or seal.
WARNING

15 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
Tips for Cleaning
CAUTION
 Before cleaning any surface an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results.
 If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.
 When using on surfaces which might come in contact with food, flush surfaces with plenty of drinking water.
Decks
Pre-rinse deck and surrounding area with fresh water. If using
detergent, apply to surface at low pressure. For best results, limit your
work area to smaller sections of approximately 25 square feet. Allow
detergent to remain on surface 1-3 minutes. Do not allow detergent to
dry on surface. Rinse at high pressure in a long sweeping motion
keeping the spray nozzle approximately 3-6 inches from the cleaning
surface. Always clean from top to bottom and from left to right. When
moving on to a new section of the cleaning surface, be sure to overlap
the previous section to eliminate stop marks and ensure a more even
cleaning result.
House Siding
(Pre-rinse cleaning surface with fresh water. If using detergent, apply to
surface at low pressure (for best results, limit your work area to
sections of approximately 6 feet and always apply detergent from
bottom to top). Allow detergent to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface, if surface appears to be drying,
simply wet down surface with fresh water. If needed, use special wash
brush attachment (not included) to remove stubborn dirt. Rinse at high
pressure from top to bottom in an even sweeping motion keeping the
spray nozzle approximately 6 inches from the cleaning surface.
Patio and Lawn Furniture
Pre-rinse furniture and surrounding area with fresh water. If using
detergent, apply to surface at low pressure. Allow detergent to remain
on surface 1-3 minutes. Do not allow detergent to dry on surface. If
needed use special Wash Brush attachment (not included) to remove
stubborn dirt. Rinse at high pressure in a sweeping motion keeping the
spray nozzle approximately 3-6 inches from the cleaning surface. For
best results, clean from top to bottom and from left to right.
TROUBLESHOOTING
Symptom Cause Solution
Motor will not start On/Off switch is in the “OFF” (0) position. Turn switch to the “ON” position
Power cord is not plugged in. Plug in power cord.
Electrical outlet does not supply adequate power. Try a different outlet.
Tripped GFCI plug. Press “RESET” button on GFCI plug.
Tripped circuit breaker. Switch off pressure washer. The reset comes automatically once the
temperature of the unit drops.
Plugged Wand Turn unit off. If wand is plugged, then the water will be at full
pressure making disconnecting wand difficult. Carefully disconnect
wand and/or gun, clean wand.
Unit does not reach high pressure. Diameter of garden hose is too small. Replace with a 5/8 inch or larger garden hose.
Water supply is restricted. Check garden hose for kinks, leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in warm water.
Spray wand is on low pressure position Turn spray wand to high pressure position (See p.10)
Troubleshooting continued on next page...
Automobiles, RV’s, Boats, Motorcycles, ATV’s
Pre-rinse vehicle with fresh water. If using detergent, apply to surface at
low pressure. For best results, clean one side of vehicle at a time and
always apply detergent from bottom to top, do not allow detergent to
dry on surface. If needed, use special wash brush attachment (not
included) to remove stubborn dirt. Rinse at high pressure in a sweeping
motion keeping the spray nozzle approximately 6-8 inches from the
cleaning surface (distance should increase when rinsing pin-striping or
other sensitive surfaces). Always clean from top to bottom and from left
to right. For best results, wipe surface dry with a chamois or soft dry
cloth.
BBQ Grills, Gardening Tools, Mowers/Trimmers
Pre-rinse cleaning surface with fresh water. If using detergent or
Degreaser, apply detergent at low pressure. Allow detergent to remain
on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse
at high pressure keeping the spray nozzle approximately 3-6 inches from
the cleaning surface. For removing extremely stubborn dirt, it may be
necessary to move the spray nozzle even closer to the surface for
greater dirt cutting action.
Driveway, Sidewalks, Patios, Brick
Pre-rinse cleaning surface with fresh water. If using detergent or
Degreaser, apply to surface at low pressure. For best results, limit your
work area to smaller sections of approximately 25 square feet. Allow
detergent or Degreaser to remain on surface 1-3 minutes. Do not allow
detergent to dry on surface. Rinse at high pressure in a sweeping
motion keeping the spray nozzle approximately 3-6 inches from the
cleaning surface. Always clean from top to bottom and from left to
right. For removing extremely stubborn stains, use the Turbo Nozzle.

Rev: Jan 2018
16 of 18
®
BEAST Electric Pressure Washers
TROUBLESHOOTING (continued)
IF YOU ENCOUNTER ANY ADDITIONAL DIFFICULTIES NOT LISTED, CALL CUSTOMER SERVICE AT
[1] 919-550-3221 FOR ASSISTANCE.
Symptom Cause Solution
Output pressure varies high and low. Not enough inlet water supply. Turn water on full force. Check garden hose for kinks,
leaks or blockage.
Pump is sucking air. Check that hoses and fittings are air tight. Turn off ma-
chine. Purge pump by squeezing trigger gun until a
steady flow of water emerges through the nozzle.
Water inlet filter is clogged. Remove filter and rinse out in warm water.
Discharge nozzle is obstructed. Blow out or remove debris with a fine needle.
Calcified gun, hose or spray wand. Run distilled vinegar through detergent suction tube.
No detergent. Detergent suction tube not properly connected to
the machine.
Check connection.
Detergent is too thick. Dilute detergent, for best results use recommended
detergent.
Filter on detergent suction tube is clogged. Run warm water through filter to remove debris.
Damaged or clogged detergent suction tube. Remove obstruction or replace detergent suction tube.
Spray wand is in high pressure position. Turn spray wand tip to low pressure position.
Discharge nozzle is obstructed. Blow out or remove
Garden hose connection leaks. Loose fittings. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand, or extension, or nozzle leaks. Spray nozzle not properly attached. Insert the spray nozzle into the trigger Carefully press in
against the spring tension and twist into the locked
position.
Broken o-ring or plastic insert. Call Customer Support
Pump is noisy. Pump is sucking air. Check that hoses and fittings are air tight. Turn off
machine and purge pump by squeezing trigger gun until a
steady flow of water emerges through the nozzle.
Water leaks from pump (up to 10 drops per
minute is permissible).
Loose fittings. Check that all fittings are tight.
Water seals are damaged or worn. Call Customer Support
Oil Drips. Oil seals are damaged or worn. Call Customer Support
Motor buzzes but fails to run. Supply voltage below minimum. Verify that only the pressure washer is running on this
circuit.
System has residual pressure. Turn unit “OFF”, squeeze trigger on spray want to release
pressure, then turn unit “ON”.
Voltage loss due to extension cord. Do not use extension cord with this unit—plug directly
into power outlet.
Pressure washer not used for long periods Call Customer Service.

17 of 18
®
BEAST Electric Pressure Washers
Rev: Jan 2018
Part/Description Part Number Price
Spray Gun SP00109 $30.00
Adjustable Wand (P1450B, P1500B, P1600B, and P1760B) SP00209 $30.00
Adjustable Wand (P1750B, P1800B, and P2000B) SP00309 $30.00
Turbo Wand SP00409 $30.00
Straight Brush SP00809 $30.00
Rotary Brush SP00709 $30.00
Soap Injector Bottle (P1450B, P1500B, P1600B, and P1760B) SP00909 $30.00
Soap bottle and Bracket (P1750B, P1800B, and P2000B) SP01809 $30.00
Gun Holder (P1450B, P1500B, P1600B, and P1760B) SP01009 $30.00
Gun and Wand Holder (P1750B, P1800B, and P2000B) SP01409 $30.00
High Pressure Hose (P1450B, P1500B, P1600B, and P1760B) SP00509 $30.00
High Pressure Hose (P1750B, P1800B, and P2000B) SP02412 $30.00
Extension Hose (P1750B, P1800B, and P2000B) SP01509 $25.00
Zinc Connect SP04212 $10.00
Plastic Quick Connect SP02509 $8.00
Brass Quick Connect SP01309 $15.00
Hose Strap (P1450B, P1500B, P1600B, and P1760B) SP01209 $20.00
Tool Belt (P1450B, P1500B, P1600B, and P1760B) SP01109 $45.00
Hose Reel (P1750B, P1800B, and P2000B) SP01609 $45.00
Hose Reel Handle (P1750B, P1800B, and P2000B) SP01709 $40.00
Foot Rest (P1750B, P1800B, and P2000B) SP01909 $25.00
Hardware Bag Includes:
 17mm Wrench
 Spare Water Filter
 Spare O-Rings
 Cleaning Needle
 Product Manual
SP00609 $20.00
Spare Parts List for Beast Electric Pressure Washers
To order spare parts, visit ServiceandWarrantyOnline.com to place an order, or fill out the “Spare Parts Order Form” included in your product’s packag-
ing. Be sure to include all billing and shipping information and fax the order to [1] 919-550-3277 or call [1] 919-550-3221 .
All sales are final. To check on an order status, please call [1] 919-550-3221 or email [e-mail].

Limited Warranty & Service
LIMITED 1 YEAR WARRANTY
TERM OF THIS WARRANTY:
This pressure washer is warranted to be free of defects in materials and workmanship under normal residential use for a period of 1 year. This warranty applies to the
electric motor and the pump for 1 year. (Normal wear and maintenance items such as the cord, GFCI breaker, wand, hose, tips, seals, and other attachments are
warranted for 90 days.) Warranty repairs will be made without charge for parts and labor for the first 90 days from the date of purchase. After the first 90 days, this
limited warranty covers the costs of replacement parts on the pressure washer unit only. Any commercial, industrial or rental use of the product will reduce the term of
this warranty to 30 days for all components.
TO QUALIFY FOR THIS WARRANTY:
The product must be purchased in the United States, Canada or Mexico from a retail store authorized by GXi Outdoor Power Equipment LLC to sell the product. This
warranty applies to first retail purchaser / owner during the applicable warranty time period. A proof of purchase receipt showing date of purchase and authorized retail
store and a valid product serial number are required to demonstrate warranty eligibility.
WHAT GXI PARTS AND SERVICE LLC WILL REPAIR OR REPLACE UNDER WARRANTY:
GXI PARTS AND SERVICE LLC will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the
applicable warranty time period subject to the exclusions stated herein. This warranty is void if the owner fails to follow the prescribed maintenance and operating
procedures described in this manual. Only failures where an identifiable manufacturing defect can be identified will be covered under the terms of this warranty.
GXI PARTS AND SERVICE LLC has the right to recover warranty administration costs from the owner if the root cause of the malfunction was found to be other than
defective material or workmanship. Anything replaced under warranty becomes the property of GXI PARTS AND SERVICE LLC. Parts replaced under warranty will be
considered as part of the original product and any warranty on those parts will expire coincident with the original product warranty.
TO OBTAIN WARRANTY SERVICE:
Contact GXI PARTS AND SERVICE LLC to obtain warranty return authorization and directions as to where to send your product for evaluation. Have your proof of
purchase and the product serial number available when you call.
If you are not satisfied with warranty service, contact GXi PARTS AND SERVICE LLC. If you are unable to resolve problems and require further assistance, write to GXI
PARTS AND SERVICE LLC Customer Service.
EXCLUSIONS:
THIS WARRANTY DOES NOT EXTEND TO PARTS AFFECTED OR DAMAGED BY ACCIDENT AND/OR COLLISION, NORMAL WEAR, CONTAMINATION, USE IN AN
APPLICATION FOR WHICH THE PRODUCT WAS NOT DESIGNED OR ANY OTHER MISUSE, NEGLECT, INCORPORATION OR USE OF UNSUITABLE ATTACHMENTS OR
PARTS, UNAUTHORIZED ALTERATION, OR ANY CAUSES OTHER THAN DEFECTS IN MATERIAL OR WORKMANSHIP OF THE PRODUCT. IN PARTICULAR, THIS
WARRANTY DOES NOT COVER DAMAGE CAUSED BY FAILURE TO FOLLOW PRESCRIBED WARNINGS AND OPERATING PRACTICES; FAILURE TO FOLLOW PROPER
MAINTENANCE AND STORAGE PROCEDURES; AND PHYSICAL DAMAGE DUE TO SHIPPING, HANDLING OR STORAGE.
DISCLAIMER OF CONSEQUENTIAL DAMAGE AND LIMITATION OF IMPLIED WARRANTIES:
GXI PARTS AND SERVICE LLC DISCLAIMS ANY RESPONSIBILITY FOR LOSS OF TIME OR USE OF THE PRODUCT, TRANSPORTATION, COMMERCIAL LOSS, OR ANY
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGE. ANY IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS WRITTEN LIMITED WARRANTY.
THIS WARRANTY IS VOID IF THE MANUFACTURING DATE AND THE SERIAL NUMBER ON THE EQUIPMENT HAS BEEN REMOVED OR THE EQUIPMENT HAS BEEN
MODIFIED.
Commercial Lawn Mowers Heavy Duty Pressure Washers Chipper Shredders Generator Accessories