Stanley Lismore User manual

Lismore Non Boiler Solid Fuel Stove
INSTALLATION AND OPERATING INSTRUCTIONS
This applian e is hot while in operation and retains its heat for a long period of time after use. Children,
aged or infirm persons should be supervised at all times and should not be allowed to tou h the hot
working surfa es while in use or until the applian e has thoroughly ooled.
When using the stove in situations where hildren, aged and/or infirm persons are present a fireguard
must be used to prevent a idental onta t with the stove. The fireguard should be
manufa tured in a ordan e with BS 8423:2002.

TABLE OF CONTENTS
AGENO.
1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Fire Cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Asbestos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Metal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Flues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Flue Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Flue Exit - Top & Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5. Flue Orientation Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6. Chimney . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
7. Installation Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8. Ventilation & Combustion Air Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
9. Permanent Air Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
10. External Ducted Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
11. Heat Recovery Ventilation (HRV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
12. CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13. Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. Floor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
15. Flue Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
16. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
17. Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
18. Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
19. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
20. Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
21. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
22. Recommended Fuels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
23. Air Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Primary Air Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Secondary Air Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
24. De-Ashing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
25. Disposal of Ashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
26. To Clean Chimney Back Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
27. Changing Grate Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
28. Fire Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
29. Vitreous Enamel Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
30. Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
31. Glass Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
32. Summer Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
33. Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
34. Installation Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1

THE LISMORE SOLID FUEL NON BOILER STOVE
INSTALLATION & O ERATING INSTRUCTIONS
GENERAL
When installing, operating and maintaining your
Lismore Stove respect basic standards of fire safety.
Read these instructions carefully before commenc-
ing the installation. Failure to do so may result in
damage to persons and property. Consult your local
Municipal office and your insurance representative
to determine what regulations are in force. Save
these instructions for future reference.
Please note that it is a legal requirement under
England & Wales Building Regulations that the
installation of the stove is either carried out under
Local Authority Building Control approval or is
installed by a Competent Person registered with a
Government approved Competent Persons
Scheme. HETAS Ltd operate such a scheme and a
listing of their Registered Competent Persons can
be found on their website at www.hetas.co.uk.
Special care must be taken when installing the stove
such that the requirements of the Health & Safety at
Work Act are met.
Handling
Adequate facilities must be available for loading,
unloading and site handling.
Fire Cement
Some types of fire cement are caustic and should
not be allowed to come into contact with the skin. In
case of contact with the skin wash immediately with
plenty of water.
Asbestos
This stove contains no asbestos. If there is a possi-
bility of disturbing any asbestos in the course of
installation then please seek specialist guidance and
use appropriate protective equipment.
Metal Parts
When installing or servicing this stove care should
be taken to avoid the possibility of personal injury.
“IM ORTANT WARNING”
This stove must not be installed into a chimney that
serves any other heating appliance.
2
The complete installation must be done in accor-
dance with current Standards and Local Codes. It
should be noted that the requirements and these
publications may be superseded during the life of
this manual.
Please re er to the current standards, BS EN 15287-
1:2007 Design, Installation and Commissioning o
chimneys.
FLUES
Flues should be vertical wherever possible and
where a bend is necessary, it should not make an
angle of more than 45owith the vertical. Horizontal
flue runs should be avoided except in the case of a
back outlet from the appliance, when the length of
the horizontal section should not exceed 150mm.
In order to minimise flue resistance and to make
sweeping easier it is recommended to use 2 x 45o
bends rather than a 90obend.
The flue termination point must be located to min-
imise any wind effects. Wind effects of suction,
pressure zones and turbulence can be created by
the roof and adjacent objects. Wind effects can also
be created by natural land contours.
To minimise the wind effects, the flue termination
point should be located a minimum of 1000mm from
the roof measured vertically and 2300mm measured
horizontally. Where this termination point does not
suffice it may be necessary to extend the flue pipe
so that the termination point is above the apex. (See
Fig.1)
Fig.1
2300
Appliance Soot Door
1000

FLUE I ES
A flue pipe should only be used to connect an appli-
ance to a chimney and should not pass through any
roof space.
Flue pipes may be of any of the following materials:
* Cast iron as described in BS 41:
1973 (1981), or
* Stainless steel with a wall thickness
of at least 1mm and as described in
BS EN 10095:1999 Specification for
stainless and heat resisting steel
plate, sheet and strip, for Grade 316
S11, 316 S13, 316 S16, 316 S31,
316 S33, or the equivalent
Euronorm 88-71 designation, or
* Vitreous enamelled steel complying
with BS 6999: 1989.
Flue pipes with spigot and socket joints should be fit-
ted with the socket uppermost.
Clearance to combustibles must be adhered to
when fitting the flue pipe.
The appliance is suitable for intermittent operation
on solid mineral fuel and intermittent operation on
wood logs.
3
Fig.3
FLUE EXIT (TO & REAR)
The stove is designed to allow the chimney be
cleaned through the stove. A means must be provid-
ed to clean the chimney such as a soot box/access
door in the flue for cleaning. See Fig.2 for recom-
mended locations. Fit it to the stove as shown in
Fig.2.
The stove is supplied with a reversible flue spigot for
use with both top outlet and rear outlet. Fit the spig-
ot as per Fig.3 for top outlet and as per Fig.4 for rear
outlet.
Fig.2
Flue Liner
Sleeve
Flue ipe
ossible
ositions
for access
Flue
Soot Door
Appliance Flue
Outlet
Appliance
Debris Collection
space
FLUE ORIENTATION ASSEMBLY

Fig.4 The outlet from the chimney should be above the
roof of the building in accordance with the provisions
of Building Regulations Approved Document J.
CHIMNEY
Do not connect to a chimney serving another
appliance.
The stove is a radiant room heater and must be con-
nected to a chimney of the proper size and type.
The chimney must have a cross-sectional area of at
least 30 square inches 19350sq. mm or a diameter
of at least 6” (150mm). It is best to connect to a
chimney of the same size, as connection to a larger
size may result in a somewhat less draught. Do not
connect to a chimney serving another appliance.
An existing masonry chimney should be inspected
and if necessary repaired by a competent mason.
In adverse weather conditions, down drafts may be
experienced causing smoke or fumes to spill into the
room. If this occurs shut the appliance down by
closing the air controls. If the problem persists seek
the advice of a chimney sweep.
In order for the stove to perform satisfactorily the
chimney height must be sufficient to ensure an ade-
quate draught of approximately 12 Pa so as to clear
the products of combustion and prevent smoke
problems into the room, poor draught conditions will
result in poor performance.
NOTE: A chimney height of not less than 4.5 metres
measured vertically from the outlet of the stove to
the top of the chimney should be satisfactory.
Alternatively the calculation procedure given in EN
13384-1 may be used as the basis for deciding
whether a particular chimney design will provide suf-
ficient draught.
4
Fig.5
Fig.6

If installation is into an existing chimney then it must
be sound and have no cracks or other faults which
might allow fumes into the house. Older properties,
especially, may have chimney faults or the cross
section may be too large i.e. more than 200mm
diameter. Remedial action should be taken, if
required, seeking expert advice, if necessary. If it is
found necessary to line the chimney then a flue liner
suitable for solid fuel must be used in accordance
with Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction
and have been swept clean immediately before
installation of the stove. If the stove is fitted in place
of an open fire then the chimney should be swept
one month after installation to clear any soot falls
which may have occurred due to the difference in
combustion between the stove and the open fire.
If there is no existing chimney then any new system
must be to the designation described above and in
accordance with Building Regulations Approved
Document J.
A single wall metal fluepipe is suitable for connecting
the stove to the chimney but is not suitable for use
as the complete chimney. The chimney and con-
necting flue must have a minimum diameter of
150mm and at no point must the diameter reduce to
less than the size of the outlet socket of the stove.
Any bend in the chimney or connecting fluepipe
should not exceed 45o. 90obends should not be
used.
Fig.7
Fig.8
Combustible material should not be located where
the heat dissipating through the walls of fireplaces or
flues could ignite it. Therefore when installing the
stove in the presence of combustible materials due
account must be taken of the guidance on the sepa-
ration of combustible material given in Building
Regulations Approved Document J and also in these
stove instructions. See Figs, 9,10,11,12,13 &14 .
5
Max. Horizontal Run

Fig.9
Fig.10
Fig.11
Fig.12
Fig.13
Fig.14
6
CLEARANCE TO COMBUSTIBLES
CORNER INSTALLATION
ALCOVE INSTALLATION FIRE LACE INSTALLATION
FLUE CLEARANCES
MINIMUM COMBUSTIBLE ALCOVEMANTLE CLEARANCE

If it is found that there is excessive draught in the
chimney then a draught stabiliser should be fitted.
Fitting of a draught stabiliser will affect the require-
ment for the permanent air supply into the room in
which the stove is fitted in accordance with
Approved Document J (see also combustion air sup-
ply).
Adequate provision e.g. easily accessible soot door
or doors must be provided for sweeping the chimney
and connecting fluepipe.
ALL FLUE INSTALLATIONS ARE THE
RES ONSIBILITY OF THE CUSTOMER.
INSTALLATION CLEARANCES
Maintain at least the following clearances to all
combustible material:
VENTILATION & COMBUSTION AIR
REQUIREMENTS
It is imperative that there is sufficient air supply to
the stove in order to support correct combustion.
The air supply to this appliance must comply with
current Building Regulations. The minimum effec-
tive air requirement for this appliance is 33cm2. This
increases to 51cm2where a flue draft stabiliser is fit-
ted. If another air using appliance is fitted in an adja-
cent room it will be necessary to calculate an addi-
tional air supply.
All materials used in the manufacture of air vents
should be such that the vent is dimensionally stable,
corrosion resistant, and no provision for closure.
The effective free area of any vent should be ascer-
tained before installation. The effect of any grills
should be allowed for when determining the effective
free area of any vent.
Air vents direct to the outside of the building should
be located so that any air current produced will not
pass through normally occupied areas of the room.
An air vent outside the building should not be locat-
ed less than the dimensions specified within the
Building Regulations and B.S. 8303: Part 1 from any
part of any flue terminal. These air vents must also
be satisfactorily fire proofed as per Building
Regulations and B.S. 8303: Part 1.
Air vents in internal walls should not communicate
with bedrooms, bedsits, toilets, bathrooms or rooms
containing a shower.
Air vents traversing cavity walls should include a
continuous duct across the cavity. The duct should
be installed in such a manner as not to impair the
weather resistance of the cavity.
Joints between air vents and outside walls should be
sealed to prevent the ingress of moisture. Existing
air vents should be of the correct size and unob-
structed for the appliance in use. If there is an
extraction fan fitted in adjacent rooms where this
appliance is fitted, additional air vents will be
required to alleviate the possibility of spillage of
products of combustion from the appliance/flue
while the fan is in operation. Refer to B.S. 8303 Part
1.
Where such an installation exists, a test for spillage
should be made with the fan or fans and other appli-
ances using air in operation at full rate, (i.e.extrac-
tion fans, tumble dryers) with all external doors and
windows closed.
If spillage occurs following the above operation, an
additional air vent of sufficient size to prevent this
occurrence must be installed.
Espe ially Airtight Properties:-
If the stove is being fitted in a property where the
design air permeability is less than 5m3/ (h.m2) (nor-
mally newer properties built from 2006), then a per-
manent ventilation must be fitted to provide 550mm2
of ventilation for each kW of rated output. If a
draught stabiliser is also fitted then the requirement
is 850mm2per kW of rated output.
ERMANENT AIR VENT
The stove requires a permanent and adequate air
supply in order for it to operate safely and efficiently.
In accordance with current Building Regulations the
installer will have fitted a permanent air supply vent
into the room in which the stove is installed to pro-
vide combustion air. This air vent should not under
any circumstances be shut off or sealed.
Extra tor Fan
There must not be an extractor fan fitted in the same
room as the stove as this can cause the stove to
emit smoke and fumes into the room.
7
From the Front 910mm (36”)
From the Back (with heat shield fit-
ted)
305mm (12”
From the Sides 560mm (22”)
From the Flue Pipe (Vertical no heat
shield fitted)
910mm (36”)
Mantle Clearance 760mm (30”)
Side Trim Clearance 560mm (22”)
Brick wall minimum clearance, but allow access for
controls and servicing. See Figs 9,10,11,12,13,14.

EXTERNAL DUCTED AIR
The primary air supply can be ducted from outside.
An aluminium flexible duct is available to order for
connection to the stove.
It is recommended to bring the air supply for the
stove into the house using a 4” plastic pipe. Where
the pipe meets the outside wall make sure a vent
cover is fitted properly to ensure no rodents can
enter via the vent pipe.
The vent pipe should be located to prevent the
ingress of moisture and in a location where it will not
get blocked with leaves or any other debris. As wind
effects can create suction and pressure zones of
opposite sides of the dwelling it is recommended to
run the air vent from opposite poles (North, South,
East & West) of the dwelling and tee off for the air
supply to the stove. This should negate the effect
of suction and pressure zones. See Fig.15
Fig.15 Note: When Installing
outside air pipe adhere
to ‘Clearance to
Combustible’ Section.
HEAT RECOVERY VENTILATION
Where a stove is to be installed in a dwelling with
Heat Recovery Ventilation (HRV) a number of
precautionary measures must be undertaken:
Should for example the delivery fan in the HRV unit
fail and the extraction fan in HRV fan continue to
run the HRV may create a pressure less than
atmospheric, this low pressure will effect the flue
pressure which is required to safely evacuate the
products of combustion from the stove.
1. Fit an adequately sized vent in the room to pre-
vent pressure less than atmospheric occurring.
The size should be established by closing all
windows and doors and then creating the
possible failure situation. Then open a window
in the room where the stove is fitted, slowly
until the pressure reaches atmospheric. The
size of the window opening should be
measured and a vent of the corresponding size
installed.
2. Fit a CO Alarm which has been approved to
EN 50291.
CO ALARM
Waterford Stanley recommend the fitting of a CO
Alarm in the same room as the appliance, this is a
requirement under U Building Regulations.
Further guidance on the installation of a carbon
monoxide alarm is available in BS EN 50292:2002
and from the alarm manufacturers instructions.
rovision of an alarm must not be considered a
substitute for either installing the appliance
correctly or ensuring regular servicing and
maintenance of the appliance and chimney
system.
WARNING:-
If the CO Alarm sounds unexpectedly:-
1. Open Doors and windows to ventilate the
room and then leave the premises.
2. Let the fire go out.
8

LOCATION
There are several conditions to be considered in
selecting a location for your Stanley Lismore Stove.
a. Position in the area to be heated, central
locations are usually best.
b. Allowances for proper clearances to
combustibles.
FLOOR ROTECTION
It is recommended that this appliance is installed on
a solid, level, non combustible hearth conforming to
current Building Regulations.
It is recommended that a minimum clearance of
100mm be maintained from the sides and rear of the
appliance to a tiled fireplace or masonry wall, espe-
cially on the right of the appliance as access is
required for the controls. See Fig.16.
FLOOR ROTECTION
FLUE LOCATIONS
Flue outlet to suit 152mm (6”) internal diameter flue
pipe.
Fig.17
Damper
Lever
Flue
Outlet
Air Inlet
9
Fig.16
280
100
100
100

TECHNICAL DATA
MANUFACTURED SMOKELESS
FUEL
WOOD
Max Output: (kW)
Room
10.6 kW
Room
11 kW
Typical refuelling intervals to obtain nominal
outputs:
MSF 1 hour WOOD .75 hrs
Mean Flue Gas Temperature oC393 328
Flue Gas Mass Flue 8.5 7.6
Gross Weight: 200 kgs
Flue Outlet: 150mm
Efficiency 70.4% 77%
Flue Draught: 12 Pa
Log Size: 340mm
S ECIFICATION
Fig18
Fig18a
Note: Dimensions stated are in millimetres unless otherwise stated and may be subject to a slight +/- variation.
10
WARNING: DO NOT OBSTRUCT RIMARY AIR SU LY TO THE STOVE
266
535
757
89
664
551
571

HANDOVER
On completion of the installation allow a suitable
period of time for any fire cement and mortar to dry
out, when a small fire may be lit and checked to
ensure the smoke and fumes are taken from the
stove up the chimney and emitted safely to the
atmosphere. Do not run at full output for at least 24
hours.
Ensure that the operating instructions for the stove
are left with the customer. Ensure to advise the cus-
tomer on the correct use of the appliance with the
fuels likely to be used on the stove and warn them to
use only the recommended fuels for the stove.
Advise the user what to do should smoke or fumes
be emitted from the stove. The customer should be
warned to use a fireguard to BS 6539 in the pres-
ence of children, aged and/or infirm persons.
11

IM ORTANT NOTES
Now that your Solid Fuel Stove is installed and no doubt you are looking forward to many comforts it will pro-
vide, we would like to give you some tips on how to get the best results from your stove.
1. We would like if you could take some time to read the operating instructions/hints, which we are
confident, will be of great benefit to you.
2. Do not burn fuel with a high moisture content, such as a damp peat or unseasoned timber. This will
only result in a build up of tar in the stove and in the chimney.
3. Clean the flue-ways of the stove weekly and ensure that there are no blockages. Check flueways
before lighting especially after a shut down period. lease refer to manual for instructions.
4. Always ensure ashpan lid is removed from ashpan before lighting the stove.
5. Before loading fresh fuel into the firebox, riddle fully to remove all ashes this will allow better and
cleaner burning. See Re-Fuelling section.
6. Never allow a build up of ashes in the ash pan, as this will cause the grate to burn out prematurely.
Empty the ashpan when refuelling.
7. Allow adequate air ventilation to ensure plenty of air for combustion.
8. Do not use as an incinerator burning rubbish/household waste.
9. Do not operate the stove with the ash-door open as this will over heat the unit causing unnecessary
damage.
10. Clean the chimney at least twice a year.
11. Burning soft fuels such as timber and peat will stain the glass. Regular cleaning will prevent
permanent staining. Clean with soapy water when cool.
12. eep all combustible materials a safe distance away from unit, please see section for clearances
to combustibles.
14. Do not use an aerosol spray on or near the stove when it is alight.
15. For safety reasons never leave children or the elderly unaccompanied while stove is in use. Use a
fire guard.
16. Avoid contact with the appliance when in use as stove reaches very high operating temperatures.
17. This appliance should be regularly maintained by a competent service engineer.
Use only replacement parts recommended by Stanley. Making unauthorised modifications, or using unautho-
rised parts will invalidate your guarantee and may cause damage or injury.
FUEL CALORIFIC VALUES - SOLID FUELS
Anthracite 25-50mm C.V.: 8.2kW/ g 14,000 BTUs/lb
House Coal 25-75mm C.V.: 7.2kW/ g 12,000 BTUs/lb
Timber - Firebox size C.V.: 5.0kW/ g 8,600 BTUs/lb
Peat Briquettes C.V.: 4.8kW/ g 8,300 BTUs/lb
AN ODOUR WILL EMIT FROM STOVE ON FIRST FIRING, WHEN FIRE REACHES MAXIMUM
TEM ERATURE OVER A NUMBER OF HOURS THE ODOUR WILL SUBSIDE.
IT IS BEST ADVISED TO O EN WINDOWS DURING THIS ERIOD.
THE ODOUR IS UN LEASANT BUT NOT TOXIC. YOU MAY WISH TO VACATE THE ROOM WHILE THE
AINT CURES.
12

LIGHTING
1. Open firedoor and open the primary air inlet by lowering the lever on the rear of the
stove.
2. Open the secondary air inlet by pushing it in fully.
3. Cover with crumpled pieces of paper.
4. Lay 10-12 pieces of kindling on top of the paper towards the back of the firebox.
5. Ignite and close the firedoor.
6. Under no circumstances should any flammable liquid i.e. petrol, paraffin etc., be
used to light the fire.
7. When the kindling is well alight open the firedoor and add more kindling of a larger size
to sustain the fire. Close the firedoor.
8. When a hot fuel bed is established add the normal fuel.
9. When well lighted, adjust the thermostat to give the required heat output.
10. To shut the fire down, do not add fuel, make sure that the firedoor is properly closed and
that the primary and secondary air controls are all in the closed position. Cutting off the
air supply will reduce the heat output.
11. Following a prolonged shutdown of the appliance perhaps after the summer break,
ensure the flueway is free from obstruction prior to re-lighting.
Re-fuelling-Open the firedoor and reload, close the firedoor.
Fig.19
Before lighting the stove he k with the installer that the installation work and
ommissioning he ks des ribed in the installation instru tions have been arried
out orre tly and that the himney has been swept lean, is sound and free from any
obstru tions. As part of the stove’s ommissioning and handover the installer
should have demonstrated how to operate orre tly.
13

AIR CONTROLS
The air control is very important for the performance
and correct use of the stove. There are two air con-
trols on the Lismore non boiler stove, a primary air
control and a secondary air control.
Primary air ontrol
The primary air control lever is located on the right
hand side of the stove, raise the lever to shut off the
air supply and lower it to open the air supply.
Se ondary air ontrol
The secondary air control is located under the base
to the right hand side of the front. See Fig.20.
Push to open the secondary air supply and pull to
close. This knob will become hot when the stove is
in operation and should be adjusted with the use of
the tool or glove provided.
When burning wood the primary air control maybe
closed or slightly open, the burn rate of the wood
can then be controlled using the secondary air
control. See Fig.20.
When burning coal the secondary air control can be
left slightly open to allow window wash air assist in
keeping the glass clean. The burn rate of the coal
should be controlled using the primary air control.
See Fig.20.
When burning anthracite or smokeless fuel the
secondary air control must be closed and the burn
rate can be controlled using the primary air control.
It is permissible to have both air controls fully open
when lighting the stove so that the fire can become
established and the necessary heat gets into the
chimney to provide a flue draught. When the fire is
established one or other of the controls should be
shut down as outlined above failure to do so may
lead to excessive temperatures in the stove. See
Fig.20.
O EN When burning coal, timber or peat.
CLOSE When burning anthracite and
smokeless fuels.
O ERATING INSTRUCTIONS
RECOMMENDED FUELS
All fuels should be stored under cover and kept
as dry as possible prior to use.
This appliance has been tested using seasoned
wood logs and manufactured briquetted smokeless
fuel (Ancit) for closed appliances, sized between
20g and 140g. Other fuels are commercially avail-
able and may give similar results. Wood logs up to
340mm long are suitable. All fuels should be stored
under cover and kept as dry as possible prior to use.
Do not use fuels with a Petro-coke ingredient as this
may cause the grate to overheat, causing damage.
Reduced outputs will result when fuels of lower
calorific values are used. Never use gasoline or
gasoline type lantern fuel, kerosene, charcoal lighter
fluid or similar liquids to start or freshen up a fire in
this heater. eep all such liquid well away from the
heater at all times. Operate the stove only with the
fuelling door closed except for re-fuelling.
This stove has obtained HETAS Ltd approval for
burning natural and manufactured smokeless fuels
only as detailed in recommended fuels below.
HETAS Approval does not cover the use of other
fuels either alone or mixed with the recommended
fuels listed, nor does it cover instructions for the use
of other fuels.
WARNING:
Properly installed, vented, operated and main-
tained this stove will not emit fumes into the
dwelling. Occasional fumes from de-ashing and
re-fuelling may occur. However, persistent fume
emission is potentially dangerous and must not be
tolerated. If fume emission does persist, then the
following immediate action should be taken -
(a) Open doors and windows to ventilate room and
then leave the premises.
(b) Let the fire out.
(c) Check for flue or chimney blockage and clean
if required.
(d) Do not attempt to relight the fire until the cause
of the fume emission has been identified and
corrected. If necessary seek expert advice.
The most common cause of fume emission is flue-
way or chimney blockage. For your own safety
these must be kept clean at all times.
14

Fig.20
DE-ASHING
When ash build-up becomes excessive in the fire
chamber shake the firebars by pushing and pulling
the riddling rod repeatedly. The riddling rod is locat-
ed under the base at the left side of the stove.
Fig.21
mend that you remove ashes after you have riddled
the fire when the stove is thoroughly cooled.
Ashes should be placed in a metal or other non-
combustible container with a tight fitting lid. The
closed container of ashes should be placed on a
non-combustible material, pending final disposal. If
ashes are buried in soil, or otherwise dumped they
should be retained in the closed container until they
are thoroughly cooled. See Fig.22.
Fig.22
TO CLEAN CHIMNEY BACK OUTLET
To gain access to clean the chimney some compo-
nents need to be removed.
First the fire fence should be removed, then the front
brick on the right hand side which was underneath
the fire fence can be removed by catching it close to
the centre of the stove and pulling it into the centre
of the stove in a slightly upwards motion.
Then the side brick on the front right hand side can
be removed by lifting it and then pulling it out on the
bottom. See Fig.23 & 24.
DIS OSAL OF ASHES
Your stove is provided with a stainless steel ashpan.
This ashpan should be emptied every day.
If ashes are allowed to build to grate level you could
damage the firebars by overheating. We recom-
15
Fig.23

Fig.24
Flue Exit
Removable
Baffle
Grate Bars
Ashpan
CHANGING GRATE ORIENTATION
For best combustion of coal it is best to burn it on an
open grate as the ash needs to be frequently
removed to avoid a build up of ash on the grate.
For best combustion of wood it is best to use a flat
grate so that it can build up a bed of ash as it burns.
The grate on the Lismore Stove can be changed
from a coal setting to wood burning setting.
The product is supplied factory set for coal burning,
this should not be changed if a mixture of fuels are
being used i.e. (coal, wood, peat, anthracite). If
burning wood only, change the grate setting by
opening the ash door and remove the ash pan. This
Fig.25
Wood Setting
Riddling Rod
Coal Setting
Riddling Rod
Fig.26
16
should reveal a hex head bold on the left hand side
which should be removed, with the bolt removed the
riddling bar can now be moved to the wood burning
position.
The hex head bolt should now be re-inserted in the
alternative position which will lock the grate in the
wood burning position. See Fig.27
See Fig, 25 & 26 showing the position of the grate
for wood burning and coal burning, note the position
of the riddling rod also.
WARNING - DO NOT CHANGE GRATE
OSITION WHEN STOVE IS HOT.
The back brick on the same side can be slid forward
and removed in a similar fashion. Next the main baf-
fle can be slid approx 10mm to the right hand side,
then lift it clear of the supports at the rear, drop the
baffle down into the stove to allow it be removed
carefully through the front without touching enam-
elled parts.
The secondary baffle can then be removed by lifting
it off the legs off the ledge on which they rest and
dropping it into the stove,
This will leave access to clean the chimney, When
the chimney has been cleaned the components
must be refitted in the reverse order.

FIRE SAFETY
To provide reasonable fire safety, the following
should be given serious consideration.
1. Do not over fire the stove.
2. Over-firing will also damage painted or enamel
finish.
3. Install a smoke detector in the room.
4. A conveniently located class A fire extinguisher to
contend with small fires resulting from burning
embers.
5. A practical evacuation plan.
6. A plan to deal with a chimney fire as follows:-
(a) Notify the fire department.
(b) Prepare occupants for immediate evacua-
tion.
(c) Close all openings into the stove.
(d) While awaiting the fire department watch for
ignition to adjacent combustibles from over-
heated flue pipe or from embers or sparks
from the chimney.
VITREOUS ENAMEL CLEANING
General cleaning must be carried out when the
stove is cool.
If this stove is finished in a high gloss vitreous
enamel, to keep the enamel in the best condition
observe the following tips:
1. Wipe over daily with a soapy damp cloth,
followed by a polish with a clean dry duster.
2. For stubborn deposits a soap impregnated
pad can be carefully used on the vitreous
enamel.
3. Use only products recommended by the
Vitreous Enamel Association, these products
carry the Vitramel label.
4. DO NOT USE ABRASIVE ADS OR OVEN
CLEANSERS CONTAINING CITRIC ACID
ON ENAMELLED SURFACES. ENSURE
THAT THE CLEANSER MANUFACTUR
ERS INSTRUCTIONS ARE ADHERED TO.
GLASS CLEANING
The glass will self clean when there is sufficient heat
generated by the burning fuel. If a build-up of cre-
osote occurs on the glass it may be due to draft con-
ditions, poor quality fuel or very low burning for a
long time. It is best to clean the glass when it is
thoroughly cooled.
GLASS RE LACEMENT
(a) Open the firedoor fully.
(b) Remove the four corner screws and clips and
carefully remove the broken glass.
(c) Clean the glass recess in the door.
(d) Replace the sealing rope in the door if
necessary
(e) Tighten screws.
(f) Replace glass only with ceramic glass 5mm
thick. (See Fig.28).
SUMMER SHUTDOWN
For summer shutdown of the stove, ensure all ashes
have been cleaned from the ash compartment and
that the air control is open, to avoid condensation in
the stove firebox and possible corrosion during this
shutdown period.
Fig.28
17
Fig.27
Hex Bolt

1. FLUE SPIGOT - B00116AZZ
2. STOVE LEG - B00595AZZ
3. BASE - B00610AZZ
4. FRONT - B00611AZZ
5. RIGHT HAND SIDE - B00612AZZ
6. LEFT HAND SIDE - B00613AZZ
7. HOB - B00630AZZ
8. FIREDOOR - B00615AZZ
9. ASH DOOR - B00616AZZ
10. DOOR GLASS CLIP - F00003AXX
11. RIDDLING LIN - F01068AXX
12. LIN BRACE - F01069AXX
13. AIR CHANNEL COVER - F01071AXX
14. DAMPER - F01073AXX
15. BRAC ET - F01074AXX
16. ASHPAN BODY - F01075AXX
17. ASHPAN COVER - F01082AXX
18. PRIMARY AIR CONTROL SHUTTER - F01098AXX
19. OSA BOX COVER - F01101AXX
20. LISMORE NB SHELL - F01102AXX
21. BAC BRIC - H00214AXX
22. SIDE BRIC LH FRONT - H00215AXX
23. LH FRONT BRIC - H00216AXX
24. RH FRONT BRIC - H00217AXX
25. SIDE BRIC RH FRONT - H00218AXX
26. HEAT EXCHANGER - Q00765AXX
27. GLASS - T00101AXX
28. PULL ROD NOB - U00001AXX
29. NOB SECONDARY AIR DAMPER - U00018AXX
30. Door Handle - U00191AXX
31. HINGE - U00193AXX
32. SPACER TO DOOR HANDLE - V00035AXX
33. BADGE - V00912AXX
34. DOOR CATCH - V00985AXX
35. DAMPER ROD - V00988AXX
36. RIDDLING ROD - V00989AXX
37. FRONT STRIP - V00990AXX
38. SPACER - V00991AXX
39. HINGE PIN (CAM ACTION) - V00997AXX
40. DAMPER CONTROL ROD - V01005AXX
41. DAMPER LEVER - V01006AXX
42. RIDDLING BAR - Z00047AXX
43. FLUE CLEANING DOOR - Z00048AXX
44. FIRE FENCE - Z00059AXX
45. BAC CASTING - Z00055AXX
46. ROOF PROTECTION PLATE - Z00056AXX
47. ROOF PROTECTION PLATE REAR - Z00057AXX
48. BLANKING LATE - B00631AZZ
18
EX LODED VIEW

INSTALLATION CHECK LIST
Flue System
1. Minimum Flue Height of 4.6 metres (15 feet).
2. Appliance should be connected to a minimum of 1.8 metres (6 feet) of 150mm (6”)
flue pipe with a horizontal run not exceeding 150mm (6”).
3. Appliance should be connected to a chimney of less than 200mm (8”) in diameter
(otherwise the chimney must be lined with a 6” flue liner).
4. The chimney venting position must be above the main ridge of the roof or adjacent
outside obstructions.
5. The chimney serving this appliance should not serve any other appliance.
6. Access should be provided to the chimney serving the appliance to allow for cleaning.
Location
7. Clearance to combustible materials must be adhered to as described in the Clearance
to Combustible section.
8. The stove must be installed on a floor protector that covers the area under the stove
and extends 18” to the front & 8” to the sides and back.
Ventilation & Combustion Air Requirements
9. The room in which the appliance is located should have an air vent of adequate
size to support correct combustion (see Ventilation & Combustion Air Requirement
Section for specific details).
Tick
Manufactured by
Waterford Stanley Ltd.,
Unit 401-403, IDA Industrial Estate, Cork
Road, Waterford, Ireland.
Tel: [phone] Fax [phone]
19 D 130905N00562AXX