StarTech.com SAT2IDEADP User manual

Manual Revision: 08/28/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SAT2IDEADP
SATA to 2.5in or 3.5in IDE Hard Drive
Adapter for HDD Docks
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................3
3.5in Hard Drive Setup ............................................................................................................................ 3
2.5in Hard Drive Setup ............................................................................................................................ 5
Specications..........................................................................................6
Technical Support ..................................................................................7
Warranty Information............................................................................7

Instruction Manual
1
Introduction
The SAT2IDEADP SATA to IDE hard drive adapter enables you to use your 2.5-inch/3.5-
inch IDE-based (PATA) hard drives in most StarTech.com SATA-based HDD docking
stations and drive duplicators. The SATA-IDE adapter features all-metal construction
that ensures maximum durability, and is fully compatible with IDE hard drives up to
ATA-133 (133MBps).
The unique mounting style of the SATA/IDE adapter enables it to be easily mounted
to an IDE/ATA hard drive, and inserted into a SATA hard drive dock bay, for quick and
easy retrieval of data from older HDDs. The adapter can also be used to install IDE hard
drives into SATA-only desktop computers, or any other scenario that requires an IDE
hard drive to be connected through Serial ATA.
Packaging Contents
• 1x SATA to IDE adapter
• 1x 40-pin IDE cable
• 1x 40-pin to 44-pin IDE cable with power
• 1x SP4 to LP4 Power cable
• 1x Package of mounting screws
• 1x Instruction Manual
System Requirements
• 2.5in 44-pin IDE hard drive or 3.5in 40-pin IDE hard drive

Instruction Manual
2

Instruction Manual
3
3.5” Hard Drive
Mounting Points
2.5” Hard Drive
Mounting Points
Installation
3.5in Hard Drive Setup
1. If connecting a 3.5in (40-pin) IDE hard drive, connect the 40-pin IDE ribbon cable to
the 40-pin connector on the inside of the SAT2IDEADP.
2. Connect the large 4-pin LP4 power cable to the small 4-pin SP4 oppy power
connector on the inside of the SAT2IDEADP.

Instruction Manual
4
3. Connect the ribbon cable and power cable to the connectors on the IDE hard drive.
4. Place the IDE drive onto the back plate of the SAT2IDEADP adapter and fold/tuck the
cables into the opening of the adapter. Slide the IDE drive towards the connectors
until the mounting holes on the bottom of the drive line up with the mounting
points on the back plate of the adapter. The edge of the IDE drive should be sitting
almost ush with the edge of the adapter’s opening.
5. Use the provided screws to fasten the drive to the back plate of the adapter. Small
screws provided for 2.5”drives and larger screws for 3.5” drives.
Mounting Screws
Tuck in Cables

Instruction Manual
5
2.5in Hard Drive Setup
1. If connecting a 2.5in (44-pin) IDE hard drive, connect the 40-pin to 44-pin IDE ribbon
cable to the 40-pin connector on the inside of the SAT2IDEADP.
2. Connect the small 4-pin SP4 oppy power cable from the ribbon cable into the SP4
connector on the inside of the SAT2IDEADP.
3. Connect the IDE hard drive to the 44-pin connector on the ribbon cable.
4. Place the IDE drive onto the back plate of the SAT2IDEADP adapter and fold/tuck the
cables into the opening of the adapter. Slide the IDE drive towards the connectors
until the mounting holes on the bottom of the drive line up with the mounting
points on the back plate of the adapter.
5. Use the provided screws to fasten the drive to the back plate of the adapter. Small
screws provided for 2.5”drives and larger screws for 3.5” drives.

Instruction Manual
6
Specications
Host Interface SATA revision 1.0
Connectors 1 x 40-pin IDE male
1 x SP4 Power male
Compatible Hard Drives 2.5in and 3.5in PATA (IDE) 66/100/133
hard drive
LBA Support 48-bit
Enclosure Material Metal
Operating Temperature 5°C ~ 80°C (41°F ~ 176°F)
Storage Temperature -40°C ~ 70°C
(-40°F ~ 158°F)
Humidity 8% ~ 90% RH
Dimensions (LxWxH) 101.0mm x 78.0mm x 26.0mm
Weight 104g

Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.