StarTech.com POEKIT100 User manual

Manual Revision: 02/09/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
POEKIT100
POESPLT100
POEINJ100
10/100 Power over Ethernet Kit
– 48V Injector and 5V/ 12V Splitter
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Side View - POEINJ100............................................................................................................................. 2
Side View - POESPLT100.......................................................................................................................... 2
Installation ..............................................................................................3
POEINJ100.................................................................................................................................................... 3
POESPLT100 ................................................................................................................................................ 3
Specications - POEINJ100...................................................................4
Specications - POESPLT100 ................................................................5
Technical Support ..................................................................................6
Warranty Information............................................................................6

Instruction Manual
1
Introduction
The POEINJ100 10/100 Mbps Power over Ethernet (PoE) injector converts standard
90V ~ 260V AC power into low-voltage DC power that can run over existing Cat5 or
higher network cable to power IEEE 802.3af/at compliant network devices, or the
POESPLT100 PoE Splitter.
The POESPLT100 splitter device separates the data and power connections received
from the Injector device and oers a selectable 5V, 7.5V, 9V or 12V DC output switch
allowing you to customize the power output to suit your requirements. Taking
advantage of PoE technology lets you expand your technology infrastructure without
the hassle or expense of running new electrical wiring.
Packaging Contents
POEKIT100 POEINJ100 POESPLT100
1 x PoE Injector 1 x PoE Injector 1 x PoE Splitter
1 x PoE Splitter 1 x Power Adapter 1 x Power Output Cable
1 x Power Output Cable 1 x Instruction Manual 1 x Instruction Manual
1 x Power Adapter
1 x Instruction Manual
System Requirements
• RJ45 terminated Cat5 or higher Ethernet cabling
• 10/100 Mbps compatible Ethernet network
• Available AC power outlet for the POEINJ100 unit

Instruction Manual
2
Side View - POEINJ100
Side View - POESPLT100

Instruction Manual
3
Installation
PoE Injector (POEINJ100)
The injector should be on the side that does not require Power over Ethernet (source).
1. Connect the RJ45 Ethernet cable from the network device (i.e. computer, router,
switch, etc) that does not require power over Ethernet to the“Data (In)” RJ45
connector on the input side of the PoE Injector unit.
2. Connect the included power adapter to the PoE Injector unit.
3. Connect an RJ45 terminated Cat5 or better Ethernet cable to the “Power + Data
(Out)”connector on the output side of the PoE Injector unit. The other end of the
cable will either connect directly to a PoE compliant device, or to a PoE Splitter in
order to separate data and power again.
PoE Splitter (POESPLT100)
1. Connect the RJ45 Ethernet cable from the PoE injector unit (or other PoE Power
Source device) to the “Data + Power (In)” RJ45 connector on the input side of the
PoE Splitter unit.
2. Set the slide switch along the side of the PoE Splitter to the desired DC voltage
output (5V, 7.5V, 9V, or 12V).
3. Connect an RJ45 terminated Cat5 or better Ethernet cable from the “Data (Out)”
connector on the output side of the PoE Splitter to the network device (i.e. computer,
router, switch, etc).
4. Connect the included Power Output Cable from the “Output Power” connector on
the output side of the PoE Splitter to the DC power connector on the device you
wish to have powered.
NOTE: The included power cable has a type N sized tip. If the device to be powered
is not compatible with this tip size, a dierent cable will need to be sourced.

Instruction Manual
4
Specications - POEINJ100
Compliant Standards
IEEE 802.3af
IEEE 802.3at
IEEE 802.3
IEEE 802.3u
Connectors 2 x RJ45 Ethernet female
1 x DC Power Type N
LEDs 2 x RJ45 Link
PoE Output 48V DC, 30W
Link Speeds 10/100 Mbps
Maximum Cable Length 100m / 330ft
Power Adapter 48V DC, 880mA, Type N Plug
Operating Temperature 0°C ~ 40°C (32°F ~ 104°F)
Storage Temperature -20°C ~ 85°C (-4°F ~ 185°F)
Humidity 10% ~ 90% RH
Dimension (LxWxH) 102.0mm x 75.0mm x 23.0mm
Weight 490g

Instruction Manual
5
Specications - POESPLT100
Compliant Standards
IEEE 802.3af
IEEE 802.3at
IEEE 802.3
IEEE 802.3u
Connectors 2 x RJ45 Ethernet female
1 x DC Power Type N
LEDs 1 x RJ45 Link
PoE Input 48V DC, 30W
Power Output 5V / 7.5V / 9V / 12V DC,
up to 19.2W peak
Link Speeds 10/100 Mbps
Operating Temperature 0°C ~ 45°C (32°F ~ 113°F)
Storage Temperature -20°C ~ 90°C (-4°F ~ 194°F)
Humidity 10% ~ 90% RH
Dimension (LxWxH) 102.0mm x 75.0mm x 23.0mm
Weight 240 g

Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.