StarTech.com SVID2USB2NS User manual

Manual Revision: 05/08/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
*actual product may vary from photos
SVID2USB2NS
Video Capture Cable with
Composite and S-Video Input

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Installation ..............................................................................................2
Driver Installation...................................................................................................................................... 2
Application Installation........................................................................................................................... 3
Hardware Installation .............................................................................................................................. 4
Operation..................................................................................................................................................... 4
Option......................................................................................................5
General.......................................................................................................................................................... 5
Encoder Property ...................................................................................................................................... 5
Troubleshooting.....................................................................................7
Specications..........................................................................................9
Technical Support ..................................................................................10
Warranty Information............................................................................10

Instruction Manual
1
Introduction
The SVID2USB2NS USB 2.0 S-Video and Composite video Capture Cable lets you
connect devices that output S-Video or Composite video to a computer, through an
available USB 2.0 port.
The perfect solution for bridging a computer and an S-Video or Composite video
source, the capture cable oers real time MPEG 1, MPEG 2 and MPEG 4 recording. Small
enough to t in the palm of your hand, the Capture Cable is a great solution for mobile
applications and integrates seamlessly with laptop and desktop computers.
If you require audio with your video capture please see StarTech.com’s S-Video to USB
2.0 Video Capture Cable(SVID2USB).
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Packaging Contents
• 1 x SVID2USB2NS video capture cable
• 1 x User Manual
• 1 x Driver CD
System Requirements
• USB 2.0 equipped computer
• Pentium 4 - 1GHz or above or equivalent AMD processor
• 128MB of RAM
• Microsoft Windows® 2000 SP4, XP SP2 or above, or Vista

Instruction Manual
2
Installation
USB 2.0 connector: Connect to USB 2.0 port of your computer
S-Video input: S-Video input from external A/V device (e.g. VCR)
Composite video input: Composite video input from external A/V Device (e.g. VCR)
* If you want capture audio, please connect audio directly to Line-in of your Sound card.
USB 2. 0
connector
Composite
input
S-Video
input
Driver Installation
Note: Do not connect SVID2USB2NS adapter to computer USB port before driver
installation!
Note: Please make sure your computer has USB2.0 port correctly installed and
functioning !! ( Please update your Windows® XP to at least SP2, or Windows® 2000 to
SP4, and updating the USB 2.0 host controller drivers before installation to make sure
the computer’s USB 2.0 is functioning correctly)
1. Please insert “Multimedia Installation Kit” CD-ROM into your CDROM drive; AutoRun
will play; (if AutoRun does not run, please go to “My Computer” and double click the
CD-ROM drive).
2. From the menu, please select the “GrabBeeX-light” product.
3. Please select “Device Driver” on the next screen.
* Note: In Vista, windows will get a pop up dialogue box. Choose “Allow” to continue
the installation.
4. Click “Next”.
5. Complete Setup Wizard.
6. Click “Finish”, then please restart the computer.

Instruction Manual
3
Application Installation
1. Please insert “Multimedia Installation Kit” CD-ROM into your CDROM drive; AutoRun
will play; (if AutoRun does not run, please go to “My Computer” and double click the
CD-ROM drive).
2. From the menu, please select the “GrabBeeX-light” product.
3. Please select “Application Software” on the next screen.
4. Please select “GrabBee”.
5. Welcome to the InstallShield wizard; Click“Next”.
6. Select the language you will use for GrabBee; then click “Set”.
7. Choose the destination location; Click “Next”.
Note: Under Windows Vista, steps 8 to 17 will automatically be skipped. Please do
not worry as this is normal.
8. Install Windows Media Format 9 Series Runtime Setup;
9. Click “Yes”.
10. License agreement; Click “Yes”.
11. Finished Windows Media Format 9 Series Runtime installation;
12. Click “OK”
13. License for Windows Media Tools Setup; Click “Yes”.
14. Windows Media Tools Setup; Click “Next”.
15. Create folder; Click “Yes”.
16. Installation Options; Click “Next”.
17. Installation Directory; Click “Finish”.
18. Setup Complete; Click “OK”.
19. InstallShield Wizard Complete; Click “Finish” then please restart the computer.

Instruction Manual
4
After the AP software is installed, three icons will now be shown on screen:
GrabBee : GrabBee software main program
Record Files : Click to see your record  les
Snapshot : Click to see your capture still image  les
Hardware Installation
After the computer restarts, please plug the SVID2USB2NS device into the computer’s
USB 2.0 port; System will now detect the new device and install it automatically.
Please check whether the SVID2USB2NS driver was installed successfully in your computer.
Operation
Starting : Please click the “GrabBee” icon. After starting the application, you can see
video window as below.
Video Window: Please move mouse cursor into Video window and right click, function
menu will appear as below.
Resolution : There are 4 resolution video preview you can select,
NTSC mode : 352x240, 640x480, 720x480, Full screen
PAL mode : 352x288, 640x480, 720x576, Full screen

Instruction Manual
5
Option
General
• Lists your hard disk space information.
• Snapshot default storage path : The location to saved captured image  les.
• Clip default storage path : Location to saved recorded video  les.
• Video Format : Choose your correct video format input.
• Set Recording Time : Sets Recording Time length.
Encoder Property
• Video Setting: Recording  le type format AVI, MPEG-1, MPEG-2, VCD, SVCD, DVD,
WMV, *MP4 selection (if you want DVD burning, please choose DVD mode)
• Prole: Video Size, Frame Rate, Video Quality, Video Bitrate setting; Information
column will display your setting
Note: File format‘MP4’will not appear as a selectable option under Windows Vista.
Schedule Record : Set One-time schedule here. Input your Start and Stop time, Date,
Video Source, and File Name. Click‘Add’ after input then ‘OK.’
Video Input : Switch between Composite or S-Video input.
Slide Bar : Move to any video position during playback.
Color Setting : Brightness/Contrast/Hue/Saturation adjustment.
Mute : Volume On/O
Pause : Pauses the playback  le
Record : Click this button to start recording a video. After you click “Stop“ button,
a table will be shown, which asks you to rename or save the  le; default  le name
format is “Mddhhmmss”.
M : Month (Jan->1, Feb->2….Oct->O, Nov->N, Dec->D)
dd : Date, hh : Hour, mm : Minute, ss : Second
Stop : Stop Recording and Playback;
Playback : Play the recorded le
SnapShot : Image capture resolution is the same as Preview mode’s
Resolution; click SnapShot and a table shows as below.

Instruction Manual
6
You can “Save”, “Save All”, “Delete”, “Delete All” image  les,  le name’s format is
“Mddhhmmssn”.
M : Month (Jan->1, Feb->2….Oct->O, Nov->N, Dec->D)
dd : Date; hh : Hour; mm : Minute; ss : Second
n : Number
Album: The Album will show all capture  les including image and video. Please click
“Clips” or “Images”to  nd all listed; you can nd each  le’s information, or preview the
recording video in this window.
Full Screen mode : Double click inside your video window to switch back and forth
between full screen and previous screen size.

Instruction Manual
7
Troubleshooting
Q1 : Why can’t my system detect the SVID2USB2NS?
A1 : Check that you’ve enabled USB 2.0 in the motherboard BIOS setup.
Please make sure that your system has the latest USB 2.0 host driver.
For Windows® XP, please upgrade to Service Pack 2 or above.
For Windows® 2000, please upgrade to Service Pack 3 or above.
Q2 : Why can’t I see video display?
A2 : Perhaps the video system setup is incorrect; please check your hardware
connection and choose the correct Video Format from the Options menu
Please make sure that your system has the latest USB 2.0 host driver.
For Win XP, please upgrade to Service Pack 2 or above.
For Win 2000, please upgrade to Service Pack 3 or above.
Q3 : Why is the resolution always in 320x240 under preview mode?
A3 : It’s because you plugged the SVID2USB2NS in a USB 1.1 port, or perhaps even
though your USB port is 2.0, it may not have upgraded to USB 2.0 drivers. Please make
sure your USB port is USB 2.0, and have already upgraded the USB 2.0 host driver
available from Microsoft’s Website.
Q4 : Why does the system show “High Speed device plug into Full speed USB port…”
A4 : Please make sure your system supports USB 2.0 hardware.
Please make sure that you’ve installed USB 2.0 Host drivers.
Q5 : Why do I get unstable video during preview and recording?
A5 : If you are using Ultra DMA hard disk, please updated the latest driver of IDE ATA/
ATAPI controller. Certain motherboards’bundled driver are not of the latest version, we
suggest that you use Windows’ own system bundled driver.
Q6 : Why can’t I hear anything under preview mode?
A6: The audio needs to go through sound card’s Line-in, please check your sound card
setting.