StarTech.com SAT2510BU2E User manual

Serial ATA Hard Drive
Enclosure
2.5” eSATA/USB External Hard
Drive Enclosure for Serial ATA
Hard Drives
SAT2510U2E
SAT2510BU2E
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 2
Hardware Installation...................................................................3
Driver Installation.........................................................................4
Verifying Installation.....................................................................5
How to Use ...................................................................... 5
Specifications.................................................................. 7
Technical Support........................................................... 8
Warranty Information...................................................... 8

1
Introduction
This External Hard Drive Enclosure transforms most 2.5” SATA hard
drives into a cost-effective portable storage solution . The 2.5” SATA
hard drive enclosure connects to a host computer using USB 2.0
or eSATA with support for data transfer rates of up to 3Gbps (using
eSATA) or 480Mbps (through USB 2.0).
Packaging Contents
1 x SAT2510U2E or SAT2510BU2E enclosure•
1 x eSATA cable•
1 x USB cable•
1 x Driver CD•
1 x Instruction Manual•
System Requirements
Available USB 2.0 or eSATA port on computer system•
Microsoft Windows• ®2000/XP/Server 2003/Vista (32/64-bit),
Mac OS®X, Linux®

2
Installation
WARNING: Hard drives require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data
may result. Always handle your hard drive and storage device with
caution.
WARNING: Hard drives, like all computer equipment can also be
severely damaged by static electricity. Be sure that you are properly
grounded before opening your computer case or touching any
components. StarTech.com recommends that you wear an anti-static
strap when installing any computer equipment. If an antistatic strap
is unavailable, discharge yourself of any static electricity build-up by
touching a large grounded metal surface (such as the computer case)
for several seconds.
Power
connector
eSATA USB Power/Activity
LED

3
Hardware Installation
Remove the screws from the enclosure, and remove the rear panel1.
cover. Pull the front panel out of the enclosure:
Attach the 2.5” SATA hard drive to the connector provided:2.
Insert the front panel (with drive attached) into the rear panel3.
(enclosure).

4
Fasten the front panel (with drive attached) to the rear panel4.
(enclosure), using the screws removed in step #1.
To connect the hard drive enclosure to a host computer using USB,5.
simply insert the included USB cable into the USB type Mini B slot
provided by the enclosure, and the remaining end into an available
USB type A slot on the host computer.
To connect the hard drive enclosure to a host computer using6.
eSATA, simply plug the included eSATA cable from the enclosure to
the host computer. To provide power to the enclosure, connect the
USB to DC cable (provided) to an available USB port on the host
computer, and insert the remaining end into the power port located
on the hard drive enclosure.
Driver Installation
Windows 2000/XP/Server 2003/Vista, Mac OS X, Linux
No driver installation is required for these operating systems, as this
enclosure is natively supported, so the drivers are already installed.

5
Verifying Installation
Windows 2000/XP/Server 2003/Vista
From the main desktop, right-click on “My Computer” (“Computer” in
Vista), then select Manage. In the new Computer Management window,
select Device Manager from the left window panel.
Double-click on the “Disk Drives” option. A new disk drive should be
listed under this category. It will typically contain the make/model of
the hard drive you have installed in the enclosure.
How to Use
Windows 2000/XP/Server 2003/Vista
Right-click on My Computer, and select Manage.1.
Select Disk Management, in the left pane. In the right pane, you2.
should notice the new hard drive:

6
Right-click on the Unallocated block, and select New Partition.3.
This will launch the New Partition Wizard. Please follow the4.
instruction provided by the Wizard, to partition the drive for use.
Once the partition has been created, the drive installed within the5.
hard drive enclosure will be recognized as a New Volume in Disk
Management, as well as in My Computer:

7
Specications
Bus Interface USB 2.0
SATA 3Gb/s
External Connectors
1 x USB mini B
1 x eSATA port
1 x DC power connector
Chipset JMircon JM20316
LEDs 1 x Power/Activity
Maximum Data Transfer Rate USB: 480 Mb/s
eSATA: 3 Gb/s
Hard Drive Compatibility 2.5” SATA 1.5 and 3 Gb/s hard
drives, 9.5mm height
Dimensions 133.0 mm x 72.0 mm x 13.0 mm
Weight 90 g
Compatible Operating
Systems
Windows 2000/XP/Server 2003/
Vista, Mac OS X, Linux