StarTech.com PEX1000SFP2 User manual

Manual Revision: 08/03/2018
User Manual
For the latest information and specications visit
www.startech.com/PEX1000SFP2
PCI Express Gigabit Ethernet Fiber Network
Card with Open SFP Slot
Actual product may vary from photos
SKU#: PEX1000SFP2

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
For the State of California
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に
従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
Warning Statements
Make sure to assemble this product according to the instructions. Failure to do
so might result in personal injury or property damage.
Never use this product if parts are missing or damaged.

4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements........................................................................1
Safety Statements..................................................................................2
Warning Statements ..............................................................................3
Product Diagram ....................................................................................5
Card................................................................................................................................................................ 5
Jumper.......................................................................................................................................................... 5
Product Information .............................................................................6
Package Contents ..................................................................................................................................... 6
System Requirements.............................................................................................................................. 6
Installation ..............................................................................................7
Hardware Installation .............................................................................................................................. 7
Driver Installation...................................................................................................................................... 8
Verifying Installation................................................................................................................................ 11
Software Utility ......................................................................................14
Connecting to a Network......................................................................14
Network Conguration ........................................................................................................................... 14
Card to Card Direct Conguration.......................................................16
LEDs..........................................................................................................17
Specications..........................................................................................17

5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Card
Jumper
Link LED
SFP
Slot Activity
LED
JP2 Jumper

6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
• Port PCI Express Gigabit SFP Network Card x 1
• Low Prole Bracket x 1
• Driver CD x 1
• User Manual x 1
System Requirements
• PCI Express enabled computer with an available PCI Express
slot
• Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP
(32/64), Windows Server® 2012, 2008 R2, 2003, Mac OS
10.5 and up (Tested up to 10.9), Linux 2.4.x, 2.6.x and 3.5.0,
Microsoft Hyper-V®

7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installation
Hardware Installation
WARNING! PCI Express cards, like all computer equipment,
can be severely damaged by static electricity. Be sure that
you are properly grounded before opening your computer
case or touching your PCI Express card. StarTech.com recom-
mends that you wear an anti-static strap when installing any
computer component. If an anti-static strap is unavailable,
discharge yourself of any static electricity build-up by touch-
ing a large grounded metal surface (such as the computer
case) for several seconds. Also be careful to handle the PCI
Express card by its edges and not the gold connectors.
1. Turn your computer o and any peripherals connected to
the computer (i.e. Printers, external hard drives, etc.). Unplug
the power cable from the rear of the power supply on the
back of the computer and disconnect all peripheral devices.
2. Remove the cover from the computer case. See
documentation for your computer system for details.
3. Locate an open PCI Express slot and remove the metal
cover plate on the rear of the computer case (Refer to
documentation for your computer system for details).
Note: This card will work in PCI Express slots of additional
lanes (i.e.x4, x8, or x16 slots).
4. Gently insert the card into the open PCI Express slot and
fasten the bracket to the rear of the case.

8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Note: If installing the card into a small form factor/low
prole system, replacing the pre-installed full prole bracket
with the included low prole installation bracket may be
necessary.
5. Place the cover back onto the computer case.
6. Insert the power cable into the socket on the power supply
and reconnect all other connectors removed in Step 1.
Driver Installation
Windows
Note: The card may auto-install using native drivers, how-
ever it is recommended to use the procedure below to update
to the latest driver version.
1. Upon starting Windows, if the Found New Hardware dialog
appears on the screen, cancel/close the window and insert
the included Driver CD into the computer’s CD/DVD drive.

9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. If AutoPlay is enabled, select the “Open folder to view les”
option when the dialog appears.
Autoplay screen
3. Open the “PEX1000MMSC2_SFP2_Driver” folder, and run the
“Setup.exe” application within the appropriate Operating
System folder for the system you are using.