Stealth Cam QV Series User manual

Page 1
QV Series
Instruction Manual
R0

Page 2
To ensure the product is being utilized to its full potential, we recommend checking
our website for new product updates. If your camera is having an issue, please check
our website to determine you are using the latest rmware or software version.
Notice
TECHNICAL SUPPORT
EMAIL:
[email protected]
Please allow 48 hours for email
response.
GSM, LLC
P.O. Box 535189
Grand Prairie, TX 75053-9504
CUSTOMER SERVICE
CONTACT & HOURS
Toll Free: 877-269-8490
CALL CENTER HOURS
Mon – Fri / 8 AM – 5 PM (CST)
WEBSITE
www.stealthcam.com
Contact Us
QS20NGK

Page 3
Table of Contents
About Your Camera 4
Quick Setup Guide 5
Camera Overview 6
Camera Setup 8
Camera Conguration 9
Viewing and Deleting Images 12
Frequently Asked Questions 13
Camera Care 14
FCC COMPLIANCE 15
Limited Warranty Information 16

Page 4
About Your Camera
Water Resistant Design
Your camera is safe against the elements with a sturdy waterproof housing.
Quick Set Options
Set up in seconds with pre-programmed options.
Burst Rapid-Fire Mode
Rapid-re Burst Mode, multiple exposures per triggering.
No Glow IR LEDs
Perfectly illuminate your nighttime photos with 24 IR LED lights.
Expandable Storage Space
Expand your storage space with an SC memory card up to 32 GB.
Energy E󰀩cient Design
Completely re-energized to optimize energy e󰀩ciency.

Page 5
Quick Setup Guide
Insert Batteries and SD Card
Install 8 AA batteries and a class 10 SD card into camera.
Mount Camera
Mount the camera at the desired location using the strap
mount, Python Lock cable, Articulating Ball Joint Mount, or
other desired mounting mechanism. Position the camera so
that it does not face East or West directly as the rising and
setting of the sun can cause false positive triggers.
Activate Camera
Set camera to “On” position and place in desired vantage
point to start capturing photos of game.

Page 6
Camera Overview

Page 7
Python Cable
Lock Hole
Strap
Mounts
Universal
¼ - 20 thread

Page 8
Camera Setup
Battery Installation
To remove batteries from unit, simply open the
camera and slide the battery release switch to the
left. Once the battery compartment is open, insert
batteries into camera, being careful to match the
orientation marked on your camera. After batteries
are inserted, close the battery compartment and
secure the battery release switch.
SD Card Installation
SD card slot is located on the bottom of the
camera, above the battery compartment.
Insert SD card with the label facing back of
camera. Only minimal resistance should be
felt as card is inserted and a click when the
card is fully inserted. Battery Release Switch
SD Card Slot

Page 9
Camera Conguration
Name Type Quality Timeout
Delay Detail
QSET 1 Photo Medium 30 sec 1 Photos
QSET 2 Video Medium 30 sec 10 sec Video
Cycle between camera modes by pressing the UP and DOWN arrows. The
camera mode will be displayed on the left side of the LCD Screen. This camera
comes equipped with two Quick Sets (QSET) containing some of our most
popular congurations. QSET 1 and 2 are dened in the table below. For alternate
congurations, press the UP or DOWN arrows until CUSTOM is displayed on the
left of the LCD screen and press ENTER.
Continue to next page for more information regarding each setting.

Page 10
OPERATION MODE: The operation mode setting is accessible immediately after the Time setting.
The screen will be blank with either Video or Photo displayed on the right side of screen.
Press Enter to change between Photo and Video mode.
DATE: This setting is used by the camera to display the correct date on the Info Bar of the image.
PHOTO BURST: This setting determines how many
photos are taken each time the camera is activated.
OPTIONS: 1 photo – 3 photos
PIR DELAY: This setting is used to determine how long
the camera will wait before restarting the PIR sensor
after taking a photo.
OPTIONS:
5 sec | 10 sec | 15 sec | 30 sec | 60 sec| 120 sec
RESOLUTION: This setting will determine the quality
of each image. A higher quality will result in better
photos and take more memory space.
OPTIONS: High | Med | Low
Note: This setting is only applicable in photo mode.
VIDEO LENGTH: This setting is used to determine
the length of time, in seconds, of a video recording
OPTIONS: 5 sec | 10 sec | 15 sec | 30 sec
Camera Conguration cont.
TIME: This setting is used by the camera to display the correct time of day on the Info Bar of the image.
PHOTO: In this mode the camera will
take a photo when trigger is activated. VIDEO: In this mode the camera will take a VIDEO when trigger is activated.
PIR DELAY: This setting is used to determine how long
the camera will wait before restarting the PIR sensor
after taking a video.
OPTIONS:
5 sec | 10 sec | 15 sec | 30 sec | 60 sec| 120 sec

Page 11
There are a few methods for viewing and deleting your les.
i. Using an SD Memory Card Reader/Viewer: You will simply
need to remove the SD card from the camera and insert it into
the reader to view the les; you can also delete them from this
device.
ii. Using your computer: This method requires an SD card slot to
be installed to your computer. Please refer to your computer’s
Owner’s Manual for the proper way of viewing the les.
iii. Obtain a mobile device adapter: This will allow you to plug one
end into the device, and, at the other end, insert the SD card.
Please refer to the vendor’s User Manual for the proper way of
viewing the les.
Viewing and Deleting Images

Page 12
Frequently Asked Questions
Q: Will I lose my images and settings if the batteries die?
A: You will lose your settings but not your images. The images are stored on your
external SD memory card so your images will be intact only on your card.
Q: Why is my camera taking pictures with nothing in front of it?
A: This camera is powered by motion activation. This can cause objects, like a tree
branch or moving water, within the camera frame to cause the camera to take a photo.
Q: Is there a warranty that comes with my camera or an extended warranty I can
purchase?
A: Your Stealth Cam Camera comes with a Limited 1-year warranty. Please contact
support at 1.877.269.8490 for more information.
Q: Can I mix batteries together?
A: No, you should never mix batteries. After your camera batteries die, always install
brand new batteries in your camera.
Q: Can I use rechargeable batteries in the camera?
A: Rechargeable batteries can be used but will cause battery percentage to be report-
ed incorrectly.

Page 13
Camera Care
Operating Conditions
This camera is designed to function in 14°F – 104°F (-10°C -
40°C) 20%-85% relative humidity, non-condensing.
Product Care
• When not in use, store camera in a cool, dust-free, environment.
• Handle camera with care.
• Camera is weather resistant only. Do not fully submerge camera in
water or other liquid. Doing so will void camera warranty.
• Only use same type of batteries to power camera. Do not mix old
and new batteries.
• Do not touch camera lens directly. Clean only with soft lens cloth.
• Use damp cloth to clean. DO NOT submerge camera.
• Remove batteries when camera is not in use for an extended time.
• Do not open camera housing to access internal parts. Doing so
could damage camera and void warranty.
Notice
Camera is an active electronic device. Attempting to service
internal parts may expose you to dangerous voltages and
other risks.

Page 14
NOTE: This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio or television receptions, which can be
determined by turning the equipment o󰀨 and on, the user is encouraged to try to correct the
interference by one or more of the following measure:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or Modications not expressly approved by the party responsible could void
the user’s authority to operate this device.
Product specications are subject to change. Good Sportsman Marketing, LLC is not
responsible for any photographic or typographical errors.
May be protected by one or more U.S. Patent numbers: 6,735,387 / 6,768,868 /
6,834,162 / 7,149,422 / 7,308,196 / 7,593,632 / 7,710,457 / 8,895,926.
IC WARNING
This device contains license-exempt transmitter(s) that comply with Innovation, Science and
Economic Development Canada’s license- exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device. This equipment meets the exemption from the routine evaluation limits
in section of RSS-102. It should be installed and operated with a minimum distance of 20cm
between the radiator and any part of your body.
FCC COMPLIANCE
GSM, LLC
STC-QV18 v3

Page 15
Your Stealth Cam Trail Camera is covered by a 365 Day Limited Warranty
on parts and labor from the date of original purchase, and purchases
must be made through an authorized dealer. The warranty covers defects
in workmanship and materials. The warranty does not apply to units
which have been damaged or abused intentionally or unintentionally. A
purchase from individuals or unauthorized Internet sites such as eBay
voids the warranty. Tampering with or altering the unit will void the
warranty. Any unauthorized service will void warranty. A copy of your
original sales receipt must be produced for any warranty service and
a Return Authorization (RA) number must be obtained from customer
service at 877-269-8490 prior to returning product. Stealth Cam is not
responsible for any lost untraceable packages or those without a Return
Authorization at the time of return.
Limited Warranty Information

Page 16
QV Series
Manuel d’instuction

Page 17
Pour vous assurer que le produit est utilisé à son plein potentiel, nous vous recom-
mandons de consulter notre site Web pour les nouvelles mises à jour du produit. Si
votre appareil photo rencontre un problème, veuillez consulter notre site Web pour
déterminer si vous utilisez la dernière version du micrologiciel ou du logiciel.
Remarquer
SOUTIEN TECHNIQUE
EMAIL:
[email protected]
Veuillez prévoir 48 heures pour le
courrier électronique
réponse.
GSM, LLC
P.O. Box 535189
Grand Prairie, TX 75053-9504
SERVICE CLIENTS
CONTACT & HEURES
Sans frais: 877-269-8490
HEURES DU CENTRE D’APPELS
Lun - ven / 8h - 17h (CST)
SITE INTERNET
www.stealthcam.com
Nous contacter

Page 18
Table of Contents
À propos de votre appareil photo 20
Guide d’installation rapide 21
Présentation de la caméra 22
Conguration de la caméra 24
Conguration de la caméra 25
Conguration de la caméra (suite) 27
A󰀩chage et suppression d’images 28
Questions fréquemment posées 29
Salle de soins 30
CONFORMITÉ DE FCC 31
Informations sur la garantie limitée 32

Page 19
À propos de votre appareil photo
Conception résistante à l’eauI
Votre appareil photo est protégé des éléments grâce à un boîtier étanche et
robuste.
Options de réglage rapide
Installation en quelques secondes avec des options préprogrammées.
Mode de tir rapide en rafale
Mode rafale à tir rapide, expositions multiples par déclenchement.
No Glow IR LEDs
Illuminez parfaitement vos photos de nuit avec lumières LED IR.
Mémoire extensible
Élargissez votre stockage à bord avec une carte mémoire SD jusqu’à 32 Go.
Conception écoénergétique
Complètement redynamisé pour optimiser l’e󰀩cacité énergétique.

Page 20
Guide d’installation rapide
Insérez les piles et la carte SD
Installez 8 piles AA et une carte SD de classe 10 dans l’appareil photo.
Monter la caméra
Montez la caméra à l’emplacement souhaité à l’aide du support de
sangle, du câble de verrouillage Python, du support de rotule articulée
ou de tout autre mécanisme de montage souhaité. Positionnez la
caméra de manière à ce qu’elle ne soit pas directement orientée vers
l’Est ou l’Ouest car le lever et le coucher du soleil peuvent provoquer de
faux déclencheurs positifs.
Activer la caméra
Placez l’appareil photo en position “On” et placez-vous dans le point de
vue souhaité pour commencer à capturer des photos du jeu.