Steel City 65-300 X1 User manual

C US
VER.06.2016
Should you require assistance,
please have available your:
Model no.: __________________
Serial no.: __________________
STOCK FEEDER
WNER’S MANUAL
65-500 X1
65-300 X1

Page 2

Page 3
This user manual is intended for use by anyone working with this machine. It should be kept available
for immediate reference so that all operations can be performed with maximum efficiency and safety.
Do not attempt to perform maintenance or operate this machine until you have read and understand
the information contained in this manual.
The drawings, illustrations, photographs, and specifications in this user manual represent your machine
at time of print. However, changes may be made to your machine or this manual at any time with no
obligation to Steel City.
I TRODUCTIO ...............................................................3
TABLE OF CO TE TS ....................................................3
WARRA TY......................................................................4
PRODUCT SPECIFICATIO S..........................................5
GE ERAL SAFETY ..........................................................6
PRODUCT SAFETY .........................................................8
ELECTRICAL A D GROU DI G I STRUCTIO S ........9
ASSEMBLY .....................................................................10
ADJUSTME TS..............................................................12
MAI TE A CE..............................................................16
PARTS ............................................................................17
INTR DUCTI N
TABLE F C NTENTS

Page 4
WARRANTY
STEEL CITY WARRANTY
The manufacturer warrants its machines to be free from defects in workmanship and materials for a period of
2 years from the date of the original purchase for Steel City shop machines or for a period of 1 year for Titanium
production machines; subject to the following conditions :
A- Warranty applies to the original buyer only and may not be transferred. Original proof of purchase is
required.
B- Warranty is void if repairs or alterations are made to the machine by an unauthorized service center without
the direct consent of the manufacturer or its representative.
C- Warranty does not include defects, failures or breakages directly or indirectly caused by or resulting from
improper use, improper or lack of maintenance, abuse or misuse, negligence, accidents, damages in
handling or transportation, or normal wear and tear of any part or component.
D- Accessories and wear items such as motor, switch, bearings, drive belt or other accessories are covered
for 1 year.
E- Consumables such as blades, knives, bits, sandpaper or others are not covered.
To file a warranty claim, customer may contact his dealer or email [email protected]
The manufacturer or its representative will inspect, repair or replace any part that has proven to be defective in
workmanship or material, provided that the customer sends the product prepaid to a designated authorized
service center and provides reasonable time to proceed.
If judged on warranty, the manufacturer or its representative will return the repaired product prepaid or will replace
it by a new one at its choice. On the contrary, if it is determined that there is no defect or that the problem resulted
from causes not within the scope of the warranty, it will dispose of or return the product at customer’s expenses,
following customer’s instructions.
The manufacturer or its representative shall not be held liable for any special, indirect, incidental, punitive or
consequential damages, including and without limitation loss of profits arising from or related to the warranty,
the breach of any agreement, the operation or the use of its machines.
Note:
The specifications in this manual are provided for informational purposes only and are subject to rectification
without notice. Some measures have been slightly rounded for ease of reading. Unless otherwise noted, they
should be considered for reference only.
Steel City reserves the right to make certain improvements to the design and appearance of its machines,
components, accessories or parts without notice and without the obligation to perform them on existing models.

Page 5
Model 65-300 65-500
Motor DC Brushless Servo Motor
Voltage 115/230V, 1 Phase
Power 375 Watts / ½ HP
umber of rollers 34
Roller size Ø120 x 60mm (Ø120 x 25mm optional)
Roller suspension 18 mm / ¾ ‘’
Feeding speed 2-22 m/min / 7-72 fpm
Max. feeding width 170 mm
Forward/reverse Yes
Weight
• body 23 kg (51lbs)
• stand 30 kg (66lbs)
PR DUCT SPECIFICATI NS

Page 6
All federal and state laws and any regulations having
jurisdiction covering the safety requirements for use of this
machine take precedence over the statements in this
manual. Users of this machine must adhere to all such
regulations.
Below is a list of symbols that are used to attract your
attention to possible dangerous conditions.
These are safety alert symbols. They are used to alert you
to potential personal injury hazards. Obey all safety
messages that follow these symbols to avoid possible injury
or death.
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, WILL result in serious injury or death.
Indicates a potentially hazardous situation which, if not
avoided, C ULD result in serious injury or death.
Exposure to the dust created by power
sanding, sawing, grinding, drilling and other
construction activities may cause serious
and permanent respiratory or other injury,
including silicosis (a serious lung disease),
cancer, and death. Avoid breathing the dust, and avoid
prolonged contact with dust. The dust may contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Always operate tool in well ventilated area and provide
for proper dust removal. Use a dust collection system
along with an air filtration system whenever possible.
Always use properly fitting IOSH/OSHA approved
respiratory protection appropriate for the dust exposure,
and wash exposed areas with soap and water.
DANGER
!
This manual is not totally comprehensive. It does not and can not convey every possible safety and
operational problem which may arise while using this machine. The manual will cover many of the basic
and specific safety procedures needed in an industrial environment.
ALWAYS wear eye protection. Any
machine can throw debris into the eyes
during operation, which could cause severe
and permanent eye damage. Everyday
eyeglasses are N T safety glasses.
ALWAYS wear Safety Goggles (that comply with A SI
standard Z87.1) when operating power tools.
SAFETY
WARNING
!
ALWAYS wear hearing protection. Plain
cotton is not an acceptable protective
device. Hearing equipment should comply
with A SI S3.19 Standards.
WARNING
!
WARNING
!
WARNING
!
T REDUCE the risk of electrical shock.
D N T use this machine outdoors. D
N T expose to rain or moisture. Store
indoors in a dry area. D N T handle the
plug with wet hands.
1. To avoid serious injury or damage to the machine, read
the entire User Manual before assembly and operation
of this machine.
2. Serious personal injury may occur if normal safety
precautions are overlooked or ignored. Accidents are
frequently caused by lack of familiarity or failure to pay
attention. Obtain advice from supervisor, instructor, or
another qualified individual who is familiar with this
machine and its operation.
3. ST P using this machine, if at any time you experience
difficulties in performing any operation. Contact your
supervisor, instructor or machine service center
immediately.
WARNING
!
CHILDPR F THE W RKSH P AREA
by removing switch keys, unplugging tools
from the electrical receptacles, and using
padlocks. D N T use near or around
children.
WARNING
!

Page 7
4. Prevent electrical shock. Follow all electrical and safety
codes, including the ational Electrical Code ( EC) and
the Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring should be
made by qualified personnel only.
5. ALWAYS be sure that the power switch is in the “ FF”
position and unplug the machine from the electrical
receptacle when making adjustments, changing parts or
performing any maintenance.
6. AV ID ACCIDENTAL STARTING. Make sure that the
power switch is in the “ FF” position before plugging in
the power cord to the electrical receptacle.
7. NEVER leave a machine running, unattended. Turn the
power switch to the FF position. D N T leave the
machine until it has come to a complete stop.
8. THE USE of extension cords is not recommended for
220V equipment. It is better to position your equipment
and install the wiring to eliminate the need for an extension
cord. If an extension cord is necessary, refer to the chart
in the Grounding Instructions section to determine the
minimum gauge for the extension cord. The extension
cord must also contain a ground wire and plug pin.
9. D N T pull a machine by the power cord. NEVER
allow the power cord to come in contact with sharp
edges, hot surfaces, oil or grease.
10. D N T unplug a machine by pulling on the power
cord. ALWAYS grasp the plug, not the cord.
11. REPLACE a damaged cord immediately. D N T use
a damaged cord or plug if the machine is not operating
properly, or has been damaged, left outdoors or has
been in contact with water.
12. NEVER remove any chips without turning off the
machine and disconnecting the power.
13. NEVER turn on the machine if the workpiece is in
contact with the blade.
14. ENSURE that the machine sits firmly on the floor before
using. If the machine wobbles or is unstable, correct the
problem by using shims or blocks prior to operation.
15. ALWAYS keep hands and fingers away from the blades
when operating.
16. D N T USE the machine to perform an operation for
which it was not designed. It will be safer and provide
high quality job by only performing operations for which
the machine was intended.
17. Every work area is different. Always consider safety first,
as it applies to your work area. Use this machine with
caution. Failure to do so could result in serious personal
injury and damage to the machine.
18. D N T stand on a machine. Serious injury could result
if it tips over or you accidentally contact any moving part.
19. D N T store anything above or near the machine.
20. REM VE ALL MAINTENANCE T LS from the
immediate area prior to turning the machine O .
21. MAINTAIN your balance. D N T extend yourself over
the tool. Wear oil resistant rubber soled shoes. Keep
floor clear of debris, grease, and wax.
22. D N T operate any machine or tool if under the
influence of drugs, alcohol, or medication.
23. MAINTAIN all machines with care. ALWAYS KEEP
the machine clean and in good working order. KEEP all
blades and tool bits sharp and free of all rust and pitch.
24. EACH AND EVERY time, check for damaged parts prior
to using any machine. Carefully check all guards to see
that they operate properly, are not damaged, and
perform their intended functions. Check for alignment,
binding or breakage of all moving parts. Any guard or
other part that is damaged should be immediately
repaired or replaced. Check material for loose knots.
25. Safety decals are on this machine to warn and direct
you to how to protect yourself or visitors from personal
injury. These decals MUST be maintained so that they
are legible. REPLACE decals that are not legible.
26. KEEP protective guards in place and in working order.
27. Check material for loose knots, nails and other defects.
28. ALWAYS keep the work area clean, well lit, and
organized. D N T work in an area that has slippery
surfaces. Keep floor clear of debris, grease, and wax.
29. SECURE all work. When it is possible, use clamps or
jigs to secure the workpiece. This is safer than
attempting to hold the workpiece with your hands.
30. STAY ALERT, watch what you are doing, and use
common sense when operating any machine. D N T
operate any machine tool while tired or under the
influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
31. USE NLY recommended accessories. Use of incorrect
or improper accessories could cause serious injury to
the operator and cause damage to the machine. If in
doubt, D N T use it.
32. Wear proper clothing, D N T wear loose clothing,
gloves, neckties, or jewelry. These items can get caught
in the machine during operations and pull the operator
into the moving parts. Users must wear a protective
cover on their hair, if the hair is long, to prevent it from
contacting any moving parts.
33. Keep visitors and children away from any machine.
D N T permit people to be in the immediate work
area, especially when the machine is operating.
34. D N T use a machine as a toy.
35. D N T use electrical tools in the presence of
flammable liquids or gasses.
36. SAVE these instructions and refer to them frequently
and use them to instruct other users.
37. Establish a SAFETY Z NE around shop machinery.
A clearly defined “no-go” zone on the floor around each
machine. Take a few moments to either paint (using
non-slip paint) or using tape, define on the floor the limits
or perimeter of each machines safety zone.

Page 8
1. NLY PERATE workpiece that exceed 6” dimension
between the jointer’s tables or shaper’s guide.
2. NLY PERATE workpiece that exceed 6” c/c
dimension between feeder rollers.
3. ALWAYS consider the cutterhead diameter and rotation
speed to adjust feed rate for best results.
4. BEF RE pluging in and starting the machines (feeder
AND the machine on which the feeder is mounted), be
sure all locking levers are well locked.
PR DUCT SAFETY

Page 9
To reduce the risk of electric shock, follow all
electrical and safety codes, including the
ational Electric Code ( EC) and the
Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring
should be made by qualified personnel only.
WARNING
!
This machine MUST BE GR UNDED
while in use to protect the operator from
electric shock.
WARNING
!
In the event of a malfunction or breakdown, GR UNDING
provides the path of least resistance for electric current and
reduces the risk of electric shock. The plug MUST be
plugged into a matching electrical receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
If a plug is provided with your machine D N T modify the
plug. If it will not fit your electrical receptacle, have a
qualified electrician install the proper connections to meet
all electrical codes. All connections must also adhere to all
of OSHA mandates.
IMPR PER ELECTRICAL C NNECTI N of the
equipment-grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or
without yellow stripes) is the equipment-grounding
conductor.
D N T connect the equipment-grounding conductor to a
live terminal if repair or replacement of the electric cord or
plug is necessary.
Check with a qualified electrician or service personnel if you
do not completely understand the grounding instructions,
or if you are not sure the tool is properly grounded.
MINIMUM REC MMENDED GAUGE F R EXTENSI N C RDS (AWG)
115/230 V LT PERATI N NLY
25’ long 50’ long 100’ long
0 to 6 Amps 18 AWG 16 AWG 16 AWG
6 to 10 Amps 18 AWG 16 AWG 14 AWG
10 to 12 Amps 16 AWG 16 AWG 14 AWG
12 to 15 Amps 14 AWG 12 AWG ot
recommended
◊ EXTENSI N C RDS
◊ PLUGS/RECEPTACLES
MAKE SURE the circuit breaker does not
exceed the rating of the plug and
receptacle.
WARNING
!
To reduce the risk of fire or electrical
shock, use the proper gauge of extension
cord. When using an extension cord, be
sure to use one heavy enough to carry the
current your machine will draw.
WARNING
!
The smaller the gauge-number, the larger the diameter of
the extension cord is. If in doubt of the proper size of an
extension cord, use a shorter and thicker cord. An
undersized cord will cause a drop in line voltage resulting
in a loss of power and overheating.
WARNING
!
If you are using an extension cord outdoors, be sure it is
marked with the suffix “W-A” (“W” in Canada) to indicate
that it is acceptable for outdoor use.
Make certain the extension cord is properly sized, and in
good electrical condition. Always replace a worn or
damaged extension cord immediately or have it repaired by
a qualified person before using it.
Protect your extension cords from children, sharp objects,
excessive heat, and damp or wet areas.
USE NLY a 3-wire extension cord that has
a 3-prong grounding plug and a 3-pole
receptacle that accepts the machine’s
plug.The third prong is used to ground the
tool and provide protection against
accidental electric shock. D N T remove the third.
◊ MAGNETIC SAFETY SWITCH
If the machine is equipped with a magnetic safety switch
you must to reset the overload protection switch after an
overload.
1. Remove the control box cover.
2. Press the reset button.
3. Reinstall the control box cover.
Make certain that the machine is disconnected
from the power source
WARNING
!
ELECTRICAL AND GR UNDING INSTRUCTI NS

Page 10
Handwheel depth
adjustment
Column
Mounting
bracket
Rotation of the
column locking
handle
Height locking
handle
Lateral
locking
handle
Bracket rotation
locking handle
Motor
Arm
Bracket
Handwheel lateral
adjustment
Inclined rotation
locking handle
Switch
Indexable
knob
Feeder
{
Stand
{
B
K
J
D
C
I
A
E
F
L
N
M
G
H
Sticker with
pointer
Ring
R
S
MEMBER INDENTIFICATI N

Page 11
WARNING
!
The stock feeder and auxiliary machine to which you are
mounting the stock feeder should be disconnected from
the power source during installation.
NOTE: Keep in mind the length of the horizontal arm
when mounting the stock feeder so you have room for
proper adjustment.
NOTE: Leave enough space around the work area for
loading and off-loading stock.
IM ORTANT: ake sure the base machine is secured
to the floor or has sufficient supporting weight that will
prevent both units from toppling over when feeder is
swung over the edge of the base unit. Fig. 1
Fig. 1
Make certain that both machines are disconnected
from the power source.
1. Position the base by the rear-side of the outfeed with
the feeder towards the infeed direction. Fig. 2
ATTACHING THE
TABLE M UNTING BRACKET
Fig. 2
WARNING
!
2. Clean the mounting surface and apply the supplied
self-adhesive drilling template. Fig. 3
3. atch the template to your base, mark the holes with
a center punch and remove the template.
4. Drill and tap for 12 bolts (not provided).
NOTE: DO NOT drill through any table ribs or
table supports.
5. Secure the mounting bracket to the table with four
12 bolts and lock washers. If surface is not thick
enough for proper tapping, use appropriate length
bolts and fasten using flat washers and hex lock nuts
(not provided).
Fig. 3
ATTACHING THE SUPP RT
ASSEMBLY
1. Loosen locking lever (A) and insert stand in base. Fig. 4
2. Assemble handle. Fig. 4
Fig. 5
A
ASSEMBLY

Page 12
3. Insert over-arm (1) into elevating bracket, insert
handwheel (2) and turn it to scroll in the over-arm;
then fasten screw (3) to keep handwheel in position.
Fig. 6
4. Insert the inclined adjustment ring (R) to over-arm,
place over-arm cone onto the end of the over-arm
and tighten one of the screw temporarily. Fig. 7 & 8
5. Clean up the surface with rubbing alcohol before
placing the indicator sticker (S) onto the cone.
Fig. 8 & 9
6. Insert the electric wire into the side hole of the cone.
8.1
7. Install the Easy Flip handle, do not over tighten. The
handle shall remain rotatable. Fig. 10
Fig. 6
Fig. 7 Fig. 8
Fig. 9
Fig. 10
8. Install Control Joint and feeder:
A– Place the 45° Control Joint onto the feeder
cone and tighten the handle. Fig. 11
B- Place the feeder on the machine table, lower the
over-arm so the over-arm cone connects to the
Control Joint, and tighten the lever. Fig. 12
9. Set-up the reference points:
Position the feeder in regular infeed position.
A– 3 rollers feeder: position so tooling is after the
first roller.
B– 4 rollers feeder: position so tooling is between
second and third roller.
Lower feeder rollers onto the machine table to ensure
they are aligned. The emo-Position pin should be
locked-in. Loosen the screws and adjust the over-arm
cone if the rollers are not parallel to surface.
The inclined adjustment ring should be firmly attached
to the over-arm cone, with the in-line indicator pointing
to 0. Fig. 9
Fig. 11
Fig. 12

Page 13
WARNING
!
BASIC FEEDER AND SUPPRT
ASSEMBLY M VEMENTS
Make certain that both machines are disconnected
from the power source.
1. To rotate the feeder assembly, loosen locking lever
(A) on the base and swing the assembly into the
desired position . Fig. 13
2. To raise or lower the feeder, loosen the locking lever
(D) and turn the handle (E).
3. To move the feeder in or out, loosen locking lever (B)
and rotate the handwheel (C).
4. To adjust the position of the feeder in relation to the
fence, loosen locking lever (F) and rotate the feeder
body.
5. To adjust angle of the feeder in relation to the table,
loosen the pull handle (G). Pull-out the
emo-Positioning pin (H), grab the Flip Handle
( 1, Fig. 10) and rotate the feeder body.
6. Tighten all locking levers after adjustments
are complete.
Fig. 13
SIDE FEEDING
1. To rotate the feeder assembly, loosen locking lever
and swing feeder off the table.
2. Release the Pull handle (1), grab the Flip Handle, pull
up the emo-Positioning pin (2) Fig 14 and turn the
feeder according to vertical position.
Swing feeder back to table, tighten all levers.
Fig. 14
3. For the 4 rollers feeder: proceed step 1. Then loosen
lever (F), turn Control-Joint 90° clockwise ( Fig. 15 )
and proceed step 2.
Fig. 15
INCLINED FEEDING
1. Loosen the lever and swing the feeder off the table.
2. Loosen screws on the over-arm cone (K), turn the
Control-Joint along the feeder body and set the
desired angle (S), then tighten the screws (K). Fig. 16
3. Loosen levers Fand G, grab the Flip Handle, pull
up the emo-Positioning pin, turn the feeder back to
horizontal position, swing feeder back in operating
position, make sure all rollers are aligned with the
workpiece and then tighten all levers. Fig. 17
4. Workpiece should lean against the fence closely when
feeding. Rollers should have a pressing angle to the
fence during infeed. The gap between infeed rollers
should be 3-4 mm larger than outfeed rollers. Fig. 18.
5. During side feeding, the gap between infeed rollers
should be 3-4 mm larger than outfeed rollers.
6. The emo-Positioning pin has default pressing angle
setting. After initial gap adjustment, when switching
to side feeding, gap readjustment is not necessary.
Fig. 16 Fig. 17
Fig. 18
ADJUSTMENTS

Page 14
ST CK FEEDER HEIGHT
ADJUSTMENT
Position the stock feeder height so that the distance
between the table and the feed rollers is approximately
1/8’’ less than the thickness of the workpiece. Fig. 19.
Fig. 19
DIGITAL C NTR L PANEL
ST CK FEEDER R LLER
ALIGNMENT
Position the stock feeder so that all of the rollers make
contact with and set squarely on the workpiece. Fig. 20
Fig. 20
1. Power / speed
Adjustment Dial
3. Feeding Direction Button
2. Speed Setting Button
4. Feeding Direction Button
1. Speed
adjustment
Speed range 2 – 22 M/min
(7 – 72 FPM).Press to switch on
power and pause while in
motion.
2. Setting
button
Speed setting: press SET
button and dial to desired speed.
3.
4.
Feeding
direction
button
Change feed direction during
operation: Press Feeding direction
button 2 times, reverse direction
will be set in lowest speed.
Retrieve original Feed setting:
Press Power dial 2 times.

Page 15
OWER CONNECTION
Make sure your power supply matches the motor
requirements.
Connecting power wire shall be larger than 18AWG x 4C
wire. Power connections and ground must meet with
local electrical codes and safety regulations.
To prevent pull and drag of the wire when adjusting the
feeder, ensure sufficient length of cable has been
reserved when installing the power wire. Fig. 21
WARNING
!
Fig. 21
ROLLER RE LACEMENT AND
O ERATION
1. Two types of rollers are available for selection:
Ø120 x 60mm wide (GR121) Fig. 22 and
Ø120 x 25mm wide (RU21) Fig. 23.
Fig. 22 Fig. 23
2. Outer roller can be removed when operating with larger
diameter tooling. Fig. 24
3. Inner roller could be removed from roller set to prevent
compressing workpiece to the saw blade during circular
saw operation. Fig. 25
4. ixed roller set up can be used for different feeding
conditions.
Fig. 24
Fig. 25
The feeder is pre-wired for 110V single phase
operation. lease refer to Wiring Diagram should
you wish to change to 220V single phase operation.
Wiring connections will need to be modified.

Page 16
WIRING DIAGRAM
1. AC110V-230V
2. AC380V-400V
3. Power board
wiring indications

Page 17
LUBRICATION AND MAINTENANCE
Make certain that both machines are disconnected
from the power source.
GREASE
1. Every 200 hours or 30 days, the rollers should be
greased using a #2 grease or equivalent. Each roller has
grease fitting; refer to indication sticker for grease
locations. Fig. 26
2. Gears and chains: periodically lubricate the gears and
chains with a #2 grease or equivalent.
GEAR OIL CHANGE
After the first 200 working hours, or 30 days, the gearbox
oil should be changed. After the initial oil change, change
every 1000 working hours, or 6 months, with a good
quality gear oil. This recommendation is based on
8 hours/day.
To change oil:
Swing the feeder off the table, open the cover, turn the
feeder upside down, remove the oil cap and completely
drain all oil into a catch pan. After drained, turn the feeder
on vertical feeding position, pour gear oil referring to the
indication on the Lubricant Gauge and reinstall the oil
cap. Fig. 27, 28
Recommended Gear oil: OBIL obilgear 630,
Shell/Omala 150 BP, Energol GR-XP 150, or equivalents.
WARNING
!
Fig. 26
Fig. 27 Fig. 28
CLEANING
Remove working waste (shavings, sawdust) from feeder
by air gun after each use. 50 PSI max.
TROUBLESHOOTING
If an error message occur on the display panel, see
below explanation:
The motor fails to start, please check if anything
stuck in the feeder.
The temperature of driver is too high.
The temperature of the motor is too high.
1. Restart the main power after clearing the possible error.
2. If you cannot identify the cause of the problem, please
seek further technical support.
MAINTENANCE

Page 18
Model 65-300 Feeder unit
PARTS

Page 19
!
06A
S65 300
M 06A
06A
Roller Spindle Kit
3
21A-2.
S65 300 M 21A 2
U010008
Oil Filler Cap
1
38A
S65 300 M 38A
U210041
Roller
3
06A-1
S65 300
M 06A 1
A400005
Roller Spindle
1
22A
S65 300 M 22A
22A
Control Panel Kit
1
39A
S65 300 M 39A
39A
Pivot-Joint Kit
1
06A-2
S65 300
M 06A 2
A510003
Washer
1
22A-1
S65 300 M 22A 1
J011235
Control Panel
1
39A-1
S65 300 M 39A 1
A250006
Pivot-Joint
1
06A-3
S65 300
M 06A 3
N11012H
Nut
1
22A-2.
S65 300 M 22A 2
S050308-001
Tap Screw
3
39A-2
S65 300 M 39A 2
S900825
Cap Screw
4
06A-4
S65 300
M 06A 4
N011630
Flat Washer
1
23A
S65 300 M 23A
23A
Control Box Kit
1
39A-3.
S65 300 M 39A 3
N810816
Lock Pin
2
06A-5.
S65 300
M 06A 5
N11016R
Nut
1
23A-1
S65 300 M 23A 1
U010271
Control Box
1
40A
S65 300 M 40A
A250007
45 Degree Swivel Kit
1
07A
S65 300
M 07A
07A
Sprocket Kit
3
23A-2.
S65 300 M 23A 2
S050412-001
Tap Screw M4x12L
1
41A
S65 300 M 41A
G020113
Screw (M16XP1.5)
1
07A-1
S65 300
M 07A 1
A500309
Sprocket
1
24A
S65 300 M 24A
P360007
Control Panel (Metric System)
1
42A
S65 300 M 42A
42A
Pull Handle Kit
1
07A-2
S65 300
M 07A 2
N050057
Lock Washer
2
25A
S65 300 M 25A
P360010
Control Panel (Imperial System)
1
42A-1
S65 300 M 42A 1
T060032
Pull Handle
1
07A-3.
S65 300
M 07A 3
S900620
Cap Screw
2
26A
S65 300 M 26A
U010272
Speed Knob
1
42A-2.
S65 300 M 42A 2
N810622
Lock Pin
1
08A
S65 300
M 08A
08A
Housing Frame Kit
1
27A
S65 300 M 27A
27A
Protecting Cover Kit
1
43A
S65 300 M 43A
43A
Locating Pin Kit
1
08A-1
S65 300
M 08A 1
C020100
Housing Frame
1
27A-1
S65 300 M 27A 1
U010274
Protecting Cover
1
43A-1
S65 300 M 43A 1
G320275
Locating Pin
1
08A-2
S65 300
M 08A 2
A500301
Bushing
1
27A-2.
S65 300 M 27A 2
S900525
Cap Screw
1
43A-2
S65 300 M 43A 2
N930039
Comp. Spring
1
08A-3
S65 300
M 08A 3
U010273
Lubricant Gauge
1
28A
S65 300 M 28A
28A
Wire clamp Kit
1
43A-3.
S65 300 M 43A 3
T005022
Pin Knob
1
08A-4
S65 300
M 08A 4
C070004
Lubricant Gauge Panel
1
28A-1
S65 300 M 28A 1
U010278
Wire clamp
1
44A
S65 300 M 44A
J625413
Power Cord
1
08A-5
S65 300
M 08A 5
P340474
Oil/Grease Sticker
1
28A-2.
S65 300 M 28A 2
S500412
PH. Screw ( M4X12mmL)
2
45A
S65 300 M 45A
J625414
Power Cord
1
08A-6
S65 300
M 08A 6
P340498
Warning Mark
2
29A
S65 300 M 29A
J530003
Cable Gland (PG-11L)
1
46A
S65 300 M 46A
J625415
Power Cord(18#x3C)
1
08A-7
S65 300
M 08A 7
S100610
Set Screw
3
30A
S65 300 M 30A
30A
Drive Plate Kit ( 230V)
1
47A
S65 300 M 47A
J625416
Power Cord(18#x4C)
1
09A
S65 300
M 09A
09A
Flip Handle-Kit
1
30A-1
S65 300 M 30A 1
J011236A
Drive Plate
1
48A
S65 300 M 48A
U210042
Separated Roller ȴ120x25mm
6
09A-1
S65 300
M 09A 1
U010275
Flip Handle
1
30A-2.
S65 300 M 30A 2
S900540
Cap Screw
2
09A-2
S65 300
M 09A 2
S901050
Cap Screw
1
31A
S65 300 M 31A
P300125
Motor Label (100~240V)
1
Parts list for motor unit 65-300

Page 20
!
06A
S65 300
M 06A
06A
Roller Spindle Kit
3
21A-2.
S65 300 M 21A 2
U010008
Oil Filler Cap
1
38A
S65 300 M 38A
U210041
Roller
3
06A-1
S65 300
M 06A 1
A400005
Roller Spindle
1
22A
S65 300 M 22A
22A
Control Panel Kit
1
39A
S65 300 M 39A
39A
Pivot-Joint Kit
1
06A-2
S65 300
M 06A 2
A510003
Washer
1
22A-1
S65 300 M 22A 1
J011235
Control Panel
1
39A-1
S65 300 M 39A 1
A250006
Pivot-Joint
1
06A-3
S65 300
M 06A 3
N11012H
Nut
1
22A-2.
S65 300 M 22A 2
S050308-001
Tap Screw
3
39A-2
S65 300 M 39A 2
S900825
Cap Screw
4
06A-4
S65 300
M 06A 4
N011630
Flat Washer
1
23A
S65 300 M 23A
23A
Control Box Kit
1
39A-3.
S65 300 M 39A 3
N810816
Lock Pin
2
06A-5.
S65 300
M 06A 5
N11016R
Nut
1
23A-1
S65 300 M 23A 1
U010271
Control Box
1
40A
S65 300 M 40A
A250007
45 Degree Swivel Kit
1
07A
S65 300
M 07A
07A
Sprocket Kit
3
23A-2.
S65 300 M 23A 2
S050412-001
Tap Screw M4x12L
1
41A
S65 300 M 41A
G020113
Screw (M16XP1.5)
1
07A-1
S65 300
M 07A 1
A500309
Sprocket
1
24A
S65 300 M 24A
P360007
Control Panel (Metric System)
1
42A
S65 300 M 42A
42A
Pull Handle Kit
1
07A-2
S65 300
M 07A 2
N050057
Lock Washer
2
25A
S65 300 M 25A
P360010
Control Panel (Imperial System)
1
42A-1
S65 300 M 42A 1
T060032
Pull Handle
1
07A-3.
S65 300
M 07A 3
S900620
Cap Screw
2
26A
S65 300 M 26A
U010272
Speed Knob
1
42A-2.
S65 300 M 42A 2
N810622
Lock Pin
1
08A
S65 300
M 08A
08A
Housing Frame Kit
1
27A
S65 300 M 27A
27A
Protecting Cover Kit
1
43A
S65 300 M 43A
43A
Locating Pin Kit
1
08A-1
S65 300
M 08A 1
C020100
Housing Frame
1
27A-1
S65 300 M 27A 1
U010274
Protecting Cover
1
43A-1
S65 300 M 43A 1
G320275
Locating Pin
1
08A-2
S65 300
M 08A 2
A500301
Bushing
1
27A-2.
S65 300 M 27A 2
S900525
Cap Screw
1
43A-2
S65 300 M 43A 2
N930039
Comp. Spring
1
08A-3
S65 300
M 08A 3
U010273
Lubricant Gauge
1
28A
S65 300 M 28A
28A
Wire clamp Kit
1
43A-3.
S65 300 M 43A 3
T005022
Pin Knob
1
08A-4
S65 300
M 08A 4
C070004
Lubricant Gauge Panel
1
28A-1
S65 300 M 28A 1
U010278
Wire clamp
1
44A
S65 300 M 44A
J625413
Power Cord
1
08A-5
S65 300
M 08A 5
P340474
Oil/Grease Sticker
1
28A-2.
S65 300 M 28A 2
S500412
PH. Screw ( M4X12mmL)
2
45A
S65 300 M 45A
J625414
Power Cord
1
08A-6
S65 300
M 08A 6
P340498
Warning Mark
2
29A
S65 300 M 29A
J530003
Cable Gland (PG-11L)
1
46A
S65 300 M 46A
J625415
Power Cord(18#x3C)
1
08A-7
S65 300
M 08A 7
S100610
Set Screw
3
30A
S65 300 M 30A
30A
Drive Plate Kit ( 230V)
1
47A
S65 300 M 47A
J625416
Power Cord(18#x4C)
1
09A
S65 300
M 09A
09A
Flip Handle-Kit
1
30A-1
S65 300 M 30A 1
J011236A
Drive Plate
1
48A
S65 300 M 48A
U210042
Separated Roller ȴ120x25mm
6
09A-1
S65 300
M 09A 1
U010275
Flip Handle
1
30A-2.
S65 300 M 30A 2
S900540
Cap Screw
2
09A-2
S65 300
M 09A 2
S901050
Cap Screw
1
31A
S65 300 M 31A
P300125
Motor Label (100~240V)
1
Parts list for motor unit 65-300 - cont’d