STEELE PRODUCTS SP-HD909 User manual

2
Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS
Warning! When using electrical appliances, basic precautions should always be followed
INSTRUCTIONS FOR USE AND CARE
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, use handles when moving this heater. Keep combustible
materials such as furniture, pillows, bedding, papers, clothes and curtains at least
3 feet (0.9m) from the front of the heater and keep them away from the sides and
rear.
3. Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate the heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Return heater to
authorized service facility for examination, electrical or mechanical
adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist
indoor locations. Never locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or
9. This appliance has a polarized plug (one blade is wider than the other). To
feature..
10. To prevent overloading a circuit,
do not plug the heater into a circuit that already has other appliances working.
the AC outlet (receptacle) and plug may cause overheating and distortion of the
the plug and pull it from the wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust
not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas
16. Use this heater only as described in this manual. Any other use not
persons.

3
Owner’s Manual
17. Avoid the use of an extension cord because the extension cord may overheat
shall be No.14 AWG minimum size and rated not less than 1875 watts.
18. The output of this heater may vary and its temperature may become intense
enough to burn exposed skin. Use of this heater is not recommended for
persons with reduced sensitivity to heat or an inability to react to avoid burns.
19. SAVE THESE INSTRUCTIONS
FAN HEATER
1. Thermostat
2. Selection Switch
3. PTC Element
4. Oscillation Base
12
3
4

4
Owner’s Manual
HEAT SWITCH FUNCTIONS
Functions are selected by turning rotary switch to the desired position.
-----Provides 1500 watts of heat output operation and oscillation.
-----Provides 800 watts of heat output operation
-----Fan only operation for cooling comfort.
ELECTRICAL RATINGS
This product is rated (1500W) at 120V, 60 Hz.
OPERATION
away from any wall or combustible material.
* With the selection switch in the OFF " " position, plug the heater into a
polarized 120V outlet.
* Turn the thermostat control fully clockwise to the "MAX" setting.
* To turn the heater on, selection switch while turning it clockwise to the desired
position ( for 1500 W, or for 800 W). The power light will illuminate.
* When the room reaches a comfortable temperature, slowly turn the thermostat
thermostat setting equals the room temperature. At this setting, the thermostat
temperature.
* If using the oscillation feature, at the point your desired temperature is reached,
the heater will stop oscillating.
* Turn the selection switch to OFF " "and unplug the heater when you are
IF YOUR HEATER FAILS TO OPERATE:
* Be sure it is plugged in and that the electrical outlet is working.
Unplug the heater and wait at least ten minutes for it to cool. Carefully remove
the obstruction. Plug the heater back in and restart it as described under
OPERATION.
* If you still notice the same defect above mentioned, remove the plug from the
socket and have the appliance serviced by authorized service personnel only.
* Check that the thermostat is not set too low. With the selection switch set to a
heat setting, turn the thermostat up (clockwise) until the heater restarts.

5
Owner’s Manual
CLEANING AND STORAGE
storage.
* Turn the heater OFF" " and unplug it. Allow it to cool.
* Use a dry cloth to clean the external surfaces of the heater.
DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.
* Clean your heater using the above mentioned steps, then pack the heater in its
original container and store it in a cool dry place.
* This heater does not disassemble.
* The motor is factory lubricated for life, and will require no further lubrication.