Steinbach Speedpump FLAT TPX 3200 User manual

Speedpump FLAT TPFX 3200
2012_V3 page 1 of 6
Owner’s Manual
Speedpump FLAT
TPX 3200
Art. Nr. 00-41050

Speedpump FLAT TPFX 3200
2012_V3 page 2 of 6
Basic safety precautions should always be followed, including the following: Failure to follow instructions can
cause severe and/or fatal injury.
In this manual, the callout boxes, CAUTION, IMPORTANT and ADVICE have the following meanings:
This heading is used when injury or accidents may occur if the operating instructions, work instructions, work pro-
cedures, etc. are either NOT strictly adhered to, or not carried out all.
This heading is used when damage to the device may occur if the operating instructions, work instructions, work
procedures, etc. are either NOT strictly adhered to, or not carried out all.
This heading is used to call attention to special details or information.
ADVICE
IMPORTANT
CAUTION

Speedpump FLAT TPFX 3200
2012_V3 page 3 of 6
Table of Contents:
Owner’s Manual ..................................................................................................................................................... 1
1Safety Warnings............................................................................................................................................ 4
2General Information...................................................................................................................................... 4
2.1 Safety Notes ........................................................................................................................................... 4
2.2 Damage During Delivery......................................................................................................................... 4
2.3 Implied Warranty .................................................................................................................................... 4
2.4 Resultant Damages ................................................................................................................................ 4
3Troubleshooting ........................................................................................................................................... 5
Check the water lever to make sure the pump has enough water to function......................................... 5
4To reduce risk of electric shock .................................................................................................................. 5
5Save for future Reference ............................................................................................................................ 5
6Technical Specifications .............................................................................................................................. 6
7Regular maintenance will add to your pump´s life .................................................................................... 6
8Service Processing....................................................................................................................................... 6

Speedpump FLAT TPFX 3200
2012_V3 page 4 of 6
1 Safety Warnings
Read all Warnings and Cautions noted blow. Failure to do so could result in serious or fatal injury.
RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED CAN RESULT IN SERIOUS
INJURY OR DEATH. Do not block pump suction at the pump or in the pool as this can cause severe in-
jury or death.
Electrical wiring MUST be installed by a trained professional and adhere to local code and regulations.
Avoid electric shock. DO NOT USE power extension cords.
Never PLUG or UNPLUG this unit from an electrical source while standing in water.
NEVER service this unit with the electrical power cord connected.
Do NOT operate the system while the pool is being used.
KEEP CHILDREN AWAY from all electrical equipment.
NEVER ALLOW CHILDREN TO OPERATE THIS EQUIPMENT.
2 General Information
2.1 Safety Notes
Your pump was constructed and tested and left the manufacturing plant in technically operational condition. In or-
der to maintain this condition and ensure safe operation, the user should observe the notes and product infor-
mation contained in this technical handbook. If there is any indication that safe operation is no longer possible, the
device is to be disconnected from the power supply and secured against accidental use.
This is the case when:
The device has visible damage
The device no longer appears funcional
After long periods of storage in poor conditions
If the power cord or other parts of this equipment are damaged, they have to be replaced by the manufac-
turer or its service agent or a similarly qualified person in order to avoid danger.
2.2 Damage During Delivery
Your pump has been carefully and professionally packed for delivery. Please check to ensure that the package is
undamaged and that all parts are in the box. If you purchased this product on order and the product was shipped
to you, ensure that delivery is complete. Damage to product as a result of shipping is not the responsibility of the
supplier and must be immediately reported to the shipper. The shipper assumes the liability for damages during
delivery, the supplier is not responsible for it.
2.3 Implied Warranty
The manufacturer warranties safe operation and reliability only under the following conditions:
The pump is installed and operated according to the assembly and operating instructions.
Only original replacement parts are used (consumable parts do not fall under the warranty).
2.4 Resultant Damages
We cannot be responsible for damages to the product if the product is not used in accordance with the instruc-
tions provided.
These caution warnings are not intended to incorporate
all possible instances for risk and/or severe injury.

Speedpump FLAT TPFX 3200
2012_V3 page 5 of 6
3 Troubleshooting
If the pump fails to operate, check the following:
Check the circuit breaker, or try a different outlet to maker sure the pump is getting electrical power.
Check the pump discharge and tubing for kinks and obstructions.
Algae buildup can be flushed out with a garden hose.
Remove the pump front cover & plate to access the impeller area.
Turn the rotor to ensure it is not broken or jammed.
Always disconnect from electrical outlet before handing the pump.
If the pump gurgles, spews, or “ burps ":
Check the water lever to make sure the pump has enough water to function.
Obtaining a desired water lever check the water lever daily. In the first week to measure the water loss due
to Evaporation, refill the water when needed.
If abnormal noise is heard during operation (with water):
Remove pump front cover & plate.
Use hand to grip the impeller, gently pull the impeller/rotor assembly out of the pump housing.
Rinse the impeller/rotor assembly and the cavity with clean water to remove any debris. If breakage or sur-
face damage is found on the assembly, contact your distributor for part replacement.
4 To reduce risk of electric shock
Always unplug the pump from the electrical outlet before cleaing and handing.
Use with clean water ONLY. Do not place in other liquid.
The pump is supplied with a grounding conductor and a grounding type attachment plug. To reduce the risk of
electric shock, connect only to a properly grounded outlet.
Do not connect to any voltage other than tha shown on the pump.
Do not use water above 30 °C.
Ensure that the electrical cord loops below the electrical out to from a “drip loop”. This will prevent water
from running down the cord into the electrical outlet.
5 Save for future Reference
Read all instructions carefully before operating.
Connect the pump with proper voltage as indicated on the pump label. Always keep the cord away from
high temperature and fire.
IMPORTANT
CAUTION