STEINEL IS 360 W User manual

Installation Instructions
Ceiling Mount Outdoor
Occupancy Sensor
Consignes d’installation
Détecteur de présence
Montage sur plafond à l’extérieur
IS 360 W
IS 360 B
English
Made in
Romania
Français
RoHS
Compliant

2
www.steinel.net [phone]
Product Overview
120V
60Hz PIR
IP54 360°
Ceiling
mount
Applications
• Exterior: entryways, carports,
balconies, building soffits
• Interior: corridors, vestibules,
garages
Intended uses
• Suitable for automatic switching
of lights
• NOT suitable for alarm systems
In this package
• IS 360 sensor
• Accessory pack (2 fastening
screws, 2 anchors, 2 rubber
plugs, 3 wire nuts, 2 lens
shrouds)
• Installation instructions
Needed for installation
• For exterior installation:
1 NEMA watertight round
4-inch junction box
• For interior installation:
1 octagon 4-inch junction box
Note: mounting screw holes are
3.5” apart
IS 360 Installation Overview
Environmental considerations
• Weather can affect operation
of the sensor. Strong gusts of
wind, snow, rain and hail can
cause switching errors, since the
sudden temperature changes
cannot be distinguished from
heat sources.
WARNING
• Turn power off at the circuit breaker before installing the sensor
• Sensor must be installed and used in accordance with appropriate
electrical codes and regulations
• Installation by a qualified electrician is recommended

3
www.steinel.net [phone]
Voltage 120 VAC, 60 Hz
Load rating 0-600 watt Tungsten
0-300 watt Ballast
Time delay 10 sec to 15 min
Light level .2 - 200 footcandles
2 - 2000 lux
Coverage 360°, up to 40
foot reach
Environment Rated IP54 raintight
-4°F to +122°F
-20° C to +50°C
Dimensions 3.9 x 4.7 x 4.7 in
100 x 120 x 120 mm
5 year warranty
UL Listed, CSA Approved,
RoHS Compliant
SpecificationsProduct description
The STEINEL IS 360 occupancy
sensor automatically turns lights
ON when presence is detected and
OFF when a space is left vacant,
enhancing security, convenience
and energy savings. The sensors are
raintight for safe, reliable operation
indoors and out.
40 ft 40 ft
40 ft
40 ft 40 ft
Mounting plate
Sensor housing
Decorative ring
(adjustments beneath)
Housing cover
Coverage shroud
Detection lens
1 4
2 5
3 6
1
4
5
6
2
3

4
www.steinel.net [phone]
Mounting
Fastening screw
Placement guidelines
• Intended for surface mounting
under soffit (exterior) or on
ceiling (interior)
• Ideal outdoor placement for the
IS 360 is under an overhang
• Detection lens must have a clear,
unobstructed view of detection
area
• Ideal mounting height is
8-12 feet
• Backout the 2 fastening screws;
separate sensor housing from
mounting plate.
• Insert the two rubber plugs into the
mounting plate.
• Place the sensor wires through
the knockout in the center of
the mounting plate and connect
electrical wires (see Wiring).
• Align mounting plate with junction
box and secure with j-box screws.
• Realign mounting plate to sensor
housing; secure with fastening
screws.
• Reapply and engage the housing
cover.
(Note: The device housing is not
suitable for field wiring termination.)
Housing cover
Decorative ring
Mounting plate
Sensor housing
Junction box
1
2
4
3
Installation
Ensure use of the correct enclosure
and confirm power is off at the
circuit breaker.
• Remove housing cover. Press
the two indentations on side
of housing cover, turn counter-
clockwise and pull.

5
www.steinel.net [phone]
Wiring
L
O
A
D
LINE (BLACK)
NEUTRAL
Local OFF
Switch (optional)
HOT
NEUTRAL (WHITE)
LOAD (RED)
When installing, make sure power has
been switched off at the breaker and
check that the circuit is dead with a
voltage tester. The leads consist of
three wires:
Black L IN = hot wire
Red L OUT = switched hot wire for
fixture
L
O
A
D
L
O
A
D
LINE (BLACK)
NEUTRAL
Local OFF
Switch (optional)
HOT
NEUTRAL (WHITE) LOAD (RED) LINE (BLACK) NEUTRAL (WHITE) LOAD (RED)
White N = neutral wire. Connect N
(white) with the neutral wire (usually
white)
Connect L OUT (red) with the hot wire
of the fixture (usually black.) Connect
L (black) with the hot wire of the
supply lead (usually black.)