STI Stopper Station SS-2008 Series User manual

Stopper®Station Series SS-2008
Push Button Pneumatic Timer Button
neumatic Timer Models
SS-2008 Red
SS-2108 Green
SS-2208 Yellow
SS-2308 White
SS-2408 Blue
ALL ODELS CO E WITH A
COLOR ATCHED SURFACE
OUNT BACKBOX
ADA
for operation
We protect the things that protect you.®

- 2 -
This push button has been tested according to UL38 and UL2017. anual fire
alarm stations are listed in UL category UNIU and non-fire alarm initiating devices
are listed in UL category UEHX. It is important to read, understand and follow all
instructions provided with this product. It is the installer’s responsibility to
comply with NFPA72 and 101, NEC, mounting specifications according to ADA
and other applicable fire and electrical codes. After installation and testing are
complete, provide a copy of this manual to all personnel responsible for testing
and maintenance of this product. To avoid electrical shock, DO NOT attempt to
install this product when power is on.
* For access control installations, power for the SS-2008 must be supplied by a
power source Listed to UL294. When used for access control, this device shall be
used as a part of an access controlled egress door system. It is up to the local
AHJ to allow use of this device in place of an automatic sensor. For higher
security installations, lower time limits should be used.
L’essai de ce bouton-poussoir a été réalisé selon UL38 et UL2017. Les avertis-
seurs d’alerte d’incendie manuels sont répertoriés sous la catégorie UL UNIU
tandis que les dispositifs de déclenchement d’alertes non incendie sont réper-
toriés sous la catégorie UL UEHX. Il est important de lire, de comprendre et de
suivre toutes les instructions fournies avec ce produit. Il incombe à l’installateur
de se conformer aux normes NFPA72 et 101, NEC, aux spécifications de mon-
tage selon l’ADA et aux autres codes de prévention des incendies et de l’élec-
tricité en vigueur. Pour éviter un choc électrique, NE tentez PAS d’installer ce
produit lorsqu’il est sous tension. Une fois l’installation et les essais terminés,
vous devez fournir une copie de ce manuel à l’ensemble du personnel chargé
de l’essai et de l’entretien de ce produit.
* Pour les installations de contrôle d’accès, l’alimentation SS-2008 doit être
fournie par une source homologuée UL294. Lorsque cet appareil est utilisé aux
fins de contrôle d’accès, il doit faire partie d’un système de porte de sortie à
accès contrôlé. Il incombe donc à l’AHJ local d’autoriser l’utilisation de cet
appareil au lieu d’un capteur automatique. Pour les installations de sécurité plus
renforcée, des délais inférieurs doivent être utilisés.

Installation and Service Instructions
STOPPER®STATION SERIES SS-2008
PUSH BUTTON PNEUMATIC TIMER
SAFETY NOTICE TO INSTALLERS AND USERS
I. GENERAL
roduct Dimensions See page 3
Contact Rating One set NO and one set NC
Rated at 10 A P @ 240 VAC
Recognized component listing is
1,000,000 cycles
UL File #UL57255 Operating Temperature of button 15°-120°F (-9°to +49°C
II. CONTENTS LIST
QTY. DESCRI TION
1Push Button Housing Assembly
1 19001 Allen Head Screw #8-32 x 3/8 in.
1 19015 Allen Wrench 3/32 in.
4 19068 #6 x 5/8 in. hi-low screw
219060 Screw #6-32 x 1 in.
1 19021 Ground Screw
4 19039 #6 x 1 1/4 in. SS S S
4 19018 Plastic Screw Anchor
1 71100A Surface Backbox
III. INSTRUCTIONS
Product Dimensions .......................................................................... Page 3
Front Housing Removal .................................................................... Page 3
Backbox Preparation ........................................................................ Page 4
Switch Contact Diagram.................................................................... Page 5
Switch Data........................................................................................ Page 5
Installation ........................................................................................ Page 6
Warranty .......................................................................................... Page 7
- 3 -

IEW SHOWING FRONT HOUSING REMO AL
- 4 -
PRODUCT DIMENSIONS
19011 SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3
BUTTON AND SWITCH ASSEMBLY
19015 WRENCH
(1) PROVIDED
10271 SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
QTY. PART No. NAME
P
4
1 1
1 2
1
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
IS NOT USED
1
1.62 in.
(41mm)
3.25 in. (82mm)
1.58 in.
(40mm)
1.375 in.
(35mm)
PUSH
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
8 x 1
A
IS NOT USED
1
6-32 x 1. 00
1
4.87 in.
(124mm)

J
J
J
J
HSWITCH BACKPLATE
MOUNTING HOLES
BOX MUST BE INSTALLED WITH
ARROWS POINTING UPWARD
THESE HOLES MUST BE
DRILLED OUT USING A
5/32 in. DRILL BIT
H
J
OUNTING HOLESM
T
CKPLA
ATE
ACH BWITS
H
J
ALLED WITHTT BE INSUSX MOB
TE
ALLED WITH
J
J
WS POINTING UPWOARR
ALLED WITHTT BE INSUSX MOB
5/32 in. DRILL BIT
DRILLED OUT USING A
T BEUSTHESE HOLES M
H
ARDWS POINTING UPW
ALLED WITH
5/32 in. DRILL BIT
DRILLED OUT USING A
T BE
BACKBOX PREPARATION
(NOT INCLUDED WITH FLUSH MOUNT COVERS)
FIELD DRILLING FOR CONDUIT ENTRY IS
REQUIRED. LOCATIONS SHOWN ALSO
A LY TO O OSITE, ARALLEL SIDES.
- 5 -
J
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
D
S NEEDEDDRILL A
ONDUIT FITC
OP AND BT
DRILL POINT L
S NEEDED
.TINGSONDUIT FIT
OR 1/2 in.M FOTTOOP AND B
VIDEDOTIONS PROCADRILL POINT L

CONTACT DIAGRAM
SWITCH INFORMATION
- 6 -
CONTACTS
One set NO and one set NC
LEAD WIRE COLORS
IN ARENTHESIS.
QTY. PART No. NAME
P
4
1 1
1 2
1
12
1
SETTING – 25 TO 45 SECONDS
F
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
8 x 1
A
IS NOT USED
1
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
QTY. PART No. NAME
P
3
4
1 1
1 2
1
6-32 x 1. 00
1
SETTING – 25 TO 45 SECONDS
F
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
IS NOT USED
1
6-32 x 1. 00
1
NC
NO
NC
NO
BUTTON ACTIVATED
M
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.

WITHOUT PRO IDED
SURFACE BACKBOX
- 7 -
WITH PRO IDED
SURFACE
BACKBOX
INSTALLATION
QTY. PART No. NAME
P
4
1 1
1 2
1
8 x 1
A
3.5mm x 13mm
T
QTY. PART No. NAME
P
3
4
1 1
1 2
1
12
9
IS NOT USED
1
TYPICAL FLUSH MOUNT
GANG BOX
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
19021 GROUND SCREW
BUTTON AND SWITCH ASSEMBLY
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
71100A-COLOR SURFACE BOX
19018 ANCHOR
(4) PROVIDED
DRILL (4) 3/16 in.
DIA HOLES
J
(4) PR
19018 ANCHOR
DIA HOLES
DRILL (4) 3/16 in.
VIDEDO(4) PR
19018 ANCHOR
XOCE BAOR SURFOLC-71100A
VIDEDO(4) PR
1/4 in.-19039 SCREW #6 x 1
SEMBLSCH AWITON AND STBUT
OUND SCREW19021 GR
Y
MBL
LY
VIDEDO(2) PR
19060 SCREW #6
VIDED
32 x 1 in.-19060 SCREW #6
INSTALLATION NOTE
ADA mounting compliance
requires the operable part of
the initiating device shall not
be less than 1.1m (3 1/2 ft.) or
greater than 1.37m (4 1/2 ft.)
above finished floor service.

2306 Airport Rd • Waterford, MI 48327
hone: 248-673-9898 • Fax: [phone]
800-888-4STI (4784) • www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G ipers Road • ark Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-europe.com
2008 A-IS
02/04
Warranty
Three year guarantee against breakage of polycarbonate in normal use (one
year on electro mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.