STI-7560AC ENCLOSURE MOUNTING INSTRUCTIONS
All specifications and information shown were current as of publication and are subject to change without notice.
7560AC OCT2010
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Web: www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: +44 (0)1527 520 999 • Fax: +44 (0)1527 501 999
NOTE:
If mounting to brick, block or concrete wall, drill 5/8” diameter
holes 2” deep and insert lag shields.
If mounting to wood wall or wood stud, drill 9/32” diameter holes
1-1/2” deep.
INSTALLATION INSTRUCTIONS
1. Using needle-nose pliers remove both hinge pin snap rings.
2. Push out or lift out hinge pins and remove door.
3. Place enclosure on wall and mark top right hole position onto
wall. Set enclosure aside.
4. Drill hole according to note above.
5. Insert lag screw into sealing washer. Place enclosure on wall and
insert lag screw with sealing washer through enclosure and into
drilled hole. Finger tighten only.
6. Allow enclosure to pivot and hang from lag screw.
7. Set a level on top of enclosure and level enclosure. Mark the
remaining three mounting holes onto wall.
8. Allow enclosure to pivot and hang from lag screw and drill the
remaining three holes.
9. Insert the remaining three lag screws with sealing washers
through enclosure into wall and tighten all (4) lag screws.
8.79 in.
(223mm)
7.5 in.
(191mm)
15.75 in.
(400mm)
6.35 in.
(161mm)
24 in.
(610mm)
36 in.
(914mm)
8.79 in.
(223mm)
7.5 in.
(191mm)
15.75 in.
(400mm)
6.35 in.
(161mm)
24 in.
(610mm)
36 in.
(914mm)
REMOVE THE (4) SCREWS AND
FRONT COVER TO OBTAIN ACCESS
TO TEMPERATURE CONTROLS.
(SEE INSTRUCTION MANUAL FOR DETAILS)
FRONT COVER
INLET AIR FILTER
REMOVE TO CLEAN.
(SEE INSTRUCTION MANUAL)
TEMPERATRUE
CONTROLS
MOUNTING A/C UNIT TO ENCLOSURE
After Enclosure has been mounted to wall
A/C Unit can be mounted to Enclosure.
1. Read and endersatnd Instruction Manual before mounting and
opperating A/C Unit.
2. Install gasket provided on to A/C Unit.
3. Insert power cord and wires through top cutout in Enclosure.
4. Mount A/C Unit to Enclosure by resting EZ mount tabs on bottom cutout edge.
This will hold A/C Unit in place while bolts are inserted.
5. Insert the (4) 1/4 - 20 x 3/4 in. bolts with lock washers. (Make sure the threads
of all (4) bolts have engaged with the A/C Unit before tightening.)
6. Tighten the 4 bolts evenly.
7. Replace Door, Hinge Pins and Hinge Pin Snap Rings.
AENCLOSURE MOUNTING INSTRUCTIONS
NOTES:
If mounting to brick, block or concrete walls...
Drill 5/8 dia. holes 2 in. deep and insert lag sheilds.
If mounting to wood walls or wood studs...
Drill 9/32 dia. holes 1-1/2 in. deep.
1. Using needle-nose pliers remove both Hinge Pin Snap Rings.
2. Push out or lift out Hinge Pins and remove door.
3. Place Enclosure on wall and mark top right hole position onto wall.
Set Enclosure aside.
4. Drill hole according to Notes above.
5. Insert Lag Screw into Sealing Washer. Place Enclosure on wall and insert
Lag Screw with Sealing Washer through Enclosure and into drilled hole.
Finger tighten only.
6. Allow Enclosure to pivot and hang from Lag Screw.
7. Set a level on top of Enclosure and level Enclosure. Mark the remaining
three mounting holes onto wall.
8. Allow Enclosure to pivot and hang from Lag Screw and drill the remaining
three holes.
9. Insert the remaining three Lag Screws with Sealing Washers through Enclosure
into wall and tighten all (4) Lag Screws.
“EZ” MOUNT TABS
DETAIL A
BOTTOM CUTOUT EDGE
A
A/C UNIT
INSTALL GASKET PROVIDED
ENCLOSURE SHOWN WITH DOOR REMOVED
1/4 - 30 x 3/4 in. BOLT
(4) PROVIDED
LOCK WASHER
(4) PROVIDED
3/8 LAG SHIELD
(4) PROVIDED
SEALING WASHER
(4) PROVIDED
3/8 x 1-1/2 LAG SCREW
(4) PROVIDED
HING PIN SNAP RING
(ONE ON EACH HING PIN)
A
8.79 in.
(223mm)
7.5 in.
(191mm)
15.75 in.
(400mm)
6.35 in.
(161mm)
24 in.
(610mm)
36 in.
(914mm)
3/8 LAG SHIELD
(4) PROVIDED
SEALING WASHER
(4) PROVIDED
3/8 x 1-1/2 LAG SCREW
(4) PROVIDED
HINGE PIN SNAP RING
(ONE ON EACH HINGE PIN)
A
DETAIL A
“EZ” MOUNT TABS
DETAIL A
BOTTOM
CUTOUT EDGE
A
A/C UNIT
INSTALL GASKET PROVIDED
ENCLOSURE SHOWN
WITH DOOR REMOVED
1/4 - 20 x 3/4 in. BOLT
(4) PROVIDED
LOCK WASHER
(4) PROVIDED
REMOVE THE (4) SCREWS AND
FRONT COVER TO OBTAIN ACCESS
TO TEMPERATURE CONTROLS.
(SEE INSTRUCTION MANUAL FOR DETAILS)
FRONT COVER
INLET AIR FILTER
REMOVE TO CLEAN.
(SEE INSTRUCTION MANUAL)
TEMPERATURE
CONTROLS
Three year warranty or a one year limited warranty (from
date of purchase) on most products. See website for details.
Electronic warranty form at www.sti-usa.com/wc14.
