STI STI-7532 User manual

backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at
view
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
of cabinet. Select at least two
optional mounting holes. Mark and drill 3/16 in.
diameter holes and inst
mounting plate and the siren backplate. Nex
drive the (2) alarm mounting screws into the
previous inst
the terminal sw
screws and provided tool.
19033 ANCHOR
(4) PROVIDED
EMERGENCYUSEONLY
STI-7532 - KEY LOCK
STI-7533 & STI-7533AED - THUMB LOCK
STOP
07530WR
ADJUSTABLE WIRE SHELF
INCLUDED WITH STI-7533AED
0
MOUNTING
TAB SLOTS
04875 MOUNTING PLATE
19002 SCREW
#8-32 x 3/8 in.
(4) PROVIDED
OPTIONAL SHELF
MOUNTING POSITION
06298
MOUNTING TABS
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
07530 CABINET
ASSEMBLY
6297530
GASKET
-
-
INSTALLATI N F STI-7532, STI-7533 & STI-7533AED PR TECTIVE CABINET
A
9 VOLT ALKALINE BATTERY
06201 STOP ALARM COVER
19016 TAMPERPROOF TOOL
(1) PROVIDED
19032 KEY (2) PROVIDED
19011 SCREW - TAMPERPROOF
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
19018 ANCHOR
(2) PROVIDED
MAGNETIC CONTACT
REED SWITCH
ALARM MOUNTING PLATE
06202 BACKPLATE
STOP
EMERGENCY USEONLY
Safety Technology International, Inc. • 2306 Airport Rd. • Waterford, Michigan 48327-1209 • 800-888-4784 • Fax: 248-673-1246 • Web: www.sti-usa.com • Email: [email protected]
INSTALLATI N F CABINET
1. Insert the (4) 06298 mounting tabs fully into
backbox mounting tab slots. Use rubber mallet
if necessary.
2. After selecting a suitable location, place
cabinet in closed position, against the wall.
ark and drill (4) 1/4 in. diameter holes.
Insert the (4) 19033 anchors.
3. Select one of the two shelf mounting locations,
install shelf. Close and lock cabinet.
4. Place cabinet in position making sure the (2)
switch wires are not pinched between the wall
and cabinet. Drive in the (4) screws. Cabinet is
now secure.
1. Place the alarm mounting plate on the top
center of cabinet. Select at least two of the
four optional mounting holes. ark and drill
3/16 in. holes and install the 19018 anchors.
2. Fish the magnetic switch wires through the
alarm mounting plate and the siren backplate
(View A). Next, drive the two alarm mounting
screws into the previous installed anchors.
3. Install the two magnetic switch wires following
the terminal switch diagram (View B).
4. Install the alarm cover using the (2)
tamperproof screws and provided tool.
INSTALLATI N F ALARM ASSEMBLY
EMERGENCY USE ONLY
FRONT
5.375 in.
(137mm)
R.H. SIDE
backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at
view Close and lock cabinet.
4
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
of cabinet. Select at least two
optional mounting holes. Mark and drill 3/16 in.
diameter holes and inst
mounting plate and the siren backplate. Nex
drive the (2) alarm mounting screws into the
previous inst
the terminal sw
screws and provided tool.
1
STOP
23 in.
(584mm)
12.2 in.
(310mm)
14.2 in.
(360mm)
2.25 in.
(57mm)
6.44 in.
(164mm)
S
-
v
moun
orien
as sho
t
(4) 1/4 in. diame
and c
(Do no
ALARM MOUNTING PLATE
CABINET
WIRE ACCESS HOLE
ROUTE THE 2 SWITCH WIRES
THROUGH THE HOLE AS SHOWN
OPTIONAL MOUNTING
HOLES (4)
v
moun
orien
as sho
t
(4) 1/4 in. diame
and c
W
(Do no
VIEW A

SWITCH SETTINGS
Volume - High (105 dB) at 1 ft. ON*
Volume - Low (95 dB) at 1 ft. OFF
Duration - 30 Second Alarm OFF OFF
Duration - 180 Second Alarm OFF ON
Duration - Continuous Alarm ON* OFF*
Duration - Annunciator ode ON ON
Trip - Immediate OFF*
Trip - 15 Second Delay ON
Arming - Immediate ON*
Arming - 15 Second Delay OFF
FEATURE JP2 JP3 JP4 JP5 JP7
*Factory Settings
Note: Slide black lever to desired ON/OFF
position as labeled on circuit board.
Printed in USA
Safety Technology International, Inc.
2306 Airport Road • Waterford, ichigan 48327-1209
Phone: 248-673-9898 • Toll Free: 800-888-4784
Fax: 248-673-1246 • www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
CIRCUIT B ARD SET-UP
Nex
JP5
JP2
JP4
JP3
JP7
ALARM VOLUME SWITCH
TRIP DELAY SWITCH
ARMING SWITCH
(FACTORY DEFAULT SETTINGS)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
ALARM CIRCUIT BOARD SET-UP
ALARM
DURATION
SWITCH
TERMINAL BLOCK
D
(
-
-
-
Inst. Sht. 7532, 7533, &7533AED, NOV2010
WARNINGS
WARRANTY INF RMATI N
SPECIFICATI NS
All units are recommended for indoor use. Unit must be tested periodically to verify the life of battery. STI recommends you change the battery twice a year. Duracell
N 1604 or equivalent recommended. Installer may need to purchase a simple audio-meter, typically available at your local electronics store, to measure the sound
in areas where the alarm is expected to be heard during normal noise environment. Results from this test may prove it beneficial to purchase an additional alarm.
When purchasing a remote unit (STI-6403) you will need to periodically test the connections to make sure audibles function at a sound level to alert staff. aximum of
three STI-6403 may be used in parallel. All specifications and information shown are current as of publication and subject to change without notice.
Lifetime guarantee against breakage of polycarbonate housing (one year on electronics).
9 VDC Alkaline or 9V-24VDC wired
Class II UL Listed transformer
Horn Volume at 1 ft. 95 dB low / 105 dB high
Relay Output Form C Dry Contacts 0-30 VDC or VAC, 1 Amp
Stand by Current 10uA
Alarm Current 130mA at 95 dB / 200mA at 105 dB
Power Source
Polycarbonate Alarm Cover:
Dimensions 5.375” W x 5.375” H x 2 “ D (137mm x 137mm x 51mm)
Flammability: UL94 V-2
Wall Thickness: 0.12 in (3.05mm)
Alarm Electronics
backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at
view
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
Mark and drill 3/16 in.
B
FROM MAGNETIC
CONTACT SWITCH
-
-
-
backbox mounting tab slots. Use rubber
mallet if necessa
in closed position, against the wall. Mark and
drill (4) 1/4 in. diameter holes. Insert the (4)
19033 anchors.
3
inst
through the access hole at See
view Close and lock cabinet.
4
wires are not pinched between the wall and cabinet.
Drive in the (4) screws. Cabinet is now secure.
I
Mark and drill 3/16 in.
NCCOM NOGD V+ RS1 RS2 KEYSW
VIEW B
TERMINAL BLOCK WIRING CONNECTIONS
FORM C
DRY
CONTACTS
REMOTE
POWER
INPUT
9-24 VDC
KEY SWITCH
TERMINALS
MAGNETIC CONTACTTIC
REED SWITCH
JUMPER
-
-
-
VIEW B
This manual suits for next models
2
Other STI Enclosure manuals