STIEBEL ELTRON SBP 100 classic Instruction Manual

BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
BEDIENING EN INSTALLATIE
OBSLUHA A INSTALACE
OBSŁUGA I INSTALACJA
HASZNÁLATI ÉS TELEPÍTÉSI ÚTMUTATÓ
BETJENING OG INSTALLATION
Pufferspeicher| Buffer cylinder| Ballon tampon| Buffervat| Akumulační
zásobník| Zbiornik buforowy| Puffertároló| Bufferbeholder
» SBP 100 classic

8| SBP 100 classic www.stiebel-eltron.com
CONTENTS | OPERATION
General information
1.1 Safety instructions
1.1.1 Structure of safety instructions
!KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol Type of risk
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-seri-
ous or minor injury.
1.2 Other symbols in this documentation
Note General information is identified by the adjacent symbol.
 Read these texts carefully.
Symbol Meaning
Material losses
(appliance damage, consequential losses and environmen-
tal pollution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Information on the appliance
Connections
Symbol Meaning
Supply/ Inlet/ Flow
Drain/ Outlet/ Return
Heat pump
Central heating
!
OPERATION
1. General information �����������������������������������������8
1.1 Safety instructions����������������������������������������������� 8
1.2 Other symbols in this documentation ����������������������� 8
1.3 Information on the appliance ��������������������������������� 8
1.4 Units of measurement ������������������������������������������ 9
2. Safety����������������������������������������������������������9
2.1 Intended use������������������������������������������������������ 9
3. Appliance description ���������������������������������������9
4. Troubleshooting ����������������������������������������������9
INSTALLATION
5. Safety����������������������������������������������������������9
5.1 General safety instructions ������������������������������������ 9
5.2 Instructions, standards and regulations �������������������� 9
6. Appliance description ���������������������������������������9
6.1 Standard delivery������������������������������������������������ 9
7. Preparations������������������������������������������������ 10
7.1 Installation site�������������������������������������������������� 10
8. Installation�������������������������������������������������� 10
8.1 Positioning the equipment������������������������������������ 10
8.2 Heating water connection������������������������������������� 10
9. Commissioning ��������������������������������������������� 10
9.1 Initial start-up��������������������������������������������������� 10
9.2 Recommissioning����������������������������������������������� 10
10. Shutdown ��������������������������������������������������� 10
11. Maintenance ������������������������������������������������ 10
11.1 Draining the appliance ���������������������������������������� 10
12. Specification ������������������������������������������������ 11
12.1 Dimensions and connections��������������������������������� 11
12.2 Details on energy consumption������������������������������ 11
12.3 Data table �������������������������������������������������������� 11
GUARANTEE
ENVIRONMENT AND RECYCLING
OPERATION
1. General information
The chapter "Operation" is intended for appliance users and qual-
ified contractors.
The chapter "Installation" is intended for qualified contractors.
Note Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.

ENGLISH
www.stiebel-eltron.com SBP 100 classic | 9
OPERATION | INSTALLATION
Safety
1.4 Units of measurement
Note All measurements are given in mm unless stated oth-
erwise.
2. Safety
2.1 Intended use
This appliance is designed to extend the operating time of the heat
generator and to bridge power-OFF periods. The heat pump buffer
cylinder also provides hydraulic separation of the flow rates in the
heat pump circuit and the heating circuit.
Observation of these instructions and of instructions for any ac-
cessories and other system components used is also part of the
correct use of this appliance.
Any other use beyond that described shall be deemed inappro-
priate. Using the appliance for heating fluids other than water
or for water supplemented with chemicals, such as brine, is also
deemed inappropriate.
3. Appliance description
The steel cylinder with directly applied foam insulation is equipped
with a protective cover, connections for ventilation and draining,
and a sensor pipe. The hydraulic connections are routed through
the top.
4. Troubleshooting
Call your qualified contractor.
To facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000):
000000-0000-000000
Made in Germany
D0000056158
INSTALLATION
5. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
5.1 General safety instructions
We guarantee trouble-free function and operational reliability only
if original accessories and spare parts intended for the appliance
are used.
5.2 Instructions, standards and regulations
Note Observe all applicable national and regional regulations
and instructions.
6. Appliance description
6.1 Standard delivery
The following are delivered with the appliance:
- 3adjustable feet

10 | SBP 100 classic www.stiebel-eltron.com
INSTALLATION
Preparations
7. Preparations
7.1 Installation site
 Always install the appliance in a room free from the risk of
frost.
 Ensure the floor has sufficient load bearing capacity and
evenness (see chapter "Specification/ Data table").
 Observe the room height and height when tilted (see chapter
"Specification/ Data table").
Minimum clearances
≥100
≥100
≥400
≥100
≥800
D0000056166
8. Installation
8.1 Positioning the equipment
Use the adjustable feet provided to compensate for any uneven-
ness in the floor.
 Undo the 3screws from the non-returnable pallet.
 Tilt the appliance and screw the 3adjustable feet provided
into the appliance.
 Lift the appliance off the pallet.
 When installing, observe minimum clearances (see chapter
"Preparations/ Installation site").
8.2 Heating water connection
!Material losses
Carry out all water connection and installation work in
accordance with regulations.
Observe the heat pump operating and installation instructions
when making the heating water connection.
Oxygen diffusion
!Material losses
Avoid open heating systems and plastic pipes in under-
floor heating systems which are permeable to oxygen.
In underfloor heating systems with plastic pipes that are per-
meable to oxygen and in open vented heating systems, oxygen
diffusion may lead to corrosion on the steel components of the
heating system (e.g. on the indirect coil of the DHW cylinder, on
buffer cylinders, steel heating elements or steel pipes).
!Material losses
The products of corrosion (e.g. rusty sludge) can settle in
the heating system components and can result in a lower
output or fault shutdowns due to reduced cross-sections.
9. Commissioning
9.1 Initial start-up
 Fill and bleed the appliance (see chapter "Specification/ Di-
mensions and connections").
 Carry out a tightness check.
9.1.1 Appliance handover
 Explain the function of the appliance to users and familiarise
them with its operation.
 Make the user aware of potential dangers, especially the risk
of scalding.
 Hand over these instructions.
9.2 Recommissioning
See chapter "Commissioning/ Initial start-up".
10. Shutdown
 Drain the appliance. See chapter "Maintenance/ Draining the
appliance".
11. Maintenance
No special maintenance is required for the appliance. A regular
visual check is sufficient.
11.1 Draining the appliance
WARNING Burns Hot water may escape during draining.
If the appliance needs to be drained for maintenance or to protect
the whole installation when there is a risk of frost, proceed as
follows:
 Drain the appliance using the appliance drain connection
(see chapter "Specification/ Dimensions and connections").

ENGLISH
www.stiebel-eltron.com SBP 100 classic | 11
INSTALLATION | GUARANTEE | ENVIRONMENT AND RECYCLING
Specication
GUARANTEE
ENVIRONMENT AND RECYCLING
12. Specification
12.1 Dimensions and connections
10-30
877
510 140
265
233
e03
d04
d03
e04
d46
h02
d47
D0000056070
SBP 100 classic
d03 Heat pump flow optional Male thread G 1 1/4
d04 Heat pump return optional Male thread G 1 1/4
e03 Heating flow optional Male thread G 1 1/4
e04 Heating return optional Male thread G 1 1/4
d46 Ventilation
d47 Drain Female thread G 1/2
h02 Sensor heat pump return Diameter mm 14
Optional connections
D0000056167D0000056168
Appliance sectional view
e03
d03
e04
d04
h02
d47
d46
D0000056071
12.2 Details on energy consumption
The product data complies with EU regulations relating to the
Directive on the ecological design of energy related products (ErP).
SBP 100 classic
235200
Manufacturer STIEBEL ELTRON
Energy efficiency class C
Standby losses W52
Cylinder capacity l99
12.3 Data table
SBP 100 classic
235200
Hydraulic data
Nominal capacity l 100
Application limits
Max. permissible pressure MPa 0.3
Test pressure MPa 0.4
Max. permissible temperature °C 95
Energy data
Standby energy consumption/24 h at 65 °C kWh 1.25
Energy efficiency class C
Dimensions
Height mm 877
Diameter mm 510
Height when tilted mm 968
Weights
Weight, full kg 120
Weight, empty kg 21
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.



Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [email protected]
Kundendienst Tel. [phone] | Fax [phone] | [email protected]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [email protected]
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van ver
g
issin
g
en en technische wi
j
zi
g
in
g
en! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian
y
techniczne i
ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések
j
o
g
át
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Ch
y
b
y
a
technické zmeny sú vyhradené! Stand 9046
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne VIC 3207
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Eferdinger Str. 73 | 4600 Wels
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[email protected]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[email protected]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron-usa.com
A 320031-38887-9060
4<AMHCMO=caadbe>