STIEBEL ELTRON SNU 5 SL antitropf comfort Specification sheet

BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
GEBRUIK EN INSTALLATIE
OBSLUHA A INSTALACE
OBSŁUGA I INSTALACJA
HASZNÁLATI ÉS TELEPÍTÉSI ÚTMUTATÓ
ЭКСПЛУАТАЦИЯ И МОНТАЖ
Offener (druckloser) Warmwasser-Kleinspeicher | Open vented (non-pressurised)
small water heater | Mini-ballon d’eau chaude à écoulement libre | Open
(drukloze), kleine warmwaterboiler | Malý beztlakový zásobník teplé vody |
Otwarty (bezciśnieniowy) mały pojemnościowy ogrzewacz wody | Nyitott rendszerű
(nyomásmentes) kisméretű melegvíztároló | Открытый (безнапорный) компактный
накопительный водонагреватель
» SNU 5 SL antitropf comfort
» SNU 5 SLi antitropf comfort
antitropf comfort
85
°C
35
55
65
Eco
1300 726 211
https://1stchoicehotwater.com.au

OPERATION
General information
14 | SNU 5 www.stiebel-eltron.com
OPERATION
1. General information
The chapters "Special Information" and "Operation" are intended
for both the user and qualified contractors.
The chapter "Installation" is intended for qualified contractors.
Note Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
!KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol Type of risk
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-seri-
ous or minor injury.
1.2 Other symbols in this documentation
Note General information is identified by the symbol shown
on the left.
 Read these texts carefully.
Symbol Meaning
Material losses
(appliance damage, consequential losses and environmen-
tal pollution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Units of measurement
Note All measurements are given in mm unless stated oth-
erwise.
2. Safety
2.1 Intended use
This open vented (non-pressurised) appliance is designed for heat-
ing domestic hot water. The appliance can supply one draw-off
point.
This appliance is intended for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-do-
mestic environment, e.g. in a small business, as long as it is used
in the same way.
Any other use beyond that described shall be deemed inappropri-
ate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
2.2 General safety instructions
WARNING Burns There is a risk of scalding at outlet temperatures in ex-
cess of 43°C.
!WARNING Injury
The temperature selector should only be removed by a
qualified contractor.
!WARNING Injury
The appliance may be used by children aged 8 and up and
persons with reduced physical, sensory or mental capa-
bilities or a lack of experience and know-how, provided
that they are supervised or they have been instructed on
how to use the appliance safely and have understood
the resulting risks. Children must never play with the
appliance. Children must never clean the appliance or
perform user maintenance unless they are supervised.
Where children or persons with limited physical, sensory or men-
tal abilities are allowed to use this appliance, we recommend a
permanent temperature limit. A qualified contractor can set the
limit.
!Material losses
Protect the appliance and its tap against frost.
!
!

OPERATION
Appliance description
www.stiebel-eltron.com SNU 5 | 15
ENGLISH
!Material losses
Never subject the appliance to water pressure. The tap
outlet has a vent function. Scale build-up can block the
outlet and subject the appliance to pressure.
 Never seal the tap outlet.
 Only use special aerators for non-pressurised water
heaters.
 Never use a hose with aerator to extend the tap
outlet.
!Material losses
Connecting the appliance via a time switch will cause an
unintentional reset of the high limit safety cut-out.
 Never connect the appliance to the power supply via
a time switch.
2.3 CE designation
The CE designation shows that the appliance meets all essential
requirements according to the:
- Low Voltage Directive
- Electromagnetic Compatibility Directive
2.4 Test symbols
See type plate on the appliance.
3. Appliance description
The open vented (non-pressurised) appliance constantly maintains
the water content at the pre-selected temperature. The appliance
may only be installed with taps for open vented (non-pressurised)
water heaters (see chapter "Installation/ Appliance description/
Accessories").
thermostop function
The thermostop function (thermal separation) prevents the tap
becoming hot in standby mode.
Anti-drip function
The anti-drip function prevents expansion water from escaping
from the tap during heating. When water is heated, gas bubbles
are formed. The amount of gas bubbles depends on the water
quality. At temperatures >75°C the rising gas bubbles can cause
residual water to drip from the tap outlet.
Subject to design, some taps have a tendency to drip for a short
while after being closed. This dripping is caused by residual water
escaping from the tap outlet and is not linked to expansion water.
3.1 Operation
The required DHW outlet temperature can be set at the tempera-
ture selector. The heat-up indicator illuminates during the heat-up
process.
D0000047838
2
1
1 Temperature selector
2 Heat-up indicator
°C = Cold. On this setting, the appliance is protected from
frost. The tap and the water line are not protected.
Eco = Recommended energy saving setting (approx. 60°C),
minor scaling
85 = Maximum selectable temperature
Note A qualified contractor can set a temperature limit on the
appliance (see chapter "Installation/ Settings/ Setting
the temperature limit").
4. Cleaning, care and maintenance
 Never use abrasive or corrosive cleaning agents. A damp
cloth is sufficient for cleaning the appliance.
 Check the tap regularly. You can remove limescale deposits
at the outlet using commercially available descaling agents.
5. Troubleshooting
Problem Cause Remedy
The appliance does not
supply hot water.
The temperature selector
is set to “°C”.
Switch the appliance on
by turning the tempera-
ture selector.
No power to the appli-
ance.
Check the plug and the
fuses/MCBs in the fuse
box.
Water can only be drawn
at a reduced rate.
The aerator in the tap is
scaled up.
Descale / replace the
aerator.
Loud boiling noises in-
side the appliance.
The appliance is scaled
up.
Have the appliance
descaled by a qualified
contractor.
Water drips from the tap
outlet during the heat-up
process.
Frequent minimal draw-
off amounts (< 0.4l/min).
Change your draw-off
pattern (> 0.4l/min).
If you cannot remedy the fault, notify your qualified contractor.
To facilitate and speed up your request, provide the number from
the type plate (000000-0000-000000).
Typ:
Nr.: ...... - .... - ......
D0000047804
SNU 5

16 | SNU 5 www.stiebel-eltron.com
INSTALLATION
Safety
INSTALLATION
6. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
6.1 General safety instructions
We guarantee trouble-free function and operational reliability only
if original accessories and spare parts intended for the appliance
are used.
6.2 Instructions, standards and regulations
Note Observe all applicable national and regional regulations
and instructions.
7. Appliance description
The open vented (non-pressurised) appliance is only suitable for
undersink installation. The appliance is intended to supply one
draw-off point for heating cold water.
7.1 Standard delivery
Delivered with the appliance:
- Wall mounting bracket
7.2 Accessories
7.2.1 Required accessories
The following taps are available as accessories for open vented
operation:
Mixer taps
- WST, WUT
Mono lever mixer taps
- MEW, MES, MEWC
Sensor tap
- WEN
7.2.2 Further accessories
- Strainer for the "cold water inlet" connection
8. Preparations
 Flush the water line thoroughly.
Water installation
A safety valve is not required.
Taps
Sealed taps are not permitted.
 Install an open tap.
8.1 Installation site
!Material losses
Install the appliance in a room free from the risk of frost.
!Material losses
Mount the appliance on the wall. The wall must have a
sufficient load-bearing capacity.
Note The appliance is only suitable for undersink installation.
The water connections of the appliance point upwards.
Always install the appliance vertically and near the draw-off point.
820
520-570
85
°C
35
55
65
Eco
D0000033291
850
550-600
85
°C
35
55
65
Eco
D0000033294

www.stiebel-eltron.com SNU 5 | 17
ENGLISH
INSTALLATION
Installation
9. Installation
9.1 Appliance installation
 Mark out the drill holes using the installation template (see
middle part of these instructions).
 Drill the holes and insert suitable rawl plugs.
 Secure the wall mounting bracket using suitable screws.
 Hang the appliance on the wall mounting bracket.
Note Surplus cable can be stored in the cable compartment.
D0000034827
9.2 Water connection
!Material losses
Carry out all water connection and installation work in
accordance with regulations.
!Material losses
Counterhold with a suitable spanner when tightening the
fittings.
85
°C
35
55
65
Eco
com for t
D0000034825
22 19
!Material losses
The appliance may develop a leak and cease functioning.
 Never subject the appliance to water pressure.
 Never interchange the water connections.
 Set the flow rate (see tap instructions). Observe the
maximum permissible flow rate with a fully opened
tap (see chapter "Installation/ Specification/ Data
table").
Match up the colour coding on the tap water connections and the
appliance:
- R. h. side blue = "Cold water inlet"
- L. h. side red = "DHW outlet"
 Secure the water connections from the tap to the appliance.
Note Ensure that the water connections are not kinked during
installation. Prevent any tensioning during installation.
9.3 Power supply
WARNING Electrocution Carry out all electrical connection and installation work
in accordance with relevant regulations.
WARNING Electrocution Ensure the appliance can be separated from the power
supply by an isolator that disconnects all poles with at
least 3 mm contact separation.
!Material losses
The voltage specified on the type plate must match the
mains voltage.
 Observe the type plate.
The following electrical connections are permissible:
SNU 5 SL 1kW SNU 5 SLi
Connection to a freely accessible
standard socket
X X
Permanent connection to an ap-
pliance junction box with earth
conductor
X X

18 | SNU 5 www.stiebel-eltron.com
INSTALLATION
Commissioning
10. Commissioning
WARNING Electrocution Commissioning may only be carried out by a qualified
contractor in accordance with safety regulations.
10.1 Initial start-up
26�02�06�0204
 Either open the DHW valve of the tap or set the mono lever
mixer tap to "hot" until the water that flows out is free of air
bubbles.
 Insert the plug into the standard socket or set the fuse/MCB
in the fuse box.
 Select a temperature.
Note If you fail to follow the correct sequence (first water, then
power), the high limit safety cut-out will respond.
Proceed as follows:
 Fill the appliance with water.
 Briefly disconnect the appliance from the power
supply.
10.1.1 Appliance handover
 Explain the functions of the appliance to the user. Show the
user how to operate the appliance.
 Make the user aware of potential dangers, especially the risk
of scalding.
 Hand over these instructions and, if applicable, the instruc-
tions for any accessories.
10.2 Recommissioning
See chapter "Installation/ Commissioning/ Initial start-up".
11. Settings
11.1 Setting the temperature limit
85
°C
35
55
65
Eco
D0000047839
1
2
1 Temperature selector
2 Limiting ring
Placing the limiting ring behind the temperature selector allows
you to limit the setting range of the temperature selector to a
specific maximum temperature.
 Turn the temperature selector to zero (fully anti-clockwise to
"°C").
 Pull off the temperature selector and the limiting ring.
 Push the limiting ring with the required maximum setting
onto the adjusting shaft.
 Fit the temperature selector in the zero setting (°C).
12. Shutdown
 Isolate the appliance from the power supply by removing the
plug or by tripping the fuse/MCB in the fuse box.
 Drain the appliance (see chapter "Installation/ Maintenance/
Draining the appliance").
13. Troubleshooting
Problem Cause Remedy
The appliance does
not supply hot water.
The high limit safety
cut-out has responded.
Remedy the cause of the fault.
If necessary, replace the tem-
perature controller. Allow the
appliance to cool down. If you
have isolated the appliance from
the power supply, the high limit
safety cut-out will be automati-
cally reset.
The strainer is contam-
inated.
Clean/ replace the strainer in
the "cold water inlet" connec-
tion.
Loud boiling noises
inside the appliance.
The appliance is scaled
up.
Descale the appliance.
The tap drips for a
while after it has
been closed.
The residual water
is not held in the tap
outlet.
Replace the aerator in the tap
outlet or the tap.
The tap drips when
the appliance is
heating up.
An unsuitable tap is
being used, e.g. a WAT
anti-drip tap.
Replace the tap (see chapter
"Installation/ Appliance de-
scription/ Accessories").
The anti-drip function
is faulty.
Replace the appliance.

www.stiebel-eltron.com SNU 5 | 19
ENGLISH
INSTALLATION
Maintenance
14. Maintenance
WARNING Electrocution Before any work on the appliance, disconnect all poles
of the appliance from the power supply.
 Dismount the appliance for maintenance work.
14.1 Draining the appliance
WARNING Burns Hot water may escape during the draining process.
 Drain the appliance via the connector.
14.2 Opening the appliance
85
°C
35
55
65
Eco
D0000047843
 Pull off the temperature selector and the limiting ring.
 Remove the screws underneath the temperature selector.
 Open the appliance cover by lowering the bolt screws in-
wards and pivot the cover upwards, then remove it.
14.3 Descaling the appliance
!Material losses
Never treat the cylinder surface with descaling agents.
 Remove the flanged immersion heater.
 Carefully tap the heating element to remove large limescale
deposits.
 Immerse the heating element up to the flange plate in desca-
ling agent.
14.4 Cleaning the strainer
85
°C
35
55
65
Eco
D0000047841
 Detach the "cold water inlet" connection.
 Using pliers, remove the strainer from the "cold water inlet"
connection.
 Descale or replace the strainer.
14.5 Checking the earth conductor
 Pull off the temperature selector and the limiting ring.
 Check the earth conductor (in Germany, e.g. BGVA3) across
a temperature controller fixing screw and the earth conduc-
tor contact of the power cable.
14.6 Replacing the power cable
The power cable must only be replaced by a qualified electrician
with the original spare part. Alternatively, the H05VV-F3x1.0 cable
may be used.
D0000034824
 Route the power cable along the cable guide.
14.7 Positioning the temperature sensor in its
protective pipe
 When replacing the temperature controller, guide the tem-
perature sensor into its protective pipe.
 Secure the temperature sensor in place below the earthed
plug.
26�02�06�0219
185

20 | SNU 5 www.stiebel-eltron.com
INSTALLATION
Specication
15. Specification
15.1 Dimensions and connections
c06 c01
100
421
70
230
140
263
14328
D0000035039
SNU 5 SL 1 kW SNU 5 SLi
c01 Cold water Inlet Male thread G 3/8 A G 3/8 A
c06 DHW outlet Male thread G 3/8 A G 3/8 A
15.2 Wiring diagram
1/N/PE ~ 220 - 240V
LN
85�02�06�0001
15.3 Heat-up diagram
The heat-up period depends on the degree of scaling and residual
heat. For the heat-up time for a cold water supply of 10 °C and a
maximum temperature setting, see the diagram.
35 40 45 50 55 60 65 70 75 80 85
0
5
10
15
20
25
30
1
2
84�02�02�0044
x Temperature settings in °C
y Duration in min
1 1kW appliance
2 2kW appliance
15.4 Country-specific approvals and certifications
The test symbols can be seen on the type plate.
15.5 Extreme operating and fault conditions
In the case of faults, a peak temperature up to 100 °C may briefly
occur in the system.

www.stiebel-eltron.com SNU 5 | 21
ENGLISH
INSTALLATION
Specication
15.6 Data table
SNU 5 SL 1 kW SNU 5 SLi SNU 5 SLi
221116 221121 229467
Hydraulic data
Nominal capacity l 5 5 5
Mixed water volume 40 °C l 10 10 10
Electrical data
Rated voltage V220 230 240 220 230 240 220 230 240
Rated output kW 0.9 1.0 1.1 1.8 2.0 2.2 1.8 2.0 2.2
Rated current A 4.1 4.3 4.5 8.3 8.7 9.1 8.3 8.7 9.1
Fuse/MCB rating A 10 10 10 10 10 10 10 10 10
Phases 1/N/PE 1/N/PE 1/N/PE
Frequency Hz 50/60 50/60 50/60
Application limits
Temperature setting range °C 35 - 85 35 - 85 35 - 85
Max. permissible pressure MPa 000
Max. flow rate l/min 555
Energy data
Standby power consumption over 24h at 38°C kWh 0.09 0.09 0.09
Standby energy consumption/24h at 65°C kWh 0.2 0.2 0.2
Energy efficiency category A A A
Versions
IP rating IP24 IP24 IP24
Type Open vented Open vented Open vented
Type of installation Undersink Undersink Undersink
Internal cylinder material PP PP PP
Thermal insulation material Polystyrene Polystyrene Polystyrene
Casing material PS PS PS
Colour white white white
Connections
Water connection G 3/8 G 3/8 G 3/8
Dimensions
Depth mm 230 230 230
Height mm 421 421 421
Width mm 263 263 263
Weights
Weight kg 3.0 3.0 3.0

22 | SNU 5 www.stiebel-eltron.com
GUARANTEE | ENVIRONMENT AND RECYCLING
Guarantee
The warranty conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products, it is increasingly the
case that warranties can only be issued by those subsidiaries.
Such warranties are only granted if the subsidiary has issued
its own terms of warranty. No other warranty will be granted.
We shall not provide any warranty for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.
GUARANTEE
ENVIRONMENT AND RECYCLING
INSTALLATION TEMPLATE (IN THE
MIDDLE OF THESE INSTRUCTIONS)

antitropf comfor t
85
°C
35
55
65
Eco
antitro pf comfor t
85
°C
35
55
65
Eco
79 mm
140 mm
407mm
263mm
407mm
263mm

antitropf comfor t
85
°C
35
55
65
Eco
antitro pf comfor t
85
°C
35
55
65
Eco
79 mm
140 mm
407mm
263mm
407mm
263mm
26�02�06�0011

Who gives the warranty
1. The warranty is given by Stiebel Eltron (Aust) Pty Ltd (A.B.N.
82 066 271 083) of 6 Prohasky Street, Port Melbourne, Victoria,
3207 (“we”, “us” or “our”).
The warranty
2. This warranty applies to Stiebel Eltron Water Heaters –
Models DHE 18 AU, DHE 27 AU, DEL 18 AU, DEL 27 AU, DHB-E
13 AU, DHB-E 13, DHB-E 18 AU, DHB-E 27 AU, HDBE 13 AU,
HDBE 18 AU, HDBE 27 AU, DHF 13 C AU, DHF 15 C AU, DHC
4, DHC 6, DHC 8, SN 5, SN 10, SNU 5 and SNU 10 (the “unit”)
manufactured after 1 May 2015.
3. Subject to the warranty exclusions we will repair or replace,
at our absolute discretion, a faulty component in your unit
free of charge if it fails to operate in accordance with its
specifications during the warranty period.
4. If we repair or replace a faulty component to your unit under
this warranty, the warranty period is not extended from the
time of the repair or replacement.
5. The warranty period commences on the date of completion
of the installation of the unit. Where the date of completion
of installation is not known, then the warranty period will
commence 2 months after the date of manufacture.
6. The warranty period for a unit used for domestic purposes is
shown in the table below. Domestic purposes means that the
unit is used in a domestic dwelling.
Component Warranty period
All components 5 years from the date of
completion of the installation
of the unit.
7. The warranty period for a unit used for commercial purposes
is shown in the table below. Commercial purposes means that
the unit is used for a non-domestic purpose and includes but
not limited to being used in a motel, hotel, mining camp or
nursing home.
Component Warranty period
All components 1 year from the date of
completion of the installation
of the unit.
Your entitlement to make a warranty claim
8. You are entitled to make a warranty claim if:
8.1. you own the unit or if you have the owner’s
consent to represent the owner of the unit;
8.2. you contact us within a reasonable time of
discovering the problem with the unit;
How you make a warranty claim
9. To make a warranty claim you must provide us with the
following information:
9.1. The model number of the unit;
9.2. A description of the problem with the unit;
9.3. The name, address and contact details (such as
phone number and e-mail address) of the owner;
9.4. The address where the unit is installed and the
location (e.g. in laundry);
9.5. The serial number of the unit;
9.6. The date of purchase of the unit and the name of
the seller of the unit;
9.7. The date of installation of the unit;
9.8. A copy of the certificate of compliance when the
unit was installed.
10. The contact details for you to make your warranty claim are:
Name: Stiebel Eltron (Aust) Pty Ltd
Address: 6 Prohasky Street, Port Melbourne,
Victoria, 3207
Telephone: [phone]
(8.00 am to 5.00 pm AEST Monday to Friday)
Contact person: Customer Service Representative
E-mail: [e-mail]
11. We will arrange a suitable time with you to inspect and test
the unit.
Warranty exclusions
12. We may reject your warranty claim if:
12.1. The unit was not installed by registered and
qualified tradespeople.
12.2. The unit was not installed and commissioned:
(a) in Australia;
(b) in accordance with the Operating and
Installation Guide; and
(c) in accordance with the relevant statutory
and local requirements of the State or
Territory in which the unit is installed.
12.3. The unit has not been operated or maintained in
accordance with the Operating and Installation Guide.
12.4. The unit does not bear its original Serial Number
or Rating Label.
12.5. The unit was damaged by any or any
combination of the following:
(a) normal fair wear and tear;
(b) connection to an incorrect water supply;
(c) connection to water from a bore, dam or
swimming pool;
(d) connection to an incorrect power supply;

(e) connection to faulty equipment, such as
damaged valves;
(f) foreign matter in the water supply, such
as sludge or sediment;
(g) corrosive elements in the water supply;
(h) accidental damage;
(i) act of God, including damage by flood,
storm, fire, lightning strike and the like;
(j) excessive water pressure, negative water
pressure (partial vacuum) or water pressure
pulsation.
12.6. The unit was damaged before it was installed
e.g. it was damaged in transit.
12.7. An unauthorised person has modified, serviced,
repaired or attempted to repair the unit without our
consent.
12.8. Non genuine parts other than those
manufactured or approved by us have been used on
the unit.
13. We may charge you:
13.1. for any additional transport costs if the unit is
installed more than 30 kilometres from our closest
authorised service technician.
13.2. for the extra time it takes our authorised service
technician to access the unit for inspection and
testing if it is not sited in accordance with the
Operating and Installation Guide and not readily
accessible for inspection.
13.3. for any extra costs of our authorised service
technician to make the unit safe for inspection.
14. You must ensure that access to the unit by our authorised
service technician is safe and free from obstruction.
15. Our authorised service technician may refuse to inspect and
test the unit until you provide safe and free access to it, at your
cost.
16. If we reject your warranty claim in accordance with clause
12, we may charge you for our authorised service technician’s
labour costs to inspect and test the unit.
17. In order to properly test the unit we may remove it to
another location for testing.
Australian Consumer Law
18. Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a
major failure.
19. The Stiebel Eltron warranty for the unit is in addition to
any rights and remedies you may have under the Australian
Consumer Law.



Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [email protected]
Kundendienst Tel. [phone] | Fax [phone] | [email protected]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [email protected]
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van vergissingen en technische wijzigingen! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmianytechniczne i
ewentualne błędy| Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések jogát
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Chyby a
technické zmeny sú vyhradené! Stand 8870
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6Prohasky Street | Port Melbourne VIC 3207
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Eferdinger Str. 73 | 4600 Wels
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Technology
Development Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[email protected]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.cz
Denmark
Pettinaroli A/S
Mandal Allé 21 | 5500 Middelfart
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.dk
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[email protected]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[email protected]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z o.o.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody, s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[email protected]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron-usa.com
A 275985-38253-8967
4<AMHCMN=hfjifb>