STIEBEL ELTRON SB 150 User manual

- 1 -
17 West Street
West Hatfield, MA 01088
Phone: [phone] * [phone]
Fax: [phone]
E-mail: [e-mail]
SB 150, SB 200
Glass Lined Indirectly Fired Water Heaters
With Single Heat Exchanger
INSTALLATION AND OPERATING INSTRUCTIONS
SB150 (40 gallon)
SB200 (50 gallon)

- 2 -
DANGER
•Water temperature over 125˚F can cause severe burns instantly or
death from scalds.
•Children, disabled and elderly are at highest risk of being scalded.
•Set the thermostat as low as practical. Settings the thermostat as
low as possible will reduce the risk of scalding and reduce energy
consumption.
•Feel water before showering or bathing.
•Special valves are available to provide anti-scald protection.
Consult a licensed plumber or the local pluming authority for more
information.
If the temperature and pressure relief valve on the SB tank opens
periodically, it may be due to thermal expansion in a closed water supply
system. Consult a licensed plumber, the local plumbing authority, or the
water supplier. Do not plug the Temperature and Pressure Relief Valve.
SB TANK PIPING WITH A “MIXING VALVE”
Usually, the maximum temperature of the outlet water will stay near
the setting of the thermostat. In some cases, however, hot water usage
patterns can cause the outlet water temperature to rise significantly
above the control settings.
The temperature of water going to the fixtures may be more
carefully controlled through the use of a mixing valve. This device blends
a controlled amount of cold water with the hot water from the tank to
provide a more constant temperature at the fixtures.

- 3 -
WARNING
There are no user serviceable parts on this product. Attempts to service
this product by someone other then a licensed plumber or heating
technician could void the warranty, cause property damage, personal
injury or loss of life.
A mixing valve does not eliminate the risk of scalding:
•Set the thermostat as low as practical.
•Feel water before bathing or showering.
•If anti-scald or anti-chill protection is required, use devices
specifically designed for such service. Install these devices in
accordance with their manufacturer’s instructions.
Install a new Temperature and Pressure Relief (“T & P”) Valve in the
tapping on the top of the tank marked “T&P VALVE”. Failure to do so
could result in property damage, personal injury or death.
•This Valve must comply with the Standard for Relief Valves and
Automatic Gas Shutoff devices for Hot Water Supply Systems (ANSI
Z21.22)
•No valve is to be placed between the T&P valve and the tank.
•Do not install valves, reducing couplings or other obstructions in the
relief valve discharge line.
•Do not install a T&P valve with a pressure settings in excess of 150 PSI
or a temperature setting in excess of 210˚F
•Pipe the discharge line to a location where hot water discharge will
not cause injury or damage.
•Do not run any portion of the discharge line through a location that
will be exposed to freezing temperatures.
•Pipe he discharge line to allow complete drainage of both the
discharge piping and the T&P valve.
Hydrogen gas can be produced in a hot water system that has not been
used for a long period of time (generally two weeks or more). Hydrogen
gas is extremely flammable. To prevent the possibility of injury under these
conditions, it is recommended that the hot water faucet be opened for
several minutes at the kitchen sink before you use any electrical
appliance, which is connected to the hot water system. If hydrogen is
present, there will probably be an unusual sound such as air escaping
through the pipe as hot water begins to flow. There should be no smoking
or open flame near the faucet at the time it is open.

- 4 -
I. Product description
The Stiebel Eltron SB series water heaters are indirectly fired designed to
generate hot water in conjunction with a solar collector system or a gas,
oil or pellet boiler using forced boiler water circulation. This indirect water
heater consists of an enameled steel tank in which a smooth coil is
located. A solar heated water/glycol mix or boiler water is pumped
through the heat exchanger coil and heats the water in the tank. The SB
series is not intended for use in heating any fluid other than water. It is also
not intended for use in gravity hot water heating systems.
II. Specifications
SB TANK
SB 150
SB 200
First hour rating (gal/hr)*
192
225
Boiler water output (btu / hr)
103, 149
116, 094
Boiler water flow (gal / min)
8.0
8.0
Coil head loss (ft w.c.)
2.6
2.6
Coil surface (sq. ft / m2)
12.1 / 1.12
14.3 / 1.32
Tank volume (gal / l)
39.0 / 147.63
52 / 196.84
Net weight (lbs / kg)
190 / 86.18
226 / 102.5
Filled weight (lbs / kg)
523 / 237.2
658 / 298.4
Connections (NPT)
Cool Drain
3/4 M
3/4 M
Boiler Supply
1 F
1 F
Boiler Return
1 F
1 F
Hot
3/4 M
3/4 M
Thermostat
3/4 F
3/4 F
Recirc
-
-
T&P Valve
3/4 F
3/4 F
Performance Specifications (I = B = R Certified Performance Ratings)
First Hour Rating (Gal/hr)
192.4
225.1
Cont. Draw Rating (Gal/hr)
158.0
178.2
Standby Heat Loss (F/hr)
1.9
1.3
Min Boiler Output (BTU/hr)
103, 149
116, 094
Boiler Water Flow (Gal/min)
8.0
8.0
•*First Hour Ratings are based on 58F˚ inlet water, 135F˚ hot water, and
180F˚ boiler supply water
•F = Female thread
•M = Male thread

- 5 -
Dimensions (in/cm)
Model
SB 150
SB 200
A
5 1/8 / 13.02
5 1/8 / 13.02
B
9 3/4 / 24.76
9 3/4 / 24.76
C
34 / 86.36
37 7/8 / 96.20
D
-
-
E
50 1/2 / 128.27
62 3/4 / 159.38
F
20 1/2
20 1/2