STIEBEL ELTRON SBB 300 PLUS Instruction Manual

BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
Solar-Warmwasserspeicher | DHW tank for solar systems
» SBB 300 plus
» SBB 400 plus
» SBB 600 plus

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 15
CONTENTS | SPECIAL INFORMATION
General information
OPERATION
1. General information ��������������������������������������� 15
1.1 Safety instructions���������������������������������������������� 15
1.2 Other symbols in this documentation ���������������������� 16
1.3 Units of measurement ����������������������������������������� 16
2. Safety�������������������������������������������������������� 16
2.1 Intended use����������������������������������������������������� 16
2.2 Safety instructions���������������������������������������������� 16
3. Appliance description ������������������������������������� 16
4. Cleaning, care and maintenance ������������������������� 17
4.1 Signal anode with consumption indicator ����������������� 17
4.2 Scaling ������������������������������������������������������������ 17
5. Troubleshooting �������������������������������������������� 17
INSTALLATION
6. Safety�������������������������������������������������������� 18
6.1 General safety instructions ����������������������������������� 18
6.2 Instructions, standards and regulations ������������������� 18
7. Appliance description ������������������������������������� 18
7.1 Standard delivery����������������������������������������������� 18
7.2 Accessories������������������������������������������������������� 18
8. Preparations ������������������������������������������������ 18
8.1 Installation site�������������������������������������������������� 18
8.2 Transport ��������������������������������������������������������� 19
9. Installation�������������������������������������������������� 19
9.1 Cylinder casing �������������������������������������������������� 19
9.2 Signal anode����������������������������������������������������� 19
9.3 Solar or heating installation���������������������������������� 19
9.4 Water connection and safety assembly �������������������� 20
9.5 Sensor DHW������������������������������������������������������ 20
9.6 Sensor solar cylinder ������������������������������������������ 20
9.7 Thermometer ���������������������������������������������������� 21
10. Commissioning ��������������������������������������������� 21
10.1 Initial start-up��������������������������������������������������� 21
10.2 Recommissioning����������������������������������������������� 21
11. Shutdown ��������������������������������������������������� 21
12. Maintenance ������������������������������������������������ 21
12.1 Draining the appliance ���������������������������������������� 21
12.2 Checking the safety valve ������������������������������������� 21
12.3 Replacing the signal anode����������������������������������� 21
12.4 Cleaning and descaling the appliance���������������������� 21
13. Specification ������������������������������������������������ 22
13.1 Dimensions and connections��������������������������������� 22
13.2 Details on energy consumption������������������������������ 26
13.3 Specification ����������������������������������������������������� 26
GUARANTEE
ENVIRONMENT AND RECYCLING
OPERATION
1. General information
The chapter "Operation" is intended for appliance users and qual-
ified contractors.
The chapter "Installation" is intended for qualified contractors.
Note
Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
!
KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol Type of risk
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-seri-
ous or minor injury.
!

OPERATION
Safety
16 | SBB 300-600 plus www.stiebel-eltron.com
1.2 Other symbols in this documentation
Note
General information is identified by the adjacent symbol.
 Read these texts carefully.
Symbol Meaning
Material losses
(appliance damage, consequential losses and environmen-
tal pollution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Units of measurement
Note
All measurements are given in mm unless stated oth-
erwise.
2. Safety
2.1 Intended use
The appliance is intended for heating domestic hot water in con-
junction with solar collectors and optionally with further heat
sources for reheating the upper half of the cylinder.
This appliance is intended for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-do-
mestic environment, e.g. in a small business, as long as it is used
in the same way.
Any other use beyond that described shall be deemed inappropri-
ate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
2.2 Safety instructions
WARNING Burns
There is a risk of scalding at outlet temperatures in ex-
cess of 43°C.
!
WARNING Injury
The appliance may be used by children aged 8 and older
and persons with reduced physical, sensory or mental
capabilities or a lack of experience and know-how, pro-
vided that they are supervised or they have been in-
structed on how to use the appliance safely and have
understood the resulting risks. Children must never play
with the appliance. Children must never clean the ap-
pliance or perform user maintenance unless they are
supervised.
Note
The appliance is pressurised.
During the heat-up process, expansion water will drip
from the safety valve. If water continues to drip when
heating is completed, please inform your qualified con-
tractor.
3. Appliance description
The DHW is heated via two smooth tube internal indirect coils. In
addition, a threaded immersion heater and/or flanged immersion
heater or heat exchanger can be connected. You can use the ap-
pliance to supply one or several draw-off points.
The appliance is equipped with an inspection flange and ther-
mometer.
The steel cylinder is coated on the inside with special directly
applied enamel and is equipped with a signal anode. The anode
with consumption indicator protects the cylinder interior from
corrosion. The cylinder is surrounded by foam insulation and a
cylinder jacket.
!

OPERATION
Cleaning, care and maintenance
ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 17
4. Cleaning, care and maintenance
 Have the function of the safety assembly and electrical safe-
ty of the fitted accessories regularly checked by a qualified
contractor.
 Have the protective anode checked by a qualified contractor
after the first two years of use. The qualified contractor will
then determine the intervals at which repeat checks should
be performed.
 Never use abrasive or corrosive cleaning agents. A damp
cloth is sufficient for cleaning the appliance.
4.1 Signal anode with consumption indicator
!
Material losses
If the consumption indicator changes colour from white
to red, have the signal anode checked by a qualified con-
tractor and if necessary replaced.
26�03�20�0001
23
1
1 Signal anode with consumption indicator
2 White = Anode OK
3 Red = Requires checking by heating contractor
4.2 Scaling
Almost every type of water will deposit limescale at high tem-
peratures. This settles inside the appliance and affects both the
performance and service life. If a threaded immersion heater or
flanged immersion heater is fitted, the heating elements must
be descaled from time to time. A qualified contractor who knows
the local water quality will tell you when the next service is due.
 Check the taps regularly. Limescale deposits at the tap out-
lets can be removed using commercially available descaling
agents.
5. Troubleshooting
Call your qualified contractor.
To facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000):
Nr. 000000-0000-000000
D0000063493

18 | SBB 300-600 plus www.stiebel-eltron.com
INSTALLATION
Safety
INSTALLATION
6. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
6.1 General safety instructions
We can only guarantee trouble-free function and operational reli-
ability if original spare parts intended for the appliance are used.
6.2 Instructions, standards and regulations
Note
Observe all applicable national and regional regulations
and instructions.
7. Appliance description
7.1 Standard delivery
The following are delivered with the appliance:
- Sensor DHW
- Fixing straps with closure elements
- Thermometer (located in the DHW outlet on delivery)
- Label "Signal anode information"
- Adaptor with flat gasket for connecting a DHW circulation line
SBB 300-400 plus
- Cold water inlet pipe with flat gasket
- Adjustable feet
7.2 Accessories
Required accessories
Safety assemblies and pressure reducing valves are available
to suit the prevailing supply pressure. These type-tested safety
assemblies protect the appliance against impermissible excess
pressure.
Further accessories
Threaded immersion heaters, flanged immersion heaters and in-
ternal indirect coils are available as accessories.
8. Preparations
8.1 Installation site
 Always install the appliance in a room free from the risk of
frost and near the draw-off point.
 Ensure the floor has sufficient load bearing capacity and
evenness (see chapter “Specification / Data table”).
 Observe the room height and height when tilted (see chapter
"Specification/ Data table").
SBB 300-400 plus
26�03�20�0008
 Use the adjustable feet to compensate for any unevenness in
the floor.
Minimum clearances
The minimum side clearances can be swapped to left or right.
≥500 ≥300
≥300≥800
≥100
D0000060125
 Maintain the minimum clearances.

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 19
INSTALLATION
Installation
8.2 Transport
!
Material losses
We recommend removing the cylinder casing for trans-
portation to the installation location to prevent it from
becoming dirty or damaged.
SBB 600 plus
 Both side insulation sections can be removed for transporta-
tion in tight spaces. To do this, remove the cylinder casing.
26�03�20�0003
 Use the fixing straps to refit the thermal insulation sections
following transport.
11
D0000047882
1 Side insulation segment
 Ensure that the closures are positioned in the joint between
a side insulation segment and the thermal insulation of the
cylinder.
9. Installation
9.1 Cylinder casing
Note
Open or remove the cylinder casing before fitting the DHW
circulation and indirect coil lines.
Fit the cylinder casing before installing a threaded im-
mersion heater.
The plinth trim should be fitted after the tightness check.
9.2 Signal anode
!
Material losses
The appliance must not be operated without a consump-
tion indicator or with a damaged one, as water will leak
out once the anode is depleted.
 Affix the label "Signal anode information" in a clearly visible
position on the thermal insulation.
9.3 Solar or heating installation
 Before connection, flush the indirect coil with water.
 Route the connecting lead to the solar or heating circuit con-
trol unit.
9.3.1 Water quality, solar circuit
A glycol/water mixture of up to 60% is permitted for the indirect
coil in the solar circuit if only dezincification-resistant metals,
glycol-resistant gaskets and diaphragm expansion vessels suitable
for glycol are used throughout the installation.
9.3.2 Oxygen diffusion
!
Material losses
Avoid open vented solar thermal systems and plastic
pipes which are permeable to oxygen.
With plastic pipes that are permeable to oxygen, oxygen diffusion
may lead to corrosion on the steel components of the solar thermal
system (e.g. on the indirect coil of the DHW cylinder).
!
Material losses
Avoid open heating systems and plastic pipes in under-
floor heating systems which are permeable to oxygen.
In underfloor heating systems with plastic pipes that are per-
meable to oxygen and in open vented heating systems, oxygen
diffusion may lead to corrosion on the steel components of the
heating system (e.g. on the indirect coil of the DHW cylinder, on
buffer cylinders, steel heating elements or steel pipes).
!
Material losses
The products of corrosion (e.g. rusty sludge) can settle in
the heating system components and can result in a lower
output or fault shutdowns due to reduced cross-sections.

20 | SBB 300-600 plus www.stiebel-eltron.com
INSTALLATION
Installation
9.4 Water connection and safety assembly
9.4.1 Safety instructions
Note
Carry out all water connection and installation work in
accordance with regulations.
!
Material losses
For the combined use of a threaded immersion heater
and plastic pipework systems, observe the maximum
permissible temperature and the maximum permissible
pressure specified in chapter "Specification/ Data table".
!
Material losses
Operate the appliance only with pressure-tested taps.
Cold water line
Galvanised steel, stainless steel, copper and plastic are approved
materials.
A safety valve is required.
DHW line
Stainless steel, copper and plastic pipework are approved ma-
terials.
9.4.2 Connection
 Flush the pipes thoroughly.
The maximum permissible pressure must not be exceeded (see
chapter "Specification/ Data table").
 Install a type-tested safety valve in the cold water supply
line. Please note that, depending on the supply pressure, you
may also need a pressure reducing valve.
 A DHW circulation line can be fitted to the "DHW circulation"
connection (see chapter "Specification/ Dimensions and con-
nections"). Insert the adaptor supplied with flat gasket and
an extension.
 Connect the DHW outlet line and the cold water inlet line.
SBB 300-400 plus
26�02�09�0035
1 2
1 Cold water connection
2 Cold water inlet pipe
 Connect the cold water supply directly to the cylinder or fit
the connection pipe between the cylinder feet.
 When making the connection, counter-hold the fitting with a
spanner (size 36).
 Check the stability of the connecting pipe and secure it fur-
ther if required.
All appliance models
 Size the drain pipe so that water can drain off unimpeded
when the safety valve is fully opened.
 Fit the discharge pipe of the safety valve with a constant
downward slope and in a room free from the risk of frost.
 The safety valve discharge aperture must remain open to
atmosphere.
9.5 Sensor DHW
D0000046061
 Bend the contact spring of the DHW sensor (see diagram).
This prevents the sensor sliding out of the sensor well and
optimises the heat conducting contact with the well.
 Insert the DHW sensor as far as it will go into the sensor well
(see chapter "Specification / Dimensions and connections").
 Route the connection lead to the heating control unit.
9.6 Sensor solar cylinder
 Fit the sensors for the solar control units used according to
the relevant installation instructions (for sensor wells, see
chapter "Specification / Dimensions and connections").
 Route the connection lead to the solar control unit.

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 21
INSTALLATION
Commissioning
9.7 Thermometer
26�03�20�0005
1
1 Thermometer
 Insert the thermometer as far as it will go and align it.
10. Commissioning
10.1 Initial start-up
 Open a draw-off point until the appliance has filled up and
the pipework is free of air.
 Vent the internal indirect coil.
 Carry out a tightness check.
 Check the solar thermal system for correct function.
 Fit and check accessories as required.
 Check the safety valve for correct function.
 Check that the DHW temperature displayed on the solar con-
trol unit is correct.
10.1.1 Appliance handover
 Explain the appliance function to users and familiarise them
with its operation.
 Make the user aware of potential dangers, especially the risk
of scalding.
 Hand over these instructions.
10.2 Recommissioning
See chapter "Commissioning/ Initial start-up".
11. Shutdown
 Disconnect any accessories installed from the mains at the
MCB/fuse in the fuse box.
 Drain the appliance. See chapter "Maintenance/ Draining the
appliance".
12. Maintenance
WARNING Electrocution
Carry out all electrical connection and installation work
in accordance with relevant regulations.
If you need to drain the appliance, observe chapter "Draining the
appliance".
12.1 Draining the appliance
WARNING Burns
Hot water may escape during the draining process.
If the appliance needs to be drained for maintenance or to protect
the whole installation when there is a risk of frost, proceed as
follows:
 Close the shut-off valve in the cold water inlet line.
 Open the hot water taps on all draw-off points.
 Drain the appliance via the drain valve of the safety
assembly.
12.2 Checking the safety valve
 Regularly vent the safety valve on the safety assembly until a
full water jet is discharged.
12.3 Replacing the signal anode
A segmented signal anode is available as a spare part.
 Replace the signal anode if it becomes depleted. For this, en-
sure there is a good connection between the anode and the
cylinder (maximum permissible transition resistance 0.3Ω).
12.4 Cleaning and descaling the appliance
26�03�01�0847
1
1
1 Threaded holes for forcing screws
 To separate the flange plate from the flanged connector, use
the threaded holes and forcing screws.
For the torque of the flange screws, see chapter "Specification/
Dimensions and connections".
 Never use descaling pumps.
 Never treat the cylinder surface or the signal anode with des-
caling agents.

22 | SBB 300-600 plus www.stiebel-eltron.com
INSTALLATION
Specication
13. Specification
13.1 Dimensions and connections
Appliance sectional view
i01
h28
i07
h16
h43 c10
e01
d25
c03
c06
e02
d26
c01
D0000048208

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 23
INSTALLATION
Specication
SBB 300 plus
43
73
700
550
1679
1239
1179
1025
557
365
1704
1339
1239
975
865
280
i01
h28
i07
h16
h43 c10
e01
d25
c03
c06
e02
d26
c01
620
i18
D0000017546
SBB 300 plus
c01 Cold water inlet Male thread G 1 A
c03 Cold water inlet pipe Male thread G 1 A
c06 DHW outlet Male thread G 1 A
c10 DHW circulation Male thread G 1/2 A
d25 Solar flow Female thread G 1
d26 Solar return Female thread G 1
e01 Heating flow Female thread G 1
e02 Heating return Female thread G 1
h16 Sensor DHW Diameter mm 9.5
h28 Sensor solar cylinder Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i01 Flange Diameter mm 210
Pitch circle diameter mm 245
Screws M 12
Torque Nm 70
i07 Electric emergency/booster heater Female thread G 1 1/2
i18 Protective anode Female thread G 1 1/4

24 | SBB 300-600 plus www.stiebel-eltron.com
INSTALLATION
Specication
SBB 400 plus
43
65
750
600
1848
1298
1238
1078
560
367
1873
1600
1298
1130
867
282
i01
h28
i07
h16
h43 c10
e01
d25
c03
c06
e02
d26
c01
620
i18
D0000017548
SBB 400 plus
c01 Cold water inlet Male thread G 1 A
c03 Cold water inlet pipe Male thread G 1 A
c06 DHW outlet Male thread G 1 A
c10 DHW circulation Male thread G 1/2 A
d25 Solar flow Female thread G 1
d26 Solar return Female thread G 1
e01 Heating flow Female thread G 1
e02 Heating return Female thread G 1
h16 Sensor DHW Diameter mm 9.5
h28 Sensor solar cylinder Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i01 Flange Diameter mm 210
Pitch circle diameter mm 245
Screws M 12
Torque Nm 70
i07 Electric emergency/booster heater Female thread G 1 1/2
i18 Protective anode Female thread G 1 1/4

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 25
INSTALLATION
Specication
SBB 600 plus
1735
1252
1192
1040
595
405
50
1760
1453
1252
1089
862
277
750
920
i01
h28
i07
h16
h43 c10
e01
d25
c01
c06
e02
d26
770 620
i18
D0000017550
SBB 600 plus
a23 Appliance Width excl. side insulation sections mm 770
c01 Cold water inlet Male thread G 1 A
c06 DHW outlet Male thread G 1 A
c10 DHW circulation Male thread G 1/2 A
d25 Solar flow Female thread G 1
d26 Solar return Female thread G 1
e01 Heating flow Female thread G 1
e02 Heating return Female thread G 1
h16 Sensor DHW Diameter mm 9.5
h28 Sensor solar cylinder Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i01 Flange Diameter mm 210
Pitch circle diameter mm 245
Screws M 12
Torque Nm 70
i07 Electric emergency/booster heater Female thread G 1 1/2
i18 Protective anode Female thread G 1 1/4

26 | SBB 300-600 plus www.stiebel-eltron.com
INSTALLATION
Specication
13.2 Details on energy consumption
The product data complies with EU regulations relating to the
Directive on the ecological design of energy related products (ErP).
SBB 300 plus SBB 400 plus SBB 600 plus
187873 187874 187875
Manufacturer STIEBEL ELTRON STIEBEL ELTRON STIEBEL ELTRON
Energy efficiency class C C
Standby losses W79 92 121
Cylinder capacity l322 434 639
13.3 Specification
SBB 300 plus SBB 400 plus SBB 600 plus
187873 187874 187875
Hydraulic data
Nominal capacity l305 416 611
Capacity, upper indirect coil l6.8 7.5 11.3
Capacity, lower indirect coil l 10.5 10.7 16.7
Surface area, upper indirect coil m² 1.1 1.3 1.8
Surface area, lower indirect coil m² 1.5 1.7 2.6
Pressure drop at 1.0 m³/h, upper indirect coil hPa 16 19 5
Pressure drop at 1.0 m³/h, lower indirect coil hPa 22 24 6
Mixed water volume 40°C (15°C/60 °C) l 504 677 964
Application limits
Max. permissible pressure MPa 1 1 1
Test pressure MPa 1.5 1.5 1.5
Max. permissible temperature °C 95 95 95
Max. flow rate l/min 38 45 50
Max. recommended collector aperture area m² 6 8 12
Energy data
Standby energy consumption/24 h at 65 °C kWh 1.9 2.2 2.9
Dimensions
Height mm 1679 1848 1735
Diameter mm 700 750 920
Height when tilted mm 1820 1995 1965
Weights
Weight, dry kg 154 187 260
Weight, full kg 442 578 824

ENGLISH
www.stiebel-eltron.com SBB 300-600 plus | 27
GUARANTEE | ENVIRONMENT AND RECYCLING
GUARANTEE
ENVIRONMENT AND RECYCLING
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.
GUARANTEE
ENVIRONMENT AND RECYCLING



Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [email protected]
Kundendienst Tel. [phone] | Fax [phone] | [email protected]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [email protected]
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van ver
g
issin
g
en en technische wi
j
zi
g
in
g
en! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian
y
techniczne i
ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések
j
o
g
át
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Ch
y
b
y
a
technické zmeny sú vyhradené! Stand 9147
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne VIC 3207
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Gewerbegebiet Neubau-Nord
Margaritenstraße 4 A | 4063 Hörsching
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[email protected]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[email protected]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron-usa.com
A 255305-39497-9153
4<AMHCMN=ffdafd>