Still CX-T User manual

Original instructions
CX-T Liftrunner
CX-40
1050
51048070301 EN - 10.2010

1Use
Operation
Operation
CAUTION
Strictly follow the instructions given by the trailer
manufacturer.
Controls
• Trailer lift/lower control as standard using a
switch and foot switch
• As an option: automatic lifting or lowering
by simply pressing the foot switch
– Once the trailers have been attached and
connected hydraulically, step on the truck
platform and press the "lift" button to put the
trailers in the raised position.
– To put the trailers in the lowered position,
press the "lower" button.
25
1048070301 [EN]

Use 1
Operation
– The position of the trailers (raised or low-
ered) can be locked using the switch lo-
cated near to the operator’s backrest. The
operator can then step on and off the truck
without affecting the position of the trailers.
– To unlock the position of the trailers, turn
the button to the required position.
CAUTION
Risk of damaging the containers and/or their
wheels.
Check that all the trailers are raised, especially the
trailer at the end of the train.
CAUTION
Risk of shearing hydraulic hoses, damaging equip-
ment and losing control of the trailer train.
Conduct a visual check to make sure all connecti-
ons have been made (tiller lock and hose connec-
tion).
CAUTION
Equipment damage.
Never drive on a ramp.
DANGER
Risk of crushing.
Never walk between two trailers.
DANGER
Risk of injury.
Never climb on the tillers or trailers.
51048070301 [EN] 3

1Use
DANGER
Risk of injury to the operator or others, and risk
of damaging equipment due to poor visibility in
reverse gear unladen.
The operator must be trained to drive the truck.
DANGER
Risk of crushing feet of others due to automatic
lowering of trailers when operator leaves platform.
Before stopping and leaving the platform, the
operator must ensure that nobody is in the danger
area.
45
1048070301 [EN]

2Electrical system
Electric Circuit Diagram
Electric Circuit Diagram
5 51048070301 [EN]

Electrical system 2
Electric Circuit Diagram
51048070301[EN] 6

2Electrical system
Description of components
Description of components
Description of components
Component Initials
A1 Controller
A11 Battery charger
A111 Diode card
A112 Charger voltage socket support
A2 Tiller unit
F1 Power fuse
F3 Control fuse
G1 Battery
H1 Warning horn;
K1 Line switch
M1 Traction motor
M2 Pump motor
P1 Forward/reverse travel
P3 Tilt potentiometer
6P20 Multifunction indicator
S1 Ignition key
2S1 Lowering push button
4S1 Horn push button
S2 Emergency stop
2S2 Lift push button
S4 Tiller foot pull switch
S5 High base lift
S6 Low base lift
S7 Loading frame sensor
S9 Height restriction sensor unlocking pushbutton
S10 Height restriction sensor or speed reduction
1S30 Anti-crush switch
Y1 Lowering solenoid valve
Y2 Electromagnetic brake
7 51048070301 [EN]

Electrical system 2
Description of components
Y3 Base lift solenoid valve
Y5 Base lift solenoid valve
Y6 Solenoid valve only present on EXV12: used to stop forks instantaneously when being raised
Option On-board charger (A11 + A111 + A112)
51048070301[EN] 8

3Hydraulic system
Hydraulic diagram
Hydraulic diagram
9 51048070301 [EN]

Hydraulic system 3
Hydraulic diagram
1 Pump motor
2 Hydraulic pump
3 Hydraulic oil filters
4 Y6 on/off solenoid valve
5 Pressure limiter
6 Pressure port
7 Tank
8 Non-return valve
9 Flow limiter
10 Y1 proportional solenoid valve
11 Cylinder
51048070301[EN] 10