Style selections LT2026WWMV User manual

UTILITY SINK AND CABINET
ITEM #0185379
MODEL #LT2026WWMV
Français p. 12
Español p. 23
1IS2626
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
EB1278

2IS2626
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
ASink Basin 1
B Strainer Kit 1
C Trim Piece 1
DHose Guard with Soap Dish 1
ECabinet Body 1
FDoor 2
C
E
B
A
F
D

3IS2626
PART DESCRIPTION QUANTITY
GPull-out Sprayer 1
HFaucet 1
ILocknut 2
JHose 1
K Wing Nut 1
LZinc Weight 1
O
N
P
Q
R
GH
I
J
K
L
PART DESCRIPTION QUANTITY
M Water Supply Line 2
N Tailpiece 1
ONut 2
P Washer 1
QP-Trap 1
R Wall Tube 1
M
O

4IS2626
HARDWARE CONTENTS (Shown actual size)
BB
AA
Mounting Plate
Qty. 4
Mounting Plate Screw
Qty. 8
DD
Hinge
Qty. 4
Hinge Screw
Qty. 8
FF
EE
Knob
Qty. 2
Knob Screw
Qty. 2
GG
Screw Cap
Qty. 24
HH
Rubber Bumper
Qty. 4
II
Large Screw
Qty. 2
CC

5IS2626
PREPARATION
Before cutting, drilling or hammering into any wall surface, verify the location of electrical, plumbing
and gas lines. Cutting any of these may cause serious injury. If needed, contact your electrician,
plumber or service person.
WARNING
Before beginning assembly of the product, make sure all parts are present. Compare parts with
package
contents list. If any part is missing or damaged, do not attempt to assemble the product.
Plumbing should be done by a qualified plumber and in accordance with national and local plumbing
codes. For shipping purposes, corner protectors are attached to the cabinet body and need to be
removed. If necessary, use small pliers to remove staples.
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
SAFETY INFORMATION
Estimated Assembly Time: 40 minutes
Tools Required for Assembly (not included): Drill, Hacksaw, Pipe Wrench, Pencil, Silicone
Caulk/Sealant, Plumbers Putty, and Wood Shims
Disassemble strainer kit (B), by unscrewing locknut
and removing
rubber washer. Unscrew nut and remove
tailpiece washer from strainer kit (B).
NOTE: Tailpiece washer will be used in step 9.
Apply a sufficient amount of plumbers putty between
the strainer and sink basin (A). Insert strainer body
through the drain hole in the sink basin (A).
Hold strainer body firmly in place, position rubber washer
on strainer body under the sink basin (A).
Screw lock nut onto the threaded shank of the strainer
body and tighten with a pipe wrench.
NOTE: DO NOT OVERTIGHTEN and remove any
excess plumbers putty from strainer body and sink
basin (A).
1. 1
A
B
B
ASSEMBLY INSTRUCTIONS

6IS2626
Using faucet kit, position faucet (H) on sink basin (A)
and hand tighten locknuts (I).
Attach hose (J) to pull-out sprayer (G) and tighten
securely.
Pass hose (J) through faucet and adjust the position of
the faucet (H) so that hose (I) does not rub against the
edge of the sink (A).
Unscrew wing nut (K) from zinc weight (L). Slide hose (J)
through wing nut (K) and zinc weight (L) then tighten in
its final position.
Attach hose (J) onto the center check valve on the
faucet (H) by turning nut counterclockwise and tighten
securely.
2. 2H
I
G
J
K
L
Connect the water supply line (M) by threading the
large connector nut onto faucet (H) and tighten securely.
Repeat for the second supply line (M).
NOTE: DO NOT OVERTIGHTEN.
3. 3H
M
M

7IS2626
Insert screw caps (GG) into each exposed screw head.
NOTE: Wall mounting is recommended. Hold the cabinet
body (E) in the desired position. Using the pre-drilled
holes in hanging rail, insert wood shims (not included)
between wall and cabinet body (E) until snug.
Place sink basin (A) into cabinet body (E) and check
for proper clearance. With sink basin (A) removed,
attach cabinet body (E) to wall using appropriate
mounting hardware (not included).
6. 6
E
Hardware Used
x 24
Screw Cap
GG
GG
GG
Fasten mounting plates (AA) to cabinet body (E) using
mounting plate screws (BB) with the long side of mounting
plates (AA) pointing to the front of the cabinet body (E).
NOTE: Do not overtighten mounting plate screws (BB).
5.
Hardware Used
x 4
Mounting Plate
AA
x 8
Mounting Plate Screw
BB
5
BB
AA
Attach trim piece (C) to cabinet body (E) with large
screws (II).
NOTE: Finished edges of cabinet body (E) face away
from wall.
4. 4
E
Hardware Used
x 2
Large Screw
II
C

8IS2626
Slip nut (O) onto wall tube (R).
Position two nuts (O) and one washer (P) onto
tailpiece (N).
Slip tailpiece (N) into p-trap (Q). Slip washer (P) down
tailpiece (N) and fasten using nut (O).
Insert wall tube (R) into p-trap (Q) and hand tighten
all nuts (O).
Holding plumbing assembly in the desired position,
measure wall tube (R) and tailpiece (N), to required
length. Remove wall tube (R) and tailpiece (N) and cut
with a hacksaw.
NOTE: Cut untapered end of tailpiece (N) and
wall tube (R). Be sure to remove burrs with a file or
sandpaper.
8. 8
Place a bead of silicone caulk/sealant around the top
edge of the cabinet body (E). Carefully set sink basin (A)
into cabinet body (E).
Place a bead of silicone caulk/sealant (not included)
on the backside of the backsplash on sink basin (A).
Place hose guard with soap dish (D) into either side of
the sink basin (A).
NOTE: Hose guard with soap dish (D) is shown on the
left side of sink basin (A) and can be used to secure the
discharge hose from washing machine.
7. 7
A
E
D
R
Q
N
O
P
O

9IS2626
Fasten hinges (CC) to doors (F) with hinge screws (DD).
NOTE: Do not overtighten hinge screws (DD).
11.
Hardware Used
x 4
Hinge
CC
x 8
Hinge Screw
DD
F
DD
CC
Connect the water supply line (M) by threading the
small metal connector nut onto the water supply
valve outlet and tighten securely.
Repeat for the second supply line (M).
NOTE: Check for leaks. If a leak appears, loosen
nuts completely and check washer alignment. If a
leak persists, carefully tighten nuts with a wrench.
NOTE: DO NOT OVERTIGHTEN.
10. 10
M
11
Loosely connect wall tube (R) and tailpiece (N) to
p-trap (Q).
Insert wall tube (R) into waste drain and tighten
using existing hardware.
Using tailpiece washer from strainer kit (B), place it
on top of tailpiece (N). Fasten tailpiece (N) to strainer
kit (B) using nut (O).
NOTE: DO NOT OVERTIGHTEN.
9. 9
R
Q
A
NO
P
B

10 IS2626
13
EE
F
FF
F asten knobs (EE) to doors (F) using knob screws (FF).
13.
Hardware Used
x 2
Knob
EE
x 2
Knob Screw
FF
F asten hinges (CC) to mounting plates (AA).
Place bumpers (HH) on doors (F) where they come in
contact with the cabinet body (E).
NOTE: If hinges (CC) need adjusting, follow the hinge
adjustment instructions in TROUBLESHOOTING.
12. 12
CC
Hardware Used
x 4
Rubber Bumper
HH
AA
Cleaning with a dry cloth may be sufficient, but for other stains or marks wipe gently with a damp
cloth. DO NOT use strong detergents or abrasive cleaners; they may damage the surface of
this
product.
CARE AND MAINTENANCE