STYLECRAFT GN2539 User manual

Oct 8, 2015 ○
E
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Unpack all parts from carton to ensure there are no missing or damaged parts.
If any parts are missing or damaged, do not attempt to assemble or use the product.
Please contact customer service for replacement.
CARTON CONTENTS
Part #
Description
Quantity
Diagram
Part #
Description
Quantity
Diagram
A
T-Bar
1pc
G
Top Bar
1pc
B
Blade
1pc
H
Two-Prong
Stake
1pc
C
Blade
1pc
I
Stake Bar
1pc
D
Nut
2pcs
J
“L” wrench
1pc
E
Washer
2pcs
K
Locking
Screw
1pc
F
Cap Nut
2pcs
L
Wrench
1pc
ITM. / ART. 463766
Model #: GN2539Large Wind Catcher
For assistance with assembly or installation, parts and customer service, call toll free:
1-855-766-1880 (US, CA / English and Spanish only) Monday - Friday
8:00 am - 5:00 pm (Central Time) or email [email protected]

Oct 8, 2015 ○
E
ASSEMBLY INSTRUCTIONS
Caution: Using the wrench (F) to tighten parts may cause damage to painted surfaces. If possible, protect
parts before wrench tightening.
1. Connect the T-Bar (A) with one of the two Blades (B or C) by inserting one of the threaded ends of the T-bar through the
middle hole of the Blade. (Step 1) Be sure blade is facing the correct direction. Note label on outer side of blade.
2. Fasten the Blade to the T-Bar by applying one Nut (D), Washer (E) and Cap Nut (F). Hand-tighten Nut and Cap Nut, then
tighten with Wrench (L). Repeat for other blade. (Step 2)The two blades should face opposite directions.
3. Thread the Stake Bar (I) through the ring on the Two-Prong Stake (H). Align the stake on the Stake Bar with the notch on
the ring, creating a four-prong stake. (Step 3)
4. Connect the Top Bar (G) with the assembled Stake Bar created in Step 3. Use the Locking Screw (K) to fasten the
connection. Use the “L” Wrench (J) to tighten the connection. (Step 4)
5. Connect the Bar Assembly in Step 4 with the Blade Assembly in Step 2 by inserting the top of the Top Bar (G) into the end
of the T-Bar (A). (Step 5)
6. Set up your wind catcher in your garden by pushing the assembled unit into the ground.
Step&1&
1
Step&2&
Step&3&
Step&5&

Oct 8, 2015 ○
E
TROUBLE SHOOTING
1. If the blade does not spin, make sure the two blades are assembled
correctly. The front side of the blades (where the ball bearing is visible)
should face outside. The backside of blades (where the ball bearing is
covered) should face inside. The two blades should face opposite
directions.
2. If one blade is spinning while the other one is not, or if one blade is spinning faster than the other, pay attention to below:
A. Rotate the T-Bar so that the two blades are facing the direction of the wind, or
B. Wait until the wind is stronger. Wind speed and/or direction change may cause one blade to spin faster than the other.
3. The two Blades (B & C) are designed to spin in opposite directions. If wind speed or direction change, they may spin in the
same direction. Wait until the wind is at a steady speed to experience proper spinning.
WARNINGS & CAUTIONS
1. This item is not a toy. DO NOT ALLOW CHILDREN TO CLIMB ON, HANG FROM, OR PLAY WITH THIS ITEM.
2. When the blades are spinning at a high speed, DO NOT TRY TO TOUCH BLADES AS IT MAY CAUSE INJURY.
3. Remove the T-Bar and Blade Assembly when the wind speed reaches 50 MPH or greater.
CARE & MAINTENANCE
To clean, use a soft cloth or sponge. To avoid damaging the finish, DO NOT USE ABRASIVE CLEANERS OR STEEL WOOL.
Made In China