sugar-valley Vistapool User manual

VISTAPOOL CONTROL SYSTEM
INSTALLATION GUIDE 2016
Our modules allow connection remote control of all our
devices via the Internet.
The client monitors, controls and adjusts all components
and parameters of the pool from anywhere in the world.
Professional pool maintenance controls all of them remotely.
The pool automatically generates statistics about the history
of its parameters.
The WIFI Module must be within the
scope of coverage of the wireless
network that will be connected.
WIRELESS NETWORK
COVERAGE
WIFI NETWORK REQUIREMENTS AND RECOMMENDATIONS
DHCP AUTOMATIC IP ASSIGNMENT
The DSL router has to be configured to enable this service for new connections. The WIFI module uses this protocol to automatically obtain an IP address from the router. If you have experienced problems with your WIFI Module
configuration and the box does not automatically connect to the router, check if DHCP is enabled. To do so, enter the router web address with a web browser (it is usually 192.168.1.1 or 192.168.0.1) and gain access to the control
panel by setting the user and password required by the router. Enter the DHCP option and enable it. Finally save and apply the configuration change to let the router work with the new configuration.
WIFI ENCRYPTION
Swimming pool water filtering is a very delicate operation, and its control must have a certain degree of protection against unwanted access and even malicious intrusions. Therefore it is strongly recommended to use a strong
encryption protocol when installing a swimming pool connection using the WIFI network. Several tests and documents have shown that WEP encryption have some security flaws and therefore should be replace it with WPA
encryption protocol. Nevertheless, many homes and companies still uses WEP encryption. If you have WEP as encryption protocol, change it by connecting to the router control panel, as explained in the previous section. Then enter
“Wireless settings” and change the WEP encryption to WPA. You can always use the same password as in the WEP encryption. Always remember to erase and create again your wireless network connection on your PC.
2 WIFI MODULE CONFIGURATION
2.5
2.6
2.3 2.4
2.7 2.9 2.102.8
12:30 25º
man
off
man
off
CoverPol 1
LOW
00 gr/h
%
hydrolysis / electrolysis
Pr onPol 1
Pol 2
250mA
pH 7.5 OFF
AL37.0
7.2
Rx
mV
700 OFF
AL3FL1
700
Cl
ppm
1.00 FL2
FL1
1.00
Cu/Ag ionization
measures
1 2 3 4
TANK
2.22.1
Ared (12V)
green (COM-B)
black (GND)
yellow (COM-A)
•Turn off the device by pressing the ON/OFF
switch and disconnect it from the plug.
•Take off the connectors lid using a screwdriver.
•Plug the WIFI Module into the corresponding
connector (WIFI) of the electronic circuit, with
the red wire positioned at the top.
•If the WiFi Module is properly connected, one
of the green LEDs will blink and the other will
remain on.
Once the WIFI module is connected, restart your unit. In the System Settings menu will appear the Network option.
pantalla 2.4 WIFI: Select WIFI to scan the available networks accessible to the module. The search will be done automatically.
pantalla 2.5 Select the desired network accessible to the WIFI module.
pantalla 2.6 Enter the password in the pop-up keyboard. Scroll up and down with the up/down keys and left to right with the
plus/minus keys. To select a letter press the OK.
pantalla 2.7 Configuration: For a more detailed configuration enter this menu or contact your installer.
pantalla 2.9 Status: Check the status of your connection.
pantalla 2.10 Test connection: Check that your connection has been successfully established..
INTRODUCTION
1

3VISTAPOOL CONFIGURATION
12:30 25º
man
off
man
off
CoverPol 1
LOW
00 gr/h
%
hydrolysis / electrolysis
Pr onPol 1
Pol 2
250mA
pH 7.5 OFF
AL37.0
7.2
Rx
mV
700 OFF
AL3FL1
700
Cl
ppm
1.00 FL2
FL1
1.00
Cu/Ag ionization
measures
1 2 3 4
TANK
D
After entering the "Node ID", press "Send" on screen Cand Escreen appears. Choose a password and press "Save".
E
Once the WIFI module is connected to the unit, with both lights on, and the connection to the network properly configured, enter www.vistapool.es.
Access the Register option (Figure B) and enter all the requested data. It is requested to enter the identity number of the pool, the "Node ID" (Figure C).
To obtain this number, access the “Power Module” screen in unit's TFT display (figure D). If the "Node ID" does not have the correct format, you can not
continue with the registration process. Please make sure you entered the corresponding 24 characters.
B
F
C
4VISTAPOOL WEBSITE OPERATION
If the swimming pool is properly communicating with the Vistapool central server, the screen Fwill be shown. If there is no communication with Vistapool
system, check the internet connection and network preferences (see chapter 2). The 2 green LEDs remain lit when the WIFI Module is connected properly.

4FUNCIONAMIENTO DE VISTAPOOL
H
G
If you want to change any parameter of your pool, select the eye icon () on the screen Fand then the "Configuration" tab (screen G). This screen depends
on the type of control pool that is installed on your system. Select the type of parameter to be adjusted, for example, to turn ON or OFF filtering, press the
"Man" button on the item "Filtration" and select "OFF" to stop the filtration process.
To access the pool statistics (screen H), select the icon of the chart (  Statistics). You can download the data to keep a history of your pool by clicking the
icon .
I
To add more pools to your profile, go to the home page by clicking on the Vistapool logo and select the list icon ( ), located above the box with
information about your pool. Screen Iappears, press the "New" button, fill out the form with the pool info and click "Save".
You can always change personal and pool data, delete pools and change preferences, pressing the button “ ” as seen on screen I.