Sullivan-Palatek 15D User manual
USER MANUAL
INDUSTRIAL ELECTRIC COMPRESSOR \ 15–40 HP \ D-SERIES
15D, H15D, 20D, H20D, HH20D
25D, HH25D, 25D4, H25D4
30D7, H30D7, HH30D7
40D, H40D, HH40D
ELECTRO-MECHANICAL CONTROLS
Document: 18730-049 / 00
Issued: June 30, 2017
DOCUMENT INFORMATION
© Sullivan-Palatek, Inc.
ALL RIGHTS RESERVED
Part Number: 18730-049
Revision: 00
CONTACT INFORMATION
Sullivan-Palatek, Inc.
1201 West US Highway 20
Michigan City, Indiana 46360
Phone: (219) 874-2497
Fax: (219) 872-5043
Toll Free: (800) 438-6203
Website: www.sullivan-palatek.com
RECORD KEEPING
Record the model and serial number of the compressor for future reference when contacting the Factory for service or parts.
Model Number:
Serial Number:
DISCLAIMER
Although this manual is checked for conformity with the machines described, we cannot guarantee that all errors will be excluded.
Necessary corrections will be made in future editions of this manual. This manual is subject to change without notice.
REVISION HISTORY
#DATE SECTION DESCRIPTION
00 2017-06-30 Released for publication
Sullivan-Palatek Industrial Air Compressor
STANDARD WARRANTY
(15hp and Larger Compressors)
Sullivan-Palatek warrants its new 15 horsepower and larger stationary industrial air compressor products to be free
from defects in material and workmanship and against loss of capacity due to wear, subject to the following provisions:
Warranty Duration: The warranty period for applicable Sullivan-Palatek products is as follows:
Compressor Package: 12 months from the date of start-up by an authorized distributor or 18 months from date of
24 months from the date of start-up
Parts Replaced Under Warranty:
Parts, Accessories and Attachments Sold Separately from Machines, Excluding Warranty Replacement Parts:
Registration and Obtaining Warranty Service: The purchaser, or authorized Sullivan-Palatek distributor on his
behalf, must complete and return the Warranty Registration Form within 10 days of start-up and before the end of
under this warranty is obtained by contacting the authorized Sullivan-Palatek distributor before the expiration of the
Sullivan-Palatek’s Obligations: Sullivan-Palatek will repair or replace, at Sullivan-Palatek’s option, any defective
part, pay the reasonable labor cost of making the repair or installing the replacement part, pay ground freight for the
Purchaser’s Responsibility: Performance of proper maintenance as indicated in the User Manual furnished with the
is also responsible for the following: the cost of normal maintenance and maintenance items, the consequences
of service performed by someone other than a party authorized to perform warranty service if such service, in
incurred in gaining access to the compressor such as overcoming barriers such as walls, fences or similar structures
Exclusions and Limitations: Electric motors, drives and dryers are not warranted by Sullivan-Palatek but are
or defects resulting from overloading, misuse, neglect, accident, failure to comply with Sullivan-Palatek’s product
THIS WARRANTY IS SULLIVAN-PALATEK’S ONLY WARRANTY OF ITS STATIONARY INDUSTRIAL AIR COMPRESSOR
PRODUCTS AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SULLIVAN-PALATEK HAS NO
INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOSS OF USE, LOST
PROFITS, LOST INCOME, WHETHER SUFFERED BY THE BUYER OR A THIRD PARTY. THE TOTAL RESPONSIBILITY OF
SULLIVAN-PALATEK FOR CLAIMS, LOSSES, LIABILITIES OR DAMAGES, WHETHER IN CONTRACT OR TORT ARISING
OUT OF OR RELATED TO ITS PRODUCTS SHALL NOT EXCEED THE PURCHASE PRICE OF THE COVERED PRODUCT.
This warranty applies to all Sullivan-Palatek stationary industrial air compressors of 15 horsepower and larger
11.12.15
Sullivan-Palatek Industrial Air Compressor
PLATINUM AND PLATINUM PLUS
EXTENDED WARRANTIES
(15hp and Larger Compressors)
purchaser of an industrial compressors of 15 horsepower and larger, excluding XH high pressure models designed
to operate at 250 psi or more. The Platinum Extended Warranty and the Platinum Plus Extended Warranty are
The terms, conditions and limitations contained in the
Sullivan-Palatek Standard Warranty apply to the Platinum Extended Warranty and the Platinum Plus Extended
Warranty and that warranty is herein incorporated by reference.
COMPONENT COVERAGE
Platinum Warranty: Coverage includes parts and labor to repair or replace, as deemed necessary solely by Sullivan-
Platinum Plus Warranty:
TOTAL PERIOD OF COVERAGE
Platinum Warranty: 60 months from the date of start-up as evidenced by the required Warranty Registration
Platinum Plus Warranty: 120 months from date of start-up as evidenced by the required Warranty Registration
The Platinum and Platinum Plus Extended Warranties are an extension of Sullivan-Palatek’s Standard Warranty and
Registration and Obtaining Warranty Service: The Warranty Registration Form supplied with the compressor must
be completed and returned within 10 days of delivery and start-up to register the compressor under the Platinum
can only be reestablished by application to Sullivan-Palatek’s Product Support department, which may require a paid
Sullivan-Palatek’s Obligations:
coverage includes labor, and will pay ground freight for the return of defective parts and shipment of replacement
Purchaser’s Responsibility: In addition to the responsibilities detailed in Sullivan-Palatek’s Standard Warranty,
the Platinum Extended Warranties require that the purchaser use Sullivan-Palatek brand compressor lubricant and
compliance with these terms must be available and invoices must be provided upon request in the event of a claim
This warranty applies to all Sullivan-Palatek stationary industrial air compressors of 15 horsepower or larger,
excluding XH models
V
I ABOUT THIS MANUAL
I.1 SAFETY INSTRUCTIONS
Instructions for the safe operation and maintenance of the Sullivan-Palatek air compressor are located
involved, described as follows:
WARNING! is used when death or personal injury could occur if the instruction is not followed.
CAUTION! is used when damage to property could occur if the instruction is not followed.
NOTE! is used to inform the reader of installation, operation or maintenance information that is important but not
hazardous.
I.2 MANUAL ORGANIZATION
Anyone operating or servicing the Sullivan-Palatek air compressor should read this entire manual and be
SECTION 1: INTRODUCTION
This section contains important basic information regarding the compressor, such as safety precautions and
SECTION 2: SPECIFICATIONS
SECTION 3: COMPONENT DESCRIPTION
SECTION 4: INSTALLATION
This section contains information and guidelines to follow when choosing a site for and installing the air
SECTION 5: OPERATION
This section contains an overview of the compressor controls, initial start-up procedures, and how to start
SECTION 6: MAINTENANCE
This section contains a maintenance schedule and step-by-step instructions for performing common
SECTION 7: TROUBLESHOOTING
SECTION 8: PARTS LISTING
This section contains procedures for ordering parts, a list of recommended spare parts to keep on hand, and
I.3 SUPPLEMENTAL DOCUMENTS
VI ABOUT THIS MANUAL
VII
II CONTENTS
I ABOUT THIS MANUAL................................................V
v
v
v
1 INTRODUCTION .....................................................1
2
2
3
2 SPECIFICATIONS.....................................................5
6
12
13
14
15
16
17
18
19
20
21
22
23
24
25
3 COMPONENT DESCRIPTION ..........................................27
28
28
28
28
29
30
31
36
4 INSTALLATION .....................................................37
38
38
38
38
38
39
39
39
40
40
40
5 OPERATION........................................................41
42
43
43
43
44
44
VIII CONTENTS
6 MAINTENANCE .....................................................45
46
47
47
47
48
49
51
52
53
53
53
54
7 TROUBLESHOOTING ................................................55
56
56
56
56
56
57
57
57
8 PARTS CATALOG ...................................................59
60
60
61
62
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
1
1 INTRODUCTION
TOPICS IN THIS SECTION:
» 2
» Safety Decals 2
» Screw Compressor Air End Exchange Program 3
2INTRODUCTION
1.1 GENERAL COMPRESSOR SAFETY PRECAUTIONS
machinery:
WARNING! Do not use air from this compressor for breathing, as it may contain colorless, odorless yet lethal gases.
Severe injury or death may result within a few seconds.
» Only trained and authorized personnel who have read and understand this user’s manual should operate
»
lockout the main power source to render it inoperative and tag the air compressor so others who may
» Use and operate the air compressor only in full compliance with all pertinent Federal, State and Local
»
»
»
» Keep all parts of the body away from all potential points of air discharge, including pressure relief valve
»
»
allow it!
»
»
»
» Wear OSHA approved personal protective gear including gloves, safety shoes, safety glasses, head
»
»
»
» Keep all parts of the body, tools or other conductive objects away from exposed live parts of the
Not all hazards can be anticipated, and the operator of the equipment is ultimately responsible for
1.2 SAFETY DECALS
Sullivan-Palatek compressors are all equipped with brightly colored, weather-resistant, pictorial/verbal
3INTRODUCTION
If any warning decals are missing, damaged, painted over or located in such a position as to be unreadable in
intended pictorial warnings, it becomes incumbent upon the owner, lessor or other responsible administrator
to be sure the operator is properly trained, made aware of and understands the meaning of all warning
1.3 SCREW COMPRESSOR AIR END EXCHANGE PROGRAM
4INTRODUCTION
5
2 SPECIFICATIONS
TOPICS IN THIS SECTION:
» Technical Data6
› 15D, H15D6
› 20D, H20D, HH20D 7
› 25D 8
› 25D4, H25D4, HH25D49
› 30D7, H30D7, HH30D7 10
› 40D, H40D, HH40D11
» 12
» 13
» 14
» 15
» 16
» 17
» 18
» 19
» 20
» 21
» 22
» 23
» 24
» 25
6SPECIFICATIONS
2.1 TECHNICAL DATA
2.1.1 15D, H15D
COMPRESSOR DATA 15D H15D
Capacity acfm 55 54
Pressure @ Full Load psig (bar) 125 (8.6) 150 (10.3)
Minimum Pressure psig (bar) 60 (4.1) 70 (4.8)
Motor Output (60 Hz) hp (kW) 15 (11.2) 15 (11.2)
Motor Speed rpm 1750 1,750
Motor Output @ Full Load hp (kW) 14 (10.4) 16 (11.9)
Motor Output @ 100 psig hp (kW) 13 (9.7)
Driven Rotor Coupling Direct Direct
Drive Ratio 1 1
Rotor Diameter mm 108 108
COOLING DATA (AIR-COOLED) 15D H15D
Fan Airow cfm 1,000 1,000
Maximum Duct Loss inH2O0.3 0.3
Aercooler Approach °F (°C) 12 (-11) 12 (-11)
Heat Rejection btu/hr (kW) 34,700 (10.2) 34,700 (10.2)
Fluid Capacity gallons (liters) 3 (11) 3 (11)
COOLING DATA (WATER-COOLED) 15D H15D
Water Flow with 60°F Water gpm (L/min) 1.5 (5.7) 1.5 (5.7)
Water Flow with 70°F Water gpm (L/min) 1.9 (7.2) 1.9 (7.2)
Water Flow with 80°F Water gpm (L/min) 2.5 (9.5) 2.5 (9.5)
Maximum Water Temperature °F (°C) 85 (29) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4 3/4 - 3/4
SOUND DATA 15D H15D
Air-Cooled (Open) dba @ 1m 75 75
Air-Cooled (Enclosed) dba @ 1m 68 68
Water-Cooled (Open) dba @ 1m 72 72
Water-Cooled (Enclosed) dba @ 1m 72 72
DISCHARGE PIPING 15D H15D
Air-Cooled (Base-Mounted) NPT 1 1
Water-Cooled (Base-Mounted) NPT 1 1
Tank-Mounted (Tank End) NPT 2 2
ELECTRICAL DATA 15D H15D
Motor FLA @ 575V amps 15.4 15.4
Motor FLA @ 460V amps 19.2 19.2
Motor FLA @ 230V amps 38.4 38.4
Motor FLA @ 208V amps 42.7 42.7
Motor FLA @ 200V amps 44.2 44.2
Starter Enclosure Rating NEMA 1 1
Control Voltage volts 110 110
Motor Enclosure NEMA ODP ODP
Motor Insulation Class NEMA F F
Motor Service Factor NEMA 1.25 1.25
Motor Maximum Starts/Hour 4 4
7SPECIFICATIONS
2.1.2 20D, H20D, HH20D
COMPRESSOR DATA 20D H20D HH20D
Capacity acfm 80 78 53
Pressure @ Full Load psig (bar) 125 (8.6) 150 (10.3) 175 (12.1)
Minimum Pressure psig (bar) 60 (4.1) 70 (4.8) 70 (4.8)
Motor Output (60 Hz) hp (kW) 20 (14.9) 20 (14.9) 20 (14.9)
Motor Speed rpm 1,750 1,750 1,750
Motor Output @ Full Load hp (kW) 21.5 (16.0) 19 (14.2) 20 (14.9)
Motor Output @ 100 psig hp (kW) 19.1 (14.2)
Driven Rotor Coupling Direct Direct Direct
Drive Ratio 111
Rotor Diameter mm 108 108 108
COOLING DATA (AIR-COOLED) 20D H20D HH20D
Fan Airow cfm 2,200 2,200 2,200
Maximum Duct Loss inH2O0.3 0.3 0.3
Aercooler Approach °F (°C) 12 (-11) 12 (-11) 12 (-11)
Heat Rejection btu/hr (kW) 51,600 (15.1) 51,600 (15.1) 51,600 (15.1)
Fluid Capacity gallons (liters) 3 (11) 3 (11) 3 (11)
COOLING DATA (WATER-COOLED) 20D H20D HH20D
Water Flow with 60°F Water gpm (L/min) 2.3 (8.7) 2.3 (8.7) 2.3 (8.7)
Water Flow with 70°F Water gpm (L/min) 2.9 (11.0) 2.9 (11.0) 2.9 (11.0)
Water Flow with 80°F Water gpm (L/min) 3.8 (14.4) 3.8 (14.4) 3.8 (14.4)
Maximum Water Temperature °F (°C) 85 (29) 85 (29) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4 3/4 - 3/4 3/4 - 3/4
SOUND DATA 20D H20D HH20D
Air-Cooled (Open) dba @ 1m 75 75 75
Air-Cooled (Enclosed) dba @ 1m 68 68 68
Water-Cooled (Open) dba @ 1m 73 73 73
Water-Cooled (Enclosed) dba @ 1m 73 73 73
DISCHARGE PIPING 20D H20D HH20D
Air-Cooled (Base-Mounted) NPT 1 1 1
Water-Cooled (Base-Mounted) NPT 1 1 1
Tank-Mounted (Tank End) NPT 2 2 2
ELECTRICAL DATA 20D H20D HH20D
Motor FLA @ 575V amps 20.8 20.8 20.8
Motor FLA @ 460V amps 26.0 26.0 26.0
Motor FLA @ 230V amps 52.0 52.0 52.0
Motor FLA @ 208V amps 57.5 57.5 57.5
Motor FLA @ 200V amps 59.8 59.8 59.8
Starter Enclosure Rating NEMA 1 1 1
Control Voltage volts 110 110 110
Motor Enclosure NEMA ODP ODP ODP
Motor Insulation Class NEMA F F F
Motor Service Factor NEMA 1.25 1.25 1.25
Motor Maximum Starts/Hour 4 4 4
8SPECIFICATIONS
2.1.3 25D
COMPRESSOR DATA 25D
Capacity acfm 110
Pressure @ Full Load psig (bar) 125 (8.6)
Minimum Pressure psig (bar) 60 (4.1)
Motor Output (60 Hz) hp (kW) 25 (18.6)
Motor Speed rpm 3,550
Motor Output @ Full Load hp (kW) 27 (20.1)
Motor Output @ 100 psig hp (kW) 24 (17.9)
Driven Rotor Coupling Direct
Drive Ratio 1
Rotor Diameter mm 108
COOLING DATA (AIR-COOLED) 25D
Fan Airow cfm 2,600
Maximum Duct Loss inH2O0.25
Aercooler Approach °F (°C) 15 (-9)
Heat Rejection btu/hr (kW) 68,500 (20.1)
Fluid Capacity gallons (liters) 3 (11)
COOLING DATA (WATER-COOLED) 25D
Water Flow with 60°F Water gpm (L/min) 3 (11.4)
Water Flow with 70°F Water gpm (L/min) 3.7 (14.0)
Water Flow with 80°F Water gpm (L/min) 5 (18.9)
Maximum Water Temperature °F (°C) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4
SOUND DATA 25D
Air-Cooled (Open) dba @ 1m 85
Air-Cooled (Enclosed) dba @ 1m 75
Water-Cooled (Open) dba @ 1m 80
Water-Cooled (Enclosed) dba @ 1m 80
DISCHARGE PIPING 25D
Air-Cooled (Base-Mounted) NPT 1
Water-Cooled (Base-Mounted) NPT 1-1/2
Tank-Mounted (Tank End) NPT 2
ELECTRICAL DATA 25D
Motor FLA @ 575V amps 23.2
Motor FLA @ 460V amps 29.0
Motor FLA @ 230V amps 58.0
Motor FLA @ 208V amps 64.1
Motor FLA @ 200V amps 66.7
Starter Enclosure Rating NEMA 1
Control Voltage volts 110
Motor Enclosure NEMA ODP
Motor Insulation Class NEMA F
Motor Service Factor NEMA 1.25
Motor Maximum Starts/Hour 4
9SPECIFICATIONS
2.1.4 25D4, H25D4, HH25D4
COMPRESSOR DATA 25D4 H25D4 HH25D4
Capacity acfm 95 90 78
Pressure @ Full Load psig (bar) 125 (8.6) 150 (10.3) 175 (12.1)
Minimum Pressure psig (bar) 60 (4.1) 70 (4.8) 70 (4.8)
Motor Output (60 Hz) hp (kW) 25 (18.6) 25 (18.6) 25 (18.6)
Motor Speed rpm 1,750 1,750 1,750
Motor Output @ Full Load hp (kW) 25 (18.6) 27 (20.1) 27 (20.1)
Motor Output @ 100 psig hp (kW) 22.2 (16.6)
Driven Rotor Coupling Direct Direct Direct
Drive Ratio 1 1 1
Rotor Diameter mm 108 108 108
COOLING DATA (AIR-COOLED) 25D4 H25D4 HH25D4
Fan Airow cfm 2,250 2,250 2,250
Maximum Duct Loss inH2O0.25 0.25 0.25
Aercooler Approach °F (°C) 15 (-9) 15 (-9) 15 (-9)
Heat Rejection btu/hr (kW) 59,200 (17.3) 59,200 (17.3) 59,20 0 (17.3)
Fluid Capacity gallons (liters) 3 (11) 3 (11) 3 (11)
COOLING DATA (WATER-COOLED) 25D4 H25D4 HH25D4
Water Flow with 60°F Water gpm (L/min) 3 (11.4) 3 (11.4) 3 (11.4)
Water Flow with 70°F Water gpm (L/min) 3.7 (14.0) 3.7 (14.0) 3.7 (14.0)
Water Flow with 80°F Water gpm (L/min) 5 (18.9) 5 (18.9) 5 (18.9)
Maximum Water Temperature °F (°C) 85 (29) 85 (29) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4 3/4 - 3/4 3/4 - 3/4
SOUND DATA 25D4 H25D4 HH25D4
Air-Cooled (Open) dba @ 1m 75 75 75
Air-Cooled (Enclosed) dba @ 1m 68 68 68
Water-Cooled (Open) dba @ 1m 73 73 73
Water-Cooled (Enclosed) dba @ 1m 73 73 73
DISCHARGE PIPING 25D4 H25D4 HH25D4
Air-Cooled (Base-Mounted) NPT 1 1 1
Water-Cooled (Base-Mounted) NPT 1-1/2 1-1/2 1-1/2
Tank-Mounted (Tank End) NPT 2 2 2
ELECTRICAL DATA 25D4 H25D4 HH25D4
Motor FLA @ 575V amps 27.2 27.2 27.2
Motor FLA @ 460V amps 34.0 34.0 34.0
Motor FLA @ 230V amps 68.0 68.0 68.0
Motor FLA @ 208V amps 75.2 75.2 75.2
Motor FLA @ 200V amps 8 7.5 87.5 87.5
Starter Enclosure Rating NEMA 1 1 1
Control Voltage volts 110 110 110
Motor Enclosure NEMA ODP ODP ODP
Motor Insulation Class NEMA FFF
Motor Service Factor NEMA 1.25 1.25 1.25
Motor Maximum Starts/Hour 4 4 4
10 SPECIFICATIONS
2.1.5 30D7, H30D7, HH30D7
COMPRESSOR DATA 30D7 H30D7 HH30D7
Capacity acfm 115 110 105
Pressure @ Full Load psig (bar) 125 (8.6) 150 (10.3) 175 (12.1)
Minimum Pressure psig (bar) 60 (4.1) 70 (4.8) 70 (4.8)
Motor Output (60 Hz) hp (kW) 30 (22.4) 30 (22.4) 30 (22.4)
Motor Speed rpm 3,550 3,550 3,550
Motor Output @ Full Load hp (kW) 30 (22.4) 30 (22.4) 33 (24.6)
Motor Output @ 100 psig hp (kW) 28 (20.9)
Driven Rotor Coupling Direct Direct Direct
Drive Ratio 111
Rotor Diameter mm 108 108 108
COOLING DATA (AIR-COOLED) 30D7 H30D7 HH30D7
Fan Airow cfm 2,600 2,600 2,600
Maximum Duct Loss inH2O0.25 0.25 0.25
Aercooler Approach °F (°C) 15 (-9) 15 (-9) 15 (-9)
Heat Rejection btu/hr (kW) 71,600 (21.0) 71,600 (21.0) 71,600 (21.0)
Fluid Capacity gallons (liters) 3 (11) 3 (11) 3 (11)
COOLING DATA (WATER-COOLED) 30D7 H30D7 HH30D7
Water Flow with 60°F Water gpm (L/min) 3 (11.4) 3 (11.4) 3 (11.4)
Water Flow with 70°F Water gpm (L/min) 3.7 (14.0) 3.7 (14.0) 3.7 (14.0)
Water Flow with 80°F Water gpm (L/min) 5 (18.9) 5 (18.9) 5 (18.9)
Maximum Water Temperature °F (°C) 85 (29) 85 (29) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4 3/4 - 3/4 3/4 - 3/4
SOUND DATA 30D7 H30D7 HH30D7
Air-Cooled (Open) dba @ 1m 85 85 85
Air-Cooled (Enclosed) dba @ 1m 75 75 75
Water-Cooled (Open) dba @ 1m 80 80 80
Water-Cooled (Enclosed) dba @ 1m 80 80 80
DISCHARGE PIPING 30D7 H30D7 HH30D7
Air-Cooled (Base-Mounted) NPT 111
Water-Cooled (Base-Mounted) NPT 1-1/2 1-1/2 1-1/2
Tank-Mounted (Tank End) NPT 222
ELECTRICAL DATA 30D7 H30D7 HH30D7
Motor FLA @ 575V amps 28.0 28 28.0
Motor FLA @ 460V amps 35.0 35.0 35.0
Motor FLA @ 230V amps 70.0 70.0 70.0
Motor FLA @ 208V amps 77.4 77.4 77.4
Motor FLA @ 200V amps 89.0 89 89.0
Starter Enclosure Rating NEMA 1 1 1
Control Voltage volts 110 110 110
Motor Enclosure NEMA ODP ODP ODP
Motor Insulation Class NEMA FFF
Motor Service Factor NEMA 1.25 1.25 1.25
Motor Maximum Starts/Hour 4 4 4
11SPECIFICATIONS
2.1.6 40D, H40D, HH40D
COMPRESSOR DATA 40D H40D HH40D
Capacity acfm 166 115 110
Pressure @ Full Load psig (bar) 125 (8.6) 150 (10.3) 175 (12.1)
Minimum Pressure psig (bar) 60 (4.1) 70 (4.8) 70 (4.8)
Motor Output (60 Hz) hp (kW) 40 (29.8) 40 (29.8) 40 (29.8)
Motor Speed rpm 3,550 3,550 3,550
Motor Output @ Full Load hp (kW) 47 (35.0) 41 (30.6) 43 (32.1)
Motor Output @ 100 psig hp (kW) 42 (31.3)
Driven Rotor Coupling Direct Direct Direct
Drive Ratio 1 1 1
Rotor Diameter mm 108 108 108
COOLING DATA (AIR-COOLED) 40D H40D HH40D
Fan Airow cfm 3,500 3,500 3,500
Maximum Duct Loss inH2O0.25 0.25 0.25
Aercooler Approach °F (°C) 15 (-9) 15 (-9) 15 (-9)
Heat Rejection btu/hr (kW) 106,300 (31.1) 106,300 (31.1) 106,300 (31.1)
Fluid Capacity gallons (liters) 3.5 (13) 3.5 (13) 3.5 (13)
COOLING DATA (WATER-COOLED) 40D H40D HH40D
Water Flow with 60°F Water gpm (L/min) 4.5 (17.0) 4. 5 (17.0) 4.5 (17.0)
Water Flow with 70°F Water gpm (L/min) 5.8 (21.0) 5.8 (21.0) 5.8 (21.0)
Water Flow with 80°F Water gpm (L/min) 7.6 (28.8) 7.6 (28.8) 7.6 (28.8)
Maximum Water Temperature °F (°C) 85 (29) 85 (29) 85 (29)
Water Connection In-Out NPT 3/4 - 3/4 3/4 - 3/4 3/4 - 3/4
SOUND DATA 40D H40D HH40D
Air-Cooled (Open) dba @ 1m 85 85 85
Air-Cooled (Enclosed) dba @ 1m 80 80 80
Water-Cooled (Open) dba @ 1m 80 80 80
Water-Cooled (Enclosed) dba @ 1m 80 80 80
DISCHARGE PIPING 40D H40D HH40D
Air-Cooled (Base-Mounted) NPT 1-1/4 1-1/4 1-1/4
Water-Cooled (Base-Mounted) NPT 1-1/2 1-1/2 1-1/2
Tank-Mounted (Tank End) NPT 2 2 2
ELECTRICAL DATA 40D H40D HH40D
Motor FLA @ 575V amps 36.0 36 36.0
Motor FLA @ 460V amps 45.0 45.0 45.0
Motor FLA @ 230V amps 90.0 90.0 90.0
Motor FLA @ 208V amps 99.5 99.5 99.5
Motor FLA @ 200V amps 102.0 102 102.0
Starter Enclosure Rating NEMA 1 1 1
Control Voltage volts 110 110 110
Motor Enclosure NEMA ODP ODP ODP
Motor Insulation Class NEMA FFF
Motor Service Factor NEMA 1.25 1.25 1.25
Motor Maximum Starts/Hour 4 4 4
12 SPECIFICATIONS
2.2 DIMENSIONS–OPEN, BASE MOUNT, AIR-COOLED
This manual suits for next models
14
Table of contents
Other Sullivan-Palatek Air Compressor manuals
Sullivan-Palatek
Sullivan-Palatek D185PIZP Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D185PKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D210PHKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek UD Series User manual
Sullivan-Palatek
Sullivan-Palatek D110PKUW User manual
Sullivan-Palatek
Sullivan-Palatek D110PKU User manual
Sullivan-Palatek
Sullivan-Palatek DC185P3JD User manual
Sullivan-Palatek
Sullivan-Palatek D260PDKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D185UIZ Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek VFD Series User manual
Popular Air Compressor manuals by other brands
Vixen Air
Vixen Air VXC480B installation guide
Chicago Pneumatic
Chicago Pneumatic HP 20 Use & maintenance manual
AllTrade
AllTrade Air-Plus 540025 instruction manual
Kyocera
Kyocera TJEP 17/15-2 Safety and operation instructions
Porter-Cable
Porter-Cable C5512 instruction manual
Danfoss
Danfoss Vitrifrigo BD50F instructions
