Sullivan-Palatek D260UJD4PTOW User manual
USER MANUAL
UTILITY COMPRESSOR \ PTO AUXILIARY DRIVE \ 260 CFM
D260UJD4PTOW
JOHN DEERE DIESEL ENGINE
TIER 4 FINAL
05018730 0242 / 00
Issued: July 09, 2018
DOCUMENT INFORMATION
© Sullivan-Palatek, Inc.
ALL RIGHTS RESERVED
Part Number: 05018730 0242
Revision: 00
CONTACT INFORMATION
Sullivan-Palatek, Inc.
1201 West US Highway 20
Michigan City, Indiana 46360
Phone: (219) 874-2497
Fax: (219) 872-5043
Toll Free: (800) 438-6203
Website: www.sullivan-palatek.com
RECORD KEEPING
Record the model and serial number of the compressor for
future reference when contacting the factory for service
or parts.
Model Number:
Serial Number:
DISCLAIMER
Although this manual is checked for conformity with the machines
described, we cannot guarantee that all errors will be excluded.
Necessary corrections will be made in future editions of this manual.
This manual is subject to change without notice.
REVISION HISTORY
#DATE SECTION(S) DESCRIPTION
00 2018-07-09 Released for publication
Sullivan-Palatek Portable Air Compressor
STANDARD WARRANTY
Sullivan-Palatek warrants its new portable air compressor products to be free from defects in material and
workmanship, subject to the following provisions:
Warranty Registration: To validate the warranty for each product the purchaser shall complete and return the
Warranty Period: The warranty period for applicable Sullivan-Palatek products is as follows (subject to the
Exclusions and Limitations noted below):
Air ends on new machines – stator and rotor assembly: Single stage
Two stage high pressure
Remainder of new portable air compressor machines:
Parts, accessories and attachments sold separately from machines, excluding warranty replacement parts
and hand tools:
Warranty replacement parts:
Sullivan-Palatek’s Obligations: Sullivan-Palatek’s exclusive obligations under its warranty are (i) to repair or
replace any defective part at Sullivan-Palatek’s option and subject to return of defective parts, (ii) to pay the
reasonable cost of making the repair or reinstalling the replacement part, and (iii) for air compressors having two or
more axles, reimbursement of up to four hours travel labor and up to 200 miles (100 miles travel radius) per event
Purchaser’s Responsibility: Purchaser shall (i) give Sullivan-Palatek written notice of any warrantable failure of
any Sullivan-Palatek product within the applicable warranty period, (ii) make the product available for repair at a
Sullivan-Palatek authorized repair facility, (iii) pay all costs of returning failed parts to Sullivan-Palatek, (iv) pay
Exclusions and Limitations:
obligation for product failures or defects resulting from overloading, misuse, neglect, accident, failure to comply
Use of attachments, accessories or service parts not supplied or recommended by Sullivan-Palatek may void the
THIS WARRANTY IS SULLIVAN-PALATEK’S ONLY WARRANTY OF ITS PORTABLE AIR COMPRESSOR PRODUCTS
AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SULLIVAN-PALATEK HAS NO
OBLIGATION UNDER THIS WARRANTY OR OTHERWISE (REGARDLESS OF THE FORM OF ACTION) FOR SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS OR LOST INCOME.
THE TOTAL RESPONSIBILITY OF SULLIVAN-PALATEK FOR CLAIMS, LOSSES, LIABILITIES OR DAMAGES, WHETHER
IN CONTRACT OR TORT ARISING OUT OF OR RELATED TO ITS PRODUCTS SHALL NOT EXCEED THE PURCHASE
PRICE OF THE COVERED PRODUCT.
V
I AbOUT THIS MANUAL
I.1 SAFETY INSTRUCTIONS
Instructions for the safe operation and maintenance of the Sullivan-Palatek air compressor are located
WARNING! is used when death or personal injury could occur if the instruction is not followed.
CAUTION! is used when damage to property could occur if the instruction is not followed.
NOTE! is used to inform the reader of installation, operation or maintenance information that is important but not
hazardous.
I.2 MANUAL ORGANIZATION
NOTE! Anyone operating or servicing the Sullivan-Palatek air compressor should read this entire manual and be
familiar with its information. The following is a quick guide to the contents in this manual:
SECTION 1: SAFETY
This section contains important basic information regarding general safety precautions for maintaining and
SECTION 2: SPECIFICATIONS
SECTION 3: COMPONENT DESCRIPTION
SECTION 4: INSTALLATION AND OPERATION
SECTION 5: MAINTENANCE
This section contains a maintenance schedule and step-by-step instructions for performing common
SECTION 6: TROUbLESHOOTING
SECTION 7: PARTS CATALOG
This section contains procedures for ordering parts, a list of recommended spare parts to keep on hand, and
I.3 SUPPLEMENTAL DOCUMENTS
VI
VII
II CONTENTS
I AbOUT THIS MANUAL � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � V
v
v
v
1 SAFETY � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
2
2
2
3
4
4
4
5
2 SPECIFICATIONS � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
8
9
10
11
12
13
3 COMPONENT DESCRIPTION � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15
16
16
16
16
17
18
19
19
19
20
21
23
4 INSTALLATION & OPERATION � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 25
26
26
26
26
27
27
27
28
30
33
34
35
VIII
5 MAINTENANCE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 37
38
39
39
™Compressor Lubricant40
41
42
42
42
42
43
43
43
44
44
44
44
6 TROUbLESHOOTING� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 45
46
46
46
47
47
47
47
47
48
48
48
48
49
7 PARTS CATALOG � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 51
52
52
52
53
53
54
62
64
68
70
72
74
78
80
82
86
90
96
102
106
118
122
124
1
1 SAFETY
TOPICS IN THIS SECTION:
» 2
» Pressure Release 2
» Fires and Explosion 2
» Moving Parts 3
» Toxic and Irritating Substances 4
» 4
» Electrical Shock 4
» Entrapment 5
CALIFORNIA
PROPOSITION 65 WARNING
constituents are known to the State
of California to cause cancer, birth
2SAFETY
1.1 GENERAL SAFETY
machinery:
» Only trained and authorized personnel who have read and understand this user’s manual should operate
»
compressor and render it inoperative by disconnecting the battery so others who may not know of the
» Use and operate the air compressor only in full compliance with all pertinent Federal, State and Local
»
»
is ultimately responsible for identifying hazardous and dangerous conditions, avoiding dangerous
1.2 PRESSURE RELEASE
»
»
»
»
»
the coolant temperature is below its boiling point, then loosen cap slowly to its stop to relieve any
1.3 FIRES AND EXPLOSION
1.3.1 FUEL & LIQUIDS
WARNING! Fire or explosion can result from spilled fuel, oil and other ammable liquids.
»
»
»
»
»
3SAFETY
»
»
1.3.2 BATTERIES AND WIRING
WARNING! Fire or explosion can result from electrical arcing from terminal, battery connections and improperly
grounded equipment.
»
»
»
»
»
»
»
1.3.3 COMBUSTIBLES
» Prior to welding or making weld repairs on the compressor, remove any acoustical material or other
»
»
»
»
1.4 MOVING PARTS
»
»
»
»
walking surfaces clean and free of oil, water, anti-freeze, or other liquids to minimize the possibility of
»
doors closed except when repairing, adjusting or performing service, or when starting or stopping the
» Shut down engine before servicing, especially when adding fuel, oil, coolant, lubricants, airline
4SAFETY
1.5 TOXIC AND IRRITATING SUBSTANCES
WARNING! Do not use air from this compressor for breathing air. Breathing unltered air from this compressor can
result in serious injury or death.
NOTE! Under specic guidelines and in full compliance with OSHA Standards 29 CFR 1920 and any other federal,
state, or local codes or regulations compressed air can be used for breathing air. Sullivan-Palatek does
not provide equipment and instructions for this application and its products are not produced for this
application or use.
»
»
» Locate the compressor so that exhaust will not be carried toward personnel, air intakes servicing
»
»
»
» The
anti-freeze compound used in airline anti-icing systems contains methanol and is toxic, harmful, or
clean, warm water until vomit is clear, then administer two teaspoons of baking soda in a glass of clean
» airline anti-icing system anti-freeze compound in operator’s cabs or in unapproved
»
1.6 HOT SURFACES, SHARP EDGES, SHARP CORNERS AND VACUUM
»
»
» Wear personal protective equipment, including gloves, safety glasses and head covering when working
»
»
1.7 ELECTRICAL SHOCK
»
»
contact any other portion of the compressor when making adjustments or repairs to exposed live parts
5SAFETY
1.8 ENTRAPMENT
»
secure the access door in the open position to avoid the possibility of others closing and latching the
6SAFETY
7
2 SPECIFICATIONS
TOPICS IN THIS SECTION:
» 8
» 9
»10
»11
»12
»13
8
2.1 TECHNICAL DATA
D260UJD4PTO
COMPRESSOR
Type Single Stage, Oil Flooded Rotary Screw
Rated Delivery 260 cfm (7.4 m/min)
Rated Operating Pressure 100 psig (6.9 bar)
Rated Operating Pressure Range 70–125 psig (4.9–8.6 bar)
Ambient Temperature Range -20 to +125°F (-29 to +52°C)
Oil Capacity 7.9 gallons (30 L)
Total Receiver Volume 3 (48 L)
Air Service Connector Two 3/4-in NPT
Type Cooling System Oil to Air
Type Air Intake System 2-Stage Dry
Type of Control 0–100% Demand
Noise Level 76 dBA @ 7 meters
Estimated Weight, Serviced 3070 lbs (1393 kg)
Dimensions L x W x H 83 x 35 x 55.39 inches (2108 x 889 x 1407 mm)
ENGINE
Type Diesel Tier 4
Engine Make John Deere
Engine Model 4045TFCO3A, B (Tier 4 Final)
Number of Cylinders 4
Bore and Stroke 4.19 × 5.0 in (106 × 127 mm)
Displacement 276 in3 (4.5 L)
Horsepower @ Rated RPM 74 hp (55.5 kW)
Total Oil Capacity 9 quarts (8.5 L)
Cooling System Capacity 14 quarts (13.2 L)
Battery Rating Volts 12 volts
Cold Cranking Amps @ 0°F (-18°C) 800 amps
Full Load Speed 2500 rpm
Idle Speed 1600 rpm
Fuel Tank Capacity 35 gallons (132 L)
9
2.2 DIMENSIONAL DRAWING
35.18in
893.46mm
58.68in
1490.50mm
50.58in
1284.66mm
36.43in
925.26mm
6.81in
173.05mm
54.84in
1392.92mm
83.00in
2108.20mm
8.62in
218.88mm
5.24in
133.21mm
.32in
8.24mm
.44in
11.16mm
37.74in
958.58mm
30.61in
777.54mm
83.76in
2127.61mm
SERVICE
CONNECTION
FUEL
FILL
LIFTING BAIL
EXHAUST
35.00in
889mm
6.88in
174.63mm
2.07in
52.57mm
9.48in
240.85mm
85.07in
2160.80mm
17.57in
446.37mm
3.00in
76.20mm
AIR
FILTERS
FUEL
FILTER
COMPRESSOR
OIL FILTER
COMPRESSOR
OIL FILL & SIGHTGLASS
INSTRUMENT
PANEL
FUEL WATER
SEPARATOR
FUEL
FILL
79.00in
2006.60mm
2.00in
50.80mm
4.26in
108.29mm
26.63in
676.28mm
18.30in
464.80mm
4x
.75in
19.05mm
4.68in
118.99mm
2.84in
72.12mm
REMOVEABLE SIDE DOOR
(BOTH SIDS OF MACHINE)
INSTRUMENT
PANEL DOOR
FILTER
ACCESS
DOOR
RECEIVER TANK
ACCESS
RADIATOR
ACCESS
1:6
D260UJD4:
ESTIMATED WEIGHT:
3070 lbs (1393 kg)
SCREW COMPRESSOR:
0-100 % DEMAND OF
260 CFM @ 100 PSI (LOW)
AMBIENT TEMP RANGE:
-20
F(-29
C) TO 125
F(52
C)
JOHN DEERE ENGINE:
4045TFC03A
74 HP (55.2kW)
IDLE SPEED: 1600rpm
FULL LOAD SPEED: 2500rpm
REVISIONS
REV.
DESCRIPTION
ECN # DATE
APPROVED
00
RELEASED FOR PRODUCTION
15528 11/29/17 JDS/JW
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
E
JDS
FIRST USED ON:
3RD ANGLE
PROJECTION
1201 West US Highway 20, Michigan City IN 46360
1-800-438-6203
SHEET
SCALE:
TOLERANCES AS FOLLOWS:
REV
DESCRIPTION
THIS DRAWING AND ALL INFORMATION THEREIN IS THE PROPERTY OF SULLIVAN-PALATEK, INC. IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED.
WWW.SULLIVANPALATEK.COM
SULLIVAN-PALATEK
CHECKED BY:
DATE:
DATE:
DRAWN BY:
ANGLES: + OR - 1/2 DEG.
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE NOTED
X.XXX + OR - 0.005
X.XX + OR - 0.020
DECIMAL: X.X + OR - 0.050
MATERIAL:
IT IS LOANED SUBJECT TO RETURN UPON DEMAND, IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANYWAY DETRIMENTAL TO SULLIVAN-PALATEK'S INTEREST.
DRAWING NO:
SIZE
1 OF 1
D260UJD4
JW
11/29/17
11/29/17
00
GA 00007
D260UJD4
GERNERAL ARRANGEMENT,
10
2.3 SCHEMATIC DIAGRAM
ECU
CTC [B-P]
CTC [A-P]
CTC [C-P]
JDL [E-P]
JDL [C-P]
JDL [D-P]
E3 [44-P]
E3 [43-P]
E3 [27-P]
E3 [21-P]
E3 [7-P]
E3 [2-P]
E3 [1-P]
FUSES
W/HOLDER
25
4
1
6
3
CDC [D-P]
CDC [E-P]
CDC [A-P]
CDC [B-P]
NOTES:
1.DASHED LINES INDICATE CONNECTOR
W/ MULTIPLE PIN CONNECTIONS.
2.[ _-P] REPRESENTS WHAT PIN NUMBER
THE WIRE IS GOING TO.
3. OPEN CIRCLES REPRESENT SPLICES,
& AN ELLIPSE W/ 3 WIRES CONNECTED
REPRESENTS A TWISTED PAIR W/ A DRAIN.
4. E3 IS THE ENGINE ECU CONNECTOR FOR THIS
HARNESS. E1 & E2 COME WITH THE ENGINE.
5.M35 IS THE MURPHY 35-PIN CONNECTOR
& IT PLUGS INTO THE BACK OF THE
MURPHY DISPLAY.
6. CDC IS THE CAN DIAGNOSTICS PLUG. CTC IS
THE CAN TERMINATOR CONNECTOR, WHICH
PLUGS INTO A PREPINNED RECEPTACLE.
7.JDL REPRESENTS THE JOHN DEERE LINK
WHICH GIVES THE OPTION OF REMOTE
PROGRAMMING WITH ADDITIONAL
JD LINK HARNESS.
8.2-PIN JUMPER "A" PLUGS INTO 2-PIN JUMPER "B".
9. ALL RING TERMINALS ARE #3/8 STUDS THAT
CONNECT TO THE BATTERY. THE REST OF THE
RING TERMINALS ARE #10 STUDS UNLESS
NOTED OTHERWISE.
1
2
-
+
START
IGNITION
BATTERY
NTS
CAN LO
CAN HI
CAN SHIELD
ECU POWER
ECU POWER
ECU POWER
ECU POWER
KEYSWITCH
ECU GROUND
ECU GROUND
ECU GROUND
E1 E2 E3
E3
CDC
E3
JDL
M35
35-PIN MURPHY
CONNECTOR
JD LINK
CAN
DIAGNOSTIC
CONNECTOR
POWER
GROUND
GROUND
CAN HI
CAN SHIELD
CAN LO
ALT. EXCIT.
CAN SHIELD
IGNITION
CAN HI
CAN LO
POWER
TRANSDUCER
TEMP SENDER
FUEL SENDER
USB VBUS
USB D (+)
USB SHIELD
USB ID
USB D(-)
GROUND
POWER
CAN LO
CAN HI
CAN SHIELD
DEUTSCH USB
CONNECTOR
USB VBUS
USB SHIELD
USB D (+)
USB ID
USB D(-)
USB
USB [3-P]
USB [6-P]
USB [5-P]
USB [2-P]
USB [1-P]
M35 [25-P]
M35 [24-P]
M35 [13-P]
M35 [2-P]
M35 [1-P]
CONNECT
M35 [8-P]
M35 [20-P]
B A
B A
ALTERNATOR
EXCITATION
INTCON
JDL [G-P]
[1-P]
M35 [29-P]
M35 [14-P]
M35 [26-P]
CTC
CAN
TERMINATOR
CONNECTOR
CAN SHIELD
CAN HI
CAN LO
M35 [28-P]
M35 [27-P]
CDC [C-P]
M35 [14-P]
E3 [13-P]
E3 [14-P]
E3 [23-P]
E3 [24-P]
JDL [F-P]
JDL [J-P]
JDL [H-P]
12V BATTERY
DISCHARGE
TEMP.
SENDER
STARTER
SOLENOID
IGNITION
SWITCH
20 A
10 A
10 A
-
-
++++
FUEL
SENDER
PRESSURE
TRANSDUCER
2-PIN
JUMPER A
2-PIN
JUMPER B
GRND
PWR
PWR
PWR
PWR
GRND
GRND
PWR
PWR
PWR
PWR
PWR
GRND
GRND
GRND
PRESSURE SIGNAL
1
2
3
5
AB
CD
E
F
5
4
3
2
1
F
E
D
C
B
A
4
B
JDS
FIRST USED ON:
3RD ANGLE
PROJECTION
1201 West US Highway 20, Michigan City IN 46360
1-800-438-6203
SHEET
SCALE:
TOLERANCES AS FOLLOWS:
REV
DESCRIPTION
THIS DRAWING AND ALL INFORMATION THEREIN IS THE PROPERTY OF SULLIVAN-PALATEK, INC. IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED.
WWW.SULLIVANPALATEK.COM
SULLIVAN-PALATEK
CHECKED BY:
DATE:
DATE:
DRAWN BY:
ANGLES: + OR - 1/2 DEG.
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE NOTED
X.XXX + OR - 0.005
X.XX + OR - 0.020
DECIMAL: X.X + OR - 0.050
MATERIAL:
IT IS LOANED SUBJECT TO RETURN UPON DEMAND, IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANYWAY DETRIMENTAL TO SULLIVAN-PALATEK'S INTEREST.
DRAWING NO:
SIZE
1 OF 1
D210UHJD4
8/30/15
01
SD 1002
D210UHJD4 JD 4045TFC03 T4F
SCHEMATIC DIAGRAM
11
2.4 WIRING DIAGRAM
A
B
C
BATTERY
+
ST.
IGN
BATT.
16
52
34
SPLICE
SPLICE
SPLICE
5A FUSE
W/HOLDER
10A FUSE
W/HOLDER
20A FUSE
W/HOLDER
NOTES:
1.THE THREE O-RING TERMINALS ON THE IGNITION
SWITCH ARE # 10 STUDS. ALL OTHERS ARE 3/8" STUDS.
2. TWISTED PAIR WITH DRAIN IS REPRESENTED BY RED,
BLACK, & BLUE TWISTED WIRES. BLUE IS THE DRAIN,
RED IS CAN HI, & BLACK IS CAN LOW.
3. DISCHARGE TEMP. SENDER HAS TWO HOOK TERMINALS
INSTEAD OF TERMINAL RINGS.
4. PURPLE REPRESENTS SPLICES.
5. #(NUMBER) REPRESENTS WIRE NUMBER.
#25
#4
#5
#3
#6
#9
#21E
#10
#1E
#2E
#15
#16
#27
#44
#43
#24
#23
#14
#13
#7
#21
#1
#2
#21A
#2A
#1A
#31
#20#32
#34
#33
#30
#29
#29
#26C
#22
#10
#11
#28
#17B
#28
#30
#18
#17
#18A
#17A
#26
#26C
CAN
TERMINATOR
H
AB
CD
E
K
J
G
F
JD LINK DUST CAP
JD LINK
JD LINK
35-PIN MURPHY
JOHN DEERE
ECU CONNECTOR
CAN
TERMINATOR
RECEPTACLE
A
B
C
D
E
F
G
H
J
AB
BA
BA
PRESSURE
TRANSDUCER
FUEL
SENDER
C
A
USB
-
IGNITION
SWITCH
ALTERNATOR
EXCITATION
INTCON
USB
CONNECTOR
CONNECT
TERMINAL
HOOKS
DETAIL A
DETAIL B
DETAIL C
#31A
#26B
#9
#12
#15
#26A
1:1
CAN DIAGNOSTIC
CONNECTOR
DISCHARGE
TEMP. SENDER
STARTER
SOLENOID
#25
#6
#5
#4
#3
#8
#20
#19
#18
#17
#21C
#1C
#2C
#16
#12
#11
#21D
#2D
#1D
#19
#18A
#8
#26
#22
2
1
21
7
13
14
23
24
27
43
44
C
B
A
21
C
B
A
1
2
3
5
6
C
D
E
F
H
J
G
25
24
1
13
2
8
20
19
28
27
29
14
26
A
B
E
D
C
BA
A
B
1
2
3
5
AB
CD
E
F
5
4
3
2
1
F
E
D
C
B
A
4
B
JDS
FIRST USED ON:
3RD ANGLE
PROJECTION
1201 West US Highway 20, Michigan City IN 46360
1-800-438-6203
SHEET
SCALE:
TOLERANCES AS FOLLOWS:
REV
DESCRIPTION
THIS DRAWING AND ALL INFORMATION THEREIN IS THE PROPERTY OF SULLIVAN-PALATEK, INC. IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED.
WWW.SULLIVANPALATEK.COM
SULLIVAN-PALATEK
CHECKED BY:
DATE:
DATE:
DRAWN BY:
ANGLES: + OR - 1/2 DEG.
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE NOTED
X.XXX + OR - 0.005
X.XX + OR - 0.020
DECIMAL: X.X + OR - 0.050
MATERIAL:
IT IS LOANED SUBJECT TO RETURN UPON DEMAND, IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANYWAY DETRIMENTAL TO SULLIVAN-PALATEK'S INTEREST.
DRAWING NO:
SIZE
1 OF 1
D210UHJD4
MFP
08/24/15
08/24/15
01
WD-15115
D210UHJD4
DIAGRAM, WIRING
12
2.5 WIRING DIAGRAM, STARTER
DRIVE COUPLING HOUSING (REF.)
ALTERNATOR (REF.)
STARTER (REF.)
COOLER PACK SHROUD(REF.)
SOLENOID(REF.)
STARTER POWER WIRE # 1
STARTER GROUND WIRE # 2
SOLENOID GROUND WIRE # 3
ALTERNATOR POWER WIRE # 5
ALTERNATOR GROUND WIRE # 4
A
WIRE # 5
BLACK
WIRE # 1
RED
WIRE # 2
BLACK
WIRE # 3
GREEN
WIRE # 4
GREEN
B
C
DETAIL A
ALTERNATOR
WIRE # 4
WIRE # 5
DETAIL B
STARTER
WIRE#5WIRE#2
WIRE#1
WIRE#3
DETAIL C
SOLENOID
WIRE #1
WIRE #2
WIRE #3
NTS
A
B
C
D
E
F
F
E
D
C
B
A
5
4
3
2
1
1
2
3
4
C
JDS
FIRST USED ON:
3RD ANGLE
PROJECTION
1201 West US Highway 20, Michigan City IN 46360
1-800-438-6203
SHEET
SCALE:
TOLERANCES AS FOLLOWS:
REV
DESCRIPTION
THIS DRAWING AND ALL INFORMATION THEREIN IS THE PROPERTY OF SULLIVAN-PALATEK, INC. IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED.
WWW.SULLIVANPALATEK.COM
SULLIVAN-PALATEK
CHECKED BY:
DATE:
DATE:
DRAWN BY:
ANGLES: + OR - 1/2 DEG.
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE NOTED
X.XXX + OR - 0.005
X.XX + OR - 0.020
DECIMAL: X.X + OR - 0.050
MATERIAL:
IT IS LOANED SUBJECT TO RETURN UPON DEMAND, IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANYWAY DETRIMENTAL TO SULLIVAN-PALATEK'S INTEREST.
DRAWING NO:
SIZE
1 OF 1
D250UJD4
JPC
2/15/16
2/15/16
00
WD 15116
DIAGRAM, WIRING JD4045TCF03
STARTER AND GROUND
Table of contents
Other Sullivan-Palatek Air Compressor manuals
Sullivan-Palatek
Sullivan-Palatek D110PKU User manual
Sullivan-Palatek
Sullivan-Palatek D300PDKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek VFD Series User manual
Sullivan-Palatek
Sullivan-Palatek D110PKUW User manual
Sullivan-Palatek
Sullivan-Palatek 75UDG User manual
Sullivan-Palatek
Sullivan-Palatek D185PIZP Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek DC185P3JD User manual
Sullivan-Palatek
Sullivan-Palatek 125G User manual
Sullivan-Palatek
Sullivan-Palatek 15D User manual
Sullivan-Palatek
Sullivan-Palatek UD Series User manual
Sullivan-Palatek
Sullivan-Palatek D210PHKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D260PDKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D185UIZ Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek D185PKR Installation and operating instructions
Sullivan-Palatek
Sullivan-Palatek 125UD User manual
Popular Air Compressor manuals by other brands
EasyPro
EasyPro EPW2 instructions
TOOLCRAFT
TOOLCRAFT 2619529 Original instructions
Parkside
Parkside PDLS 5 B1 Operation and safety notes translation of the original instructions
HILL PUMPS
HILL PUMPS EC-3000 User instruction manual
Quincy
Quincy QGS 10 Instruction book
BAE Audio
BAE Audio 10DC instruction manual