Sulov REBEL User manual

INSTRUCTIONS FOR USE (GB)
Scooter REBEL
If the package is missing a part or is defective, contact your dealer.
Please note:
Maximum user weight: 100 kg –Class A

For users aged 5 years and over

Check and tighten all screws and bolts before each ride

Before each trip, make sure that all components are working properly.

Inflate the tires to the maximum pressure listed on the tire sidewall.

When riding, wear protective clothing. Helmet, knee and elbow pads and
sturdy shoes. This greatly reduces the risk of injury, but not completely.

If any item is damaged or not working properly, it should be replaced
or repaired before riding.

Avoid riding on uneven surfaces, avoid drain covers, drainage channels
and gutters.

Do not ride on the road or other surface covered with water, sand or
gravel, or otherwise contaminated. In rainy weather visibility is reduced,
avoid sharp turns and braking.

Avoid driving fast, especially on steep hills.

The brake parts heat up in use, therefore after each braking activity
always fully release the lever. For the same reasons do not touch the
braking mechanism immediately after stopping.
IMPORTANT
CAUTION: Building the scooter must be supervised by an adult.
Before riding the scooter must be completely assembled.
Before using the scooter, read this manual carefully.
Only use the Scooter as described in the instructions.
Failure to follow these instructions can result in injury.
We recommend you to check the usage restriction of the
scooter considering rules of road safety.
(17)
PRECAUTIONS
THIS SCOOTER IS NOT RECOMMENDED FOR USERS 5 YEARS
OR PERSONS OVER 100 KG IN WEIGHT.
Read and observe the following measures, to avoid injury to the user or
breakage of scooter.
PLEASE EDUCATE YOUR CHILD ABOUT PROPER USE OF SCOOTERS,
AND ALSO ABOUT THE FOLLOWING PRECAUTIONS.
WARNING: DO NOT use the scooter on the road.
A. Wear a helmet and knee, elbow and hand/wrist protectors.
B. Do not ride close to motor vehicle.
C. Try brakes in a safe place.
D. Do not ride on or near the stairs, sloping road, hills, roads and
swimming pools or other bodies of water.
E. The scooter is designed for only one person.
F. Do not ride in rainy weather, wet surface extends braking distance.
G. Never tow another vehicle or child on skates or skateboard.
H. Do not operate at night, in the dark.
I. Always wear shoes.
J. Avoid pedestrians, do not ride too close to them.
K. Avoid risky places where maneuverability of the scooter decreases.
Holes, potholes, ruts, rough terrain, channel gratings, gravel,
curb, leaves, puddle, all affect driving and may cause an accident.
L. Do not drive off-road or on rough surfaces.
M. Keep both hands on the handlebars.
N. Do not use anything that prevents hearing.
WARNING: Brake carefully to get a skid, or too abruptly stopped.
Shear significantly increases tire wear can lead to damage.
The product meets the requirements of DIN EN 14619.
Importer and distributor for EU:
Rulyt s.r.o., 5. kvetna 435, CZ-440 01 Dobromerice
(18)

ASSEMBLY INSTRUCTIONS
Unassembled scooter (photo illustration)
Figure 1a,b
Remove the scooter out of the box and make sure the package contains all the
parts and if not damaged. (Make sure the tires are inflated. Make sure they are
inflated to 35 psi. It is possible that during transport pressure lost.)
Build scooters consists of two main steps.
1 - Installing wheels.
2 - Installation of the handlebar.
FITTING THE WHEEL
INSTALLING WHEELS
Slide the rear wheel axle completely into the rear fork. On the axle mount
locking plates (Fig.1a), so that they protrude into the round holes in the frame.
Plate must be outside of the frame, between the frame and the nut. On the
axle affix the nuts (Fig. 1b).
Make sure the wheel is centered and tighten nut with spanner.
Note: See Figure 1 on the next page.
Note: The front and rear wheel is mounted in the same way.
Note: The rear wheel can already be installed from the factory.
Rear wheel:
Insert a fork,
Screw the nut (b) .
Tighten the nut wrench as
possible, without damaging
the thread (between about 25
Nm to 30 Nm).
Front wheel:
Insert a fork,
Screw the nut (b) .
Tighten the nut wrench as
possible, without
damaging the thread
(between about 25 Nm to
30 Nm).
When assembling
the bike, make
sure that the upper
edge of the brake
shoe is parallel to
the edge of the
rim.
When assembling the bike, make sure that the upper edge of the brake shoe
is parallel to the edge of the rim.
(19)
If it is necessary to replace the wheel, always use wheels / tires of the same
parameters as the original. To remove please reverse the installation steps
(see instructions).
(20)

ASSEMBLY HANDLEBAR
Insert the handlebar rod into the tube of the front fork (see Fig.2). Handlebars
area so that was perpendicular to the front wheel. Tighten the bolt with a
wrench. Make sure the handlebars secure.
Figure 2
Handlebars
Insert the handlebar rod into the tube
of front fork, at least to the minimum
Insert the
mark. Tighten the screw wrench NC
handlebar rod
(c), as it will go, but do not damage
into the tube of
the screw (18 to 20Nm).
front fork.
(c) The expansion screw
(21)
Setting the front and rear hand brakes
Note: The brakes on this scooter are not set from the factory.
Before you ride, you need these brakes fitted and adjusted.
Install the brake lever on the handlebars. Right lever controls the rear brake and left
lever controls the front brake.
Installation and brake adjustment:
1. First oval end of the brake cable into the round hole located in the brake lever (on
the handlebars) and route the brake cable jack in the bottom of the handle (see
Figure 1).
2. Press both arms of the V-brake towards the wheel rim and adjust the brake pads
(blocks) by appropriate wrench, so that during braking the brake rubbing its entire
surface on the side of the rim. If necessary, tighten or loosen the brake cable
using the anchor bolt or the adjusting screw on the brake lever so that the brake
pad and the rim was a gap of 1-2 mm. Make sure that the brake wire passes right
through the two parts of the brake and is tensioned (see Figure 2).
3. If the wheel does not turn freely and on one side there is a brake friction, tighten
the tensioning screw on the shoulder V-brakes to the wheel brakes, respectively.
loosen the tensioning screw on the opposite shoulder V-brakes.
4. Before driving, check the proper function of the brake. Repeatedly press together
and enable sticks brakes.
Warning: If after adjusting brakes brakes will still work, have the brakes adjusted by
a workshop for bicycles. Do not use the scooter when the brakes are not working or
are not adjusted.
Figure 1
Oval end of the
Slot for cable
management
brake cable
(22)

PREPARED SCOOTER
Color illustration
Thus, should a scooter after correct assembly.
Before using scooters, check the following:
1. Make sure that the handlebars are securely mounted.
2. Make sure that the tires are inflated to 35 psi.
3. Test the rear brake properly.
4. Check that both handlebar grips are firmly fixed.
5. Try foot stand.
6. Read the instructions for use on the next page.
So now you're ready to ride. But be sure to use a helmet and other
protective gear.
(23)
USE AND MAINTENANCE
USE SCOOTERS:
This non-motorized scooter with front and rear brake is designed for one driver. Not
suitable for persons weighing more than 100 kg. It is not designed for on-road, off road,
jumping, acrobatics, or for use with any motorized means of transport. Do not ride at
night, follow the traffic rules, pedestrians take precedence. Use caution when riding on
wet or slippery surfaces, especially when braking to avoid skids. Never leave your
scooter unlocked and unattended.
CORRECT RIDING AND BRAKING TECHNIQUE
Scooter should be used with caution, because the scooter riding requires certain skills.
Ability to drive and keep the body balance to avoid falls and accidents causing injury to
the user and others.
The user stands on the footboard while riding, bounce a foot from the ground and
controls the handlebars. When driving, keep both hands on the handlebars. Slow down
when turning or when you don´t go straight ahead and in danger of losing balance. Slow
down when you want to get down from the scooter. After a complete stop remove the first
one leg and then the other from the footboard. Slow down by pressing and holding the
brake lever on the handlebars.
Before start using the scooter, try all scooter controls to avoid falls and accidents.
MAINTENANCE SCOOTERS:
This scooter is well made and regular maintenance and judicious use will keep your
scooter in good condition for many years and the ride will be more safety.
Make a habit of regularly checking that everything is sufficiently tightened. Check that the
handlebars are secure, the axles of both wheels secured and brake is not loosened.
Check brakes before each ride. Check the brakes levers. Make sure that the brake pads
are not worn and cables are not frayed.
Note: Check tire pressure every week, the correct value is indicated on the tire sidewall.
Note: Riding on underinflated tires risks damaging the wheel or tire. The scooter may
become harder to handle.
Bearings and spokes are difficult to repair and replace. Therefore, their lubrication,
cleaning or replacement should be by a qualified service centre.
Self-locking nuts or other self-locking accessories, after frequent loosening and tightening
lose their effectiveness. In this case it is necessary to replace the self-locking part.
TOOLS REQUIRED FOR COMPILATION
Allen key
Multi wrench
Note: Tools not included. Picture of unassembled scooter in the manual is for
illustrative purposes only. Picture of scooters assembled in the instruction may differ
in cosmetics detail.
(24)