Summit 2009 REALTREE OUTFITTER'S Series User manual

2009 REALTREE® OUTFITTER’S SERIES
HAWK DELUXE
FOOTREST INSTRUCTIONS
FORM# 18006
PN 81509
BOX CONTENTS
In addition to the items lised on Page 2 of the 2009
Raptor Series Instructions, your treestand should
include the following:
PN DESCRIPTION QTY
40123 FOOTREST BAR 1
22029 FOOTREST HARDWARE PACKET 1
10903 CABELA’S EZ ARM BOWHANGER 1
CABELA’S MONSTER BUCKS XIV DVD 1
1 PARTS LIST
Please call 256-353-0634 or visit http://www.summitstands.com/contactus/
if you have any questions, if you need replacement parts, or if you have any missing parts.
22029 - FOOTREST HARDWARE KIT
PN DESCRIPTION QTY
10601 1 3/4” BOLT, 1/4x20 2
10612 LOCK NUT, 1/4x20 2
10640 LONG SHANK BUSHING 4
10641 SHORT SHANK BUSHING 2
10635 SELF TAPPING SCREW 4
10668 FOOTREST BUMPER 2
10122 FOOTREST MOUNTING BRACKET 2
NOTICE
These instructions are only for installing the included
footrest on the RS Hawk Deluxe (PN 81509).
ALWAYS refer to the 2009 Raptor Series Hang-
On Written Instructions for warnings and useage
instructions.

FOOTREST
(Installation is made easier by the use of a
powered screwdriver)
1. Insert the Footrest Bracket into the perimeter tube
as shown in figure 1. This bracket should be placed
between the first and second rung from the front of
the platform.
2. Secure the bracket with one self tapping screw as
shown in figure 2. Repeat for the other side.
3. Insert two of the long shank bushings into the
pre-punched holes in each end of the footrest tube as
shown in figure 3.
4. Insert the short shank bushing into the outside of
each footrest bracket from Step 1 (See figure 4).
5. Line up the footrest bar on the INSIDE of the two
footrest brackets and secure one side using the 1 1/2”
bolt and lock nut (see figure 5).
6. Insert the remaining 1 1/2” bolt through the other
side of the footrest bar and pull the bar to the side so
that you can tighten the lock nut. If squeaking occurs,
loosen the bolts by 1/2 turn.
7. Fold the bar down and note where it crosses the
stand frame - make a mark on the footrest at this
point. Fold the bar back up. Secure the two rubber
bumpers at the mark using the two remaining self
tapping screws as shown in figure 6. Your finished
footrest should look like figure 7.
1
FOOTREST BRACKET
(PN 10122)
Summit products are manufactured under one or more
of the following US Patents: 5,937,969; 5,971,104;
5,975,242; 5,979,603; 6,125,966; 6,182,792; 6,397,973;
D,417,011; D,420,147; D,575,411
Summit Bucksteps are Patent Pending
© 2009 Summit Treestands, LLC
715 Summit Dr. Decatur, AL 35601
2 TOOLS REQUIRED
Tools Use
7/16” Wrenches and / or Socket / Ratchet Footrest Attachment Bolts / Nuts
Powered Screwdriver Footrest self tapping screws
•
•
2
LONG
SHANK
BUSHING
(PN 10640)
3SHORT
SHANK
BUSHING
(PN 10641)
4
5
FOOTREST BUMPER
(PN 10668)
6 7