Sunbeam 32610081 User manual

Handheld Steamer
www.sunbeamhome.com
MODEL: 32610081
ITEM: 12905
Owner’s Guide
READ AND SAVE THESE INSTRUCTIONS

1
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed including the following:
1. READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
2. Use appliance only for its intended use.
3. To reduce the risk of electric shock, do not immerse the appliance in
water or other liquids.
4. Do not allow cord to touch hot surfaces. Let appliance cool completely
before putting away. Loop cord loosely around appliance when storing.
5. Always disconnect appliance from electrical outlet when filling with water
or emptying, and when not in use.
6. Do not operate appliance with a damaged cord, or if the appliance has
been dropped or damaged. To reduce the risk of electric shock, do not
disassemble or attempt to repair the appliance, contact customer service.
Incorrect reassembly or repair could cause a risk of fire, electric shock, or
injury to persons when the appliance is used.
7. Burns could occur from touching hot metal parts, hot water, or steam.
Use care when you turn a steam appliance upside down – there may be
hot water in the reservoir.
8. To reduce the risk of contact with hot water emitting from steam vents,
check appliance before each use by holding it away from body and
operating steam button.
9. To reduce the likelihood of circuit overload, do not operate another high
wattage appliance on the same circuit.
10. Never steam clothes while someone is wearing.
11. If an extension cord is absolutely necessary, a 15 ampere rated cord
should be used. Cords rated for less amperage may overheat. Care
should be taken to arrange the cord so that the cord cannot be pulled or
tripped over.
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Sunbeam®Handheld Travel Steamer with
powerful continuous steam technology. This Steamer will bring out the best
in garments, linens, drapes and more—quickly and efficiently!

2
12. When filling the water reservoir, watch for water that can drip onto the
floor and cause you to slip and fall.
13. Care should be taken to arrange the cord so that it cannot be pulled
or tripped over. Always make sure you can move freely without getting
tangled with the cord.
14. Appliance may cause personal injury or be damaged if dropped.
15. The use of attachments not recommended or sold by the appliance
manufacturer may cause injuries or void your warranty.
16. To avoid personal injury and damage to the appliance, only add water to
the water reservoir. NEVER add cleaning solutions, perfumes, oils or any
other chemical additives.
17. To reduce the risk of electrical shock, this appliance has a polarized plug
(one blade is wider than the other). This plug fits a polarized outlet only
one way; if the plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
18. When using the steamer for the first time, please check if voltage marked
on rating label matches the voltage in your home.
BEFORE FIRST USE
• Unpack your Steamer; remove and peel off any labels adhered to the
unit.
• Remove and save instruction manual.
• Wipe outside of the unit with a damp cloth or sponge to remove any
dust. Dry thoroughly.
• Keep unit on a flat, level surface.
• When using your Steamer for the first time, you may notice a small
amount of smoke and a slight odor. This is normal when heating the
appliance for the first time and there is no reason for concern.
IMPORTANT SAFEGUARDS CONT.

3
LEARNING ABOUT YOUR SUNBEAM®
VARIABLE TEMPERATURE HANDHELD STEAMER
1. Steam Plate
2. Steam Button
3. Handle
4. Voltage Selector Switch
5. Bristle Brush
6. Temperature Ready Light
7. Water Reservoir
8. Variable Steam Button
9. Power Cord

4
OPERATING INSTRUCTIONS
FILLING WATER RESERVOIR
Warning: To avoid personal injury and damage to the unit, only add water
to the water reservoir. NEVER add cleaning solutions, perfumes, oils or any
other chemical additives.
Note: Your Steamer is designed to be used with tap water. However, if you
have hard water, we recommend using distilled water for better results.
1. Place Steamer on a flat surface.
2. Gently Pull the Water Resevoir in lateral direction using your hand
(Figure 1).
3. Take the water reservoir to a sink. Pull the rubberized water-fill cover
to open and pour tap water from the faucet into the water-fill opening
until it reaches the Max water level in water reservoir (Figure 2). If water
spills outside of the reservoir, or within the center water reservoir cavity,
wipe it dry with a paper towel or cloth.
Warning: When filling the water reservoir, watch for water that can
drip onto the floor and cause you to slip and fall.
(Figure 1)
(Figure 2)

5
Tip: It is not necessary to have a full reservoir of water for the Steamer
to generate steam. For best results, just make sure the water reservoir is
at least half full.
4. Close the water-fill cover and refit the water reservoir into the stand.
Pull on the reservoir to ensure it is fully locked in position.
Note: If you need to add water while steaming, unplug the steamer,
wait until it cools and follow the above steps. If a cloud vibrating noise
is heard, then the water level is low and needs to be refilled.
USING YOUR STEAMER VERTICALLY
You can use your Steamer in the vertical position to press with steam
hanging garments and drapes.
1. Filled the water reservoir with water. Ensure that there is sufficient water
in the water reservoir.
2. Hang your garment to be steamed on a clean hanger.
3. Turn Voltage Selector Switch button to correct voltage based on the
country you are located in, and insert plug into the outlet with specified
voltage. Power indicator light will turn blue.
Warning: Incorrect voltage protection feature: if the voltage selected is
not the same as the outlet voltage, the steamer will not heat. The indicator
light with flicker red & blue alternately. To reset the steamer, unplug the
power cord from the outlet & select the correct voltage then insert the plug
into the outlet.
4. Plug the steamer into a standard electrical outlet and then turn on the
power, the indicator light will turn blue and flashes, then the device
enters the preheating stage. The product is not yet usable at this time.
When the indicator light flashes and stops, it indicates that the device
has completed preheating (preheating time is about 20 seconds). Press
the steam button twice for a burst of steam. Hold the steam button for
3 seconds for continuous steam for 3 minutes.
Warning: Care should be taken to arrange the cord so that it cannot
be pulled or tripped over. Always make sure you can move freely
without getting tangled with the cord.
Caution: Burns could occur from touching hot parts, hot water, or
steam. Use care when you turn a steam appliance upside down – there
may be hot water in the reservoir.
5. With your free hand, pull the fabric tight and press the steam button as
you move the Steamer over the fabric. Touch the fabric lightly with the
non-stick panel, moving it in a downward motion, beginning at the top
of the garment and moving downward. Repeat until fabric is wrinkle-free.

6
Warning: Steam is hot. Always point steamer exit away from yourself,
other persons, pets, plants and walls. Never steam clothes while they
are being worn.
6. For turbo mode (higher volume of steam), press the Variable Steam
button. The indicator light will change to red when in turbo mode.
7. When finished, press the Steam button.
8. Place Steamer on a flat surface and unplug from electrical outlet.
9. Wait until Steamer has cooled and empty water reservoir.
Note: Always unplug the Steamer when not in use.
AUTO-OFF FEATURE
If there is no operation for 8 minutes the appliance will turn to auto-off
mode and turn off the power. Switching any button in the following 15
minutes will turn the steamer back to the preheating mode. If there is no
operation following the 15 minutes, the steamer will cut off all power and
the power cord will need to be reinserted to turn on the steamer.
ASSEMBLING THE BRISTLE BRUSH ATTACHMENT
1. Place the hook on the bristle brush onto the groove of the upper
cover of the product. Press the tail of the bristle brush tightly towards
the body. When the sound of the buckle is heard, the bristle brush is
installed in place. (When assembling brush, please make sure the steam
plate is cold).
2. The bristle brush can improve steam penetration and quickly achieve
better steaming effects on heavy clothing such as jackets. Use the brush
with steam by pressing the steam switch and slowly moving the bristle
along the clothing.
Warning: before installing or disassembling the bristle brush, be sure
to unplug the power plug of the steamer, the steam plate may still be
hot.

7
STEAMING TIPS
• Improper use of the Steamer can cause property damage due to the
steam. Always read the instructions in this manual before using your
Steamer.
• Do not operate the Steamer with an empty water reservoir. To add water
during operation, turn steamer off, wait for it to cool down then remove
water reservoir and refill.
• Always read the fabric care labels to help determine fabric type to be
steamed. If unsure of fabric’s fiber, test a small hidden area, such as an
inside seam or hem, before steaming.
• For more difficult wrinkles, try steaming from the underside of the fabric.
• When steaming, touching fabric lightly with the steam nozzle can help in
wrinkle removal. It is important to make contact with the garment and/or
fabric.
• Heavier fabrics require more steam.
• Only use water in the unit. Do not add cleaning solutions, scented
perfumes, oils or any other chemicals to the water that can cause
damage to the appliance.
• Do not use steam directly against wall or doors.
• When hanging garment on a door while steaming, be careful not to
damage the door with steam.
• After use, empty water reservoir by turning it upside down to ensure all
water empties out and avoid leaks.
• When steaming, move the steamer continuously over the item being
pressed. Do not keep steamer over an area for any period of time to
avoid damage to the fabric.

8
CARE AND CLEANING
CLEANING
1. Make sure unit is off, unplugged and allow it to cool completely before
cleaning.
2. If there is water in the water reservoir, remove the reservoir and turn it
upside down to ensure all the water empties out.
3. Wipe exterior surfaces with a soft, damp cloth. Dry thoroughly.
Warning: Never immerse steamer, cord or plug in water or any other
liquid.
• Do not use abrasive cleaners or scouring pads that can scratch
the surface.
• Do not place in the dishwasher.
CLEANING WITH VINEGAR AND WATER
It is recommended to clean your Steamer every two months to reduce
mineral buildup that can affect the performance of your unit.
Warning: Do not use steel wool, abrasive cleaners, or corrosive liquids
(such as alcohol, gasoline, or acetone) to clean the product.
1. Turn off the unit and let it cool completely.
2. Remove water reservoir and make sure it is empty.
3. Fill water reservoir with a solution of 50% white vinegar and 50% water
up to the max level.
4. Plug unit into electrical outlet and press trigger to run a full steaming
cycle.
5. Once steaming is finished, fill with clean water and repeat process until
the vinegar odor is eliminated.
STORAGE
Under Storage, store the unit in upright position, in a clean dry place with a
flat, sturdy surface. Make sure the water reservoir is empty. If not, remove it
and turn it upside down to ensure all the water empties out and avoid leaks.
Store the product and all accessories in a cool, well-ventilated, and dry area.

9
Problem Possible Cause Solution
The steamer is not heating up. The steamer may not be plugged
in correctly, or the power may
not be turned on.
Ensure that the steamer is
properly plugged in and that the
power is turned on. Check if the
plug is inserted correctly and if
the outlet is working normally.
The steamer does not produce
any steam.
The steamer does not produce
any steam, the steamer has not
heated up sufficiently.
Steam button is not fully pressed
down
The water level in the water
reservoir is too low.
Electrical outlet is not working.
The water reservoir is not
properly placed.
Let the steamer preheat for 30
seconds before using. Wait until
the indicator light turns solid blue
and then press the power button.
Fully press down the steam
button for few seconds.
Unplug the steamer, let it cool
completely and refill the water
reservoir.
Plug into another electrical
outlet.
Insert the water reservoir
properly.
The steamer makes a rattling
noise and vibrates.
The water pump inside the unit
detects the water level is low.
Unplug the unit, let it cool
completely and refill water
reservoir.
The steamer leaves water drops
on the garment.
The accessory attachment being
used may have condensation.
Let the appliance cool
completely, remove attachment
and wipe dry.
The steamer is making a buzzing
noise while steaming / handle
shakes.
The water pump sends steam
to the steam panel to produce
steam.
This noise is normal.
If the indicator light is flashing
back & forth between red & blue
Actual outlet voltage & the
voltage selected are not the same
The voltage switch must be set
to the same voltage as the outlet
voltage
TROUBLESHOOTING