Sunbeam Flossy FF5300 User manual

Please read these instructions carefully
and retain for future reference.
Flossy
Fairy Floss Maker
Instruction Booklet
FF5300

Contents
Sunbeam’s Safety Precautions 1
Features of Flossy your Fairy Floss Maker 2
Assembly Instructions 4
Using your Fairy Floss Maker 5
Fairy Floss Measurements 7
How to Make Paper Cones 7
Care & Cleaning 8
Bowl & Body
Extractor Head and Assembly

1
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Sunbeam’s Safety Precautions
Sunbeam are very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• Close supervision is necessary when your
appliance is being used near children or
infirm persons.
• Never leave an appliance unattended while
in use.
• Young children should be supervised to ensure
that they do not play with the appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• For safety reasons and to avoid maintenance
by unskilled persons, some appliances are
‘sealed’ using tamperproof screws. Such
appliances should always be returned to the
nearest Sunbeam Appointed Service Centre
for adjustment or repair if required.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
dropped or damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
SAFETY PRECAUTIONS FOR FLOSSY THE
FAIRY FLOSS MAKER.
• This appliance is not a toy.
• Operate the fairy floss maker on a flat
surface.
• Do not leave your fairy floss maker
unattended.
• Do not place any part of this appliance in a
dishwasher.

2
Features of ‘Flossy’ your
Fairy Floss Maker
Bowl
Lightweight easy to clean fairy floss bowl.
Safety Lid
Designed to keep little fingers away
from the heating element.
Extractor Assembly Head
Pour in 1 tablespoon of sugar
to produce fun fairy floss.
OFF/FLOSS Switch
Indicates when the unit is switched off.
Non-slip rubber feet
Non-slip rubber feet provides extra stability.

unlock lock
3
Fairy Floss Cones
Fairy
Floss
Scoop

1.Before using your Fairy Floss Maker for the
first time ensure that all packing material
is removed.
2.Wash the extractor head assembly and
bowl using warm and soapy water, dry
thoroughly.
3.Align the interlocking tabs on the fairy
floss maker with the tabs on the bowl. Turn
the bowl anti-clockwise onto the base and
lock into position. Please refer to graphics
on the unit and side of bowl.
4.Assemble the extractor head assembly to
the fairy floss maker ensuring that the
head is fitted correctly and securely.
NOTE: Should the Extractor Head Assembly
not be attached properly failure in
producing fairy floss may occur and the
unit may cause excessive vibration.
4
Assembly Instructions
unlock lock
unlock lock
unlock lock

5
Using your Fairy Floss Maker
1.Set the off/floss switch to the FLOSS
position and allow the fairy floss maker to
warm up for a minimum of 5 minutes.
2.Once warm set the off/floss switch to the
OFF position, when the extractor head
assembly has stopped spinning, put one
scoop (as provided) or 3 teaspoons of
granulated white sugar into the centre of
the extractor head and spread evenly. Sugar
should only be put in after the extractor
head assembly completely stops spinning.
NOTE: Use only pure granulated white sugar.
The use of other sugars, including
substitutes, will fail to produce fairy floss. Do
not use caster sugar. Do not use more than
the recommend quantity as excessive sugar
can cause noise and vibration of the unit.
3.Set the off/floss switch to the FLOSS
position. The extractor head assembly
starts to rotate and is heated by the
heating element.
4.After 1-2 minutes, fairy floss will start to
produce fine cobwebs. This forms around
the rim of the bowl.
5.With the paper cones supplied, position
vertically and wind the cone along the
inside of the bowl clockwise, several times.
Once the fairy floss has gripped onto the
cone turn the cone into a horizontal
position and rotate it above the extractor
head assembly to fully wind the fairy floss.

6.After fairy floss has been produced, switch
unit OFF then repeat steps 2-5 for more
fairy floss.
NOTE: If making a number of fairy floss
cones, dry sugar may build up around the
inside of the bowl near the lip. Remove the
dry sugar by scraping clean to prevent floss
from catching. Do not use a wet cloth
during this process. The edge of the sugar
scoop can be used.
6
Using your Fairy Floss Maker continued

7
AMOUNT OF SUGAR MAKES
1 scoop 1 cone
*If sugar scoop is misplaced use 3 teaspoons of sugar
To measure the required amount of sugar use
the scoop provided. If using a metric
measuring scoop ensure that 3 teaspoons is
only used.
NOTE: Do not put in more than the required
amount of sugar as this will cause the unit to
vibrate and excessive noise will occur.
Fairy Floss Measurements
How to Make Paper Cones
1.Take a sheet of A4 paper and place it on a
flat surface.
2.Take the left bottom corner and coil the
paper towards the right bottom corner,
rolling tightly as you go.
3.When you reach the right bottom corner,
grasp the full cone and place a piece of
sticky tape to seal it.

8
To clean the bowl & the body
1.Set the off/floss switch to the OFF position
and remove the plug from the power point.
2.Turn the bowl clockwise to remove from the
main part of the body.
NOTE: Never use abrasive cleaners or
solvents, as they may scratch the surface.
3.Wash the bowl with a soft cloth or sponge
using cold or warm soapy water.
4.Dry the bowl thoroughly before using again.
NOTE: Never immerse body in water or any
other liquid.
To clean the extractor head assembly
1.Set the off/floss switch to the OFF position
and remove the plug from the power point.
2.Allow the extractor head to cool down for
approximately 20 minutes before removing
from body.
3.Soak the extractor head assembly in hot
water before washing to loosen sugar
deposits and to make cleaning easier.
Wash the extractor head assembly with a
soft cloth or sponge in warm soapy water
and dry thoroughly. Do not use abrasive
cleaners or solvents.
Care & Cleaning