Sunbeam 2377 User manual

User
Manual
STAND MIXER
Model 2377
BATIDORA DE PIE
MODELO 2377
Manual
delUsuario
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 2

Safety safety
SPECIAL INSTRUCTIONS
iii
This Unit Is for Household Use Only
When your MIXMASTER® Mixer is first used, you
may experience an odor and possibly a slight wisp of
smoke from your mixer’s motor. This is caused by the
heat curing of the insulation which protects the motor
and is normal. After the first few uses, this effect will
disappear.
FOR PRODUCTS PURCHASED IN THE U.S. AND
CANADA ONLY
To reduce the risk of electrical shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug fits a polarized outlet only one way; if the
plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
SAVE THESE
INSTRUCTIONS
safety
When using electrical appliances, basic safety precautions
should always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING THE
MIXER.
• To protect against risk of electrical shock, do not put
Mixer in water or other liquid. This may cause personal
injury or damage to the product.
• Close supervision is necessary when Mixer is used by or
near children or incapacitated persons.
• Unplug from outlet while not in use, before putting on or
taking off parts and before cleaning.
• Avoid contacting moving parts. Keep hands, hair,
clothing, as well as spatulas and other utensils away from
beaters during operation to reduce the risk of injury to
persons and/or damage to the Mixer.
• Do not operate Mixer with a damaged cord or plug or
after the appliance malfunctions, or is dropped or
damaged in any manner. Return appliance to the nearest
Authorized Sunbeam Appliance Service Center for
examination, repair or electrical or mechanical
adjustment.
• The use of attachments not recommended or sold by
Sunbeam may cause fire, electrical shock or injury.
• Do not use outdoors or for commercial purposes.
• Do not let cord hang over edge of table or countertop or
touch hot surfaces, including the stove.
• Remove beaters from Mixer before washing.
• Do not place Mixer or bowls on or near a hot gas or
electric burner, or in a heated oven.
• Do not use Mixer for other than intended use.
• Do not leave Mixer unattended while it is operating.
IMPORTANT SAFEGUARDS
ii
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 4

Safety safety
SPECIAL INSTRUCTIONS
iii
This Unit Is for Household Use Only
When your MIXMASTER® Mixer is first used, you
may experience an odor and possibly a slight wisp of
smoke from your mixer’s motor. This is caused by the
heat curing of the insulation which protects the motor
and is normal. After the first few uses, this effect will
disappear.
FOR PRODUCTS PURCHASED IN THE U.S. AND
CANADA ONLY
To reduce the risk of electrical shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug fits a polarized outlet only one way; if the
plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
SAVE THESE
INSTRUCTIONS
safety
When using electrical appliances, basic safety precautions
should always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING THE
MIXER.
• To protect against risk of electrical shock, do not put
Mixer in water or other liquid. This may cause personal
injury or damage to the product.
• Close supervision is necessary when Mixer is used by or
near children or incapacitated persons.
• Unplug from outlet while not in use, before putting on or
taking off parts and before cleaning.
• Avoid contacting moving parts. Keep hands, hair,
clothing, as well as spatulas and other utensils away from
beaters during operation to reduce the risk of injury to
persons and/or damage to the Mixer.
• Do not operate Mixer with a damaged cord or plug or
after the appliance malfunctions, or is dropped or
damaged in any manner. Return appliance to the nearest
Authorized Sunbeam Appliance Service Center for
examination, repair or electrical or mechanical
adjustment.
• The use of attachments not recommended or sold by
Sunbeam may cause fire, electrical shock or injury.
• Do not use outdoors or for commercial purposes.
• Do not let cord hang over edge of table or countertop or
touch hot surfaces, including the stove.
• Remove beaters from Mixer before washing.
• Do not place Mixer or bowls on or near a hot gas or
electric burner, or in a heated oven.
• Do not use Mixer for other than intended use.
• Do not leave Mixer unattended while it is operating.
IMPORTANT SAFEGUARDS
ii
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 4

welcome
Congratulations! You are the owner of a SUNBEAM®
Stand Mixer.
Before you use this product for the first time, please take
a few moments to read these instructions and keep it for
reference. Pay particular attention to the Safety
Instructions provided. Please review the product service
and warranty statements. For your future reference,
please note:
Date product received:
Service number:
(Located on the bottom of the stand mixer)
FEATURES
Thank you for choosing the SUNBEAM®Mixer. For
generations we have been helping cooks prepare moist
cakes, light and fluffy meringue and chewy cookies.
You can even make bread dough with your SUNBEAM®
Mixmaster®Mixer.
The SUNBEAM®Mixmaster®Mixer offers you a choice
of 12 different mixing speeds.
The Bowl-Fit Beaters and Bowls have been designed
to mix ingredients thoroughly and evenly.
No problem ejecting the beaters either – just push the
Ejector Button located on the side of the handle.
You’ll love being able to make so many things with
your Mixer!
Welcome
1
contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Learning About Your Stand Mixer . . . . . . . . . . . . . . . . .2
Assembling the Stand Mixer . . . . . . . . . . . . . . . . . . . . .3
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .6
Mixing Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Breads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Using Dough Hooks . . . . . . . . . . . . . . . . . . . . . . .11
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
One-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . .14
How to Obtain Warranty Service . . . . . . . . . . . .14
Table of Contents
iv
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 6

welcome
Congratulations! You are the owner of a SUNBEAM®
Stand Mixer.
Before you use this product for the first time, please take
a few moments to read these instructions and keep it for
reference. Pay particular attention to the Safety
Instructions provided. Please review the product service
and warranty statements. For your future reference,
please note:
Date product received:
Service number:
(Located on the bottom of the stand mixer)
FEATURES
Thank you for choosing the SUNBEAM®Mixer. For
generations we have been helping cooks prepare moist
cakes, light and fluffy meringue and chewy cookies.
You can even make bread dough with your SUNBEAM®
Mixmaster®Mixer.
The SUNBEAM®Mixmaster®Mixer offers you a choice
of 12 different mixing speeds.
The Bowl-Fit Beaters and Bowls have been designed
to mix ingredients thoroughly and evenly.
No problem ejecting the beaters either – just push the
Ejector Button located on the side of the handle.
You’ll love being able to make so many things with
your Mixer!
Welcome
1
contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Learning About Your Stand Mixer . . . . . . . . . . . . . . . . .2
Assembling the Stand Mixer . . . . . . . . . . . . . . . . . . . . .3
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .6
Mixing Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Breads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Using Dough Hooks . . . . . . . . . . . . . . . . . . . . . . .11
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
One-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . .14
How to Obtain Warranty Service . . . . . . . . . . . .14
Table of Contents
iv
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 6

stand mixer
Before assembling the mixer, be sure the speed
control dial is in the OFF position and the electric
cord is unplugged.
Attaching the Turntable
Place the revolving turntable into the base of the
stand by pressing the turntable into the center hole
of the adjustment slot until it snaps into place.
Adjusting the Turntable
The turntable must be adjusted depending upon
which bowl size is being used (see “Adding the
Mixing Bowl”). To adjust, press down on the
turntable locator switch and slide switch to the
proper icon.
Attaching and Removing Mixer Head
To attach the mixing head, press in on the mixer-
release trigger, located at the rear of the stand.
Place the mixer head on the stand so that the metal
pivot on the bottom of the mixer head goes into the
latched opening on the top of the stand.
As you release pressure from the mixer-release
trigger, the top of the latch should clamp around the
metal pivot. Once the mixing head is lowered into
position, it will lock into place.
To raise the mixing head, press the head lock button
downward while pulling up on the handle of the
mixing head. Once unlocked, the mixing head can be
removed by pressing the mixer release trigger. Be sure
the mixer head is securely in position before using.
NOTE: This mixer is NOT intended for use away
from the stand.
Assembling the Stand Mixer
3
your mixer
Learning About Your Stand Mixer
2
A. Beater Ejector
B. BURST OF
POWER®
Feature
C. Speed Control
Dial
D. Mixer-Release
Trigger
E. Headlock
F. Stand
G. Dough Hooks
H. Turntable
Locator Switch
I. Turntable
J. Bowl-Fit Beaters
Ka. Large Mixing
Bowl
Kb. Small Mixing
Bowl
AB
C
D
E
F
G
H
I
J
Ka
Kb
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 8

stand mixer
Before assembling the mixer, be sure the speed
control dial is in the OFF position and the electric
cord is unplugged.
Attaching the Turntable
Place the revolving turntable into the base of the
stand by pressing the turntable into the center hole
of the adjustment slot until it snaps into place.
Adjusting the Turntable
The turntable must be adjusted depending upon
which bowl size is being used (see “Adding the
Mixing Bowl”). To adjust, press down on the
turntable locator switch and slide switch to the
proper icon.
Attaching and Removing Mixer Head
To attach the mixing head, press in on the mixer-
release trigger, located at the rear of the stand.
Place the mixer head on the stand so that the metal
pivot on the bottom of the mixer head goes into the
latched opening on the top of the stand.
As you release pressure from the mixer-release
trigger, the top of the latch should clamp around the
metal pivot. Once the mixing head is lowered into
position, it will lock into place.
To raise the mixing head, press the head lock button
downward while pulling up on the handle of the
mixing head. Once unlocked, the mixing head can be
removed by pressing the mixer release trigger. Be sure
the mixer head is securely in position before using.
NOTE: This mixer is NOT intended for use away
from the stand.
Assembling the Stand Mixer
3
your mixer
Learning About Your Stand Mixer
2
A. Beater Ejector
B. BURST OF
POWER®
Feature
C. Speed Control
Dial
D. Mixer-Release
Trigger
E. Headlock
F. Stand
G. Dough Hooks
H. Turntable
Locator Switch
I. Turntable
J. Bowl-Fit Beaters
Ka. Large Mixing
Bowl
Kb. Small Mixing
Bowl
AB
C
D
E
F
G
H
I
J
Ka
Kb
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 8

assembling
Assembling
ATTACHING THE DOUGH HOOKS
Set the speed dial in the OFF position and unplug
the electric cord from the electrical outlet. Lift mixer
head up and back to tilt it out of the way of the
bowl, while holding it in an upright position.
NOTE: The dough hooks must go into the correct
sockets. The mixer will operate with the dough
hooks in the wrong position. However, you will not
get proper kneading action and you could risk
ruining a recipe or damaging your mixer. Read the
following instructions carefully.
The dough hook with the small washer and foot
goes into the socket on the side of the mixer nearest
the side of the bowl. The other dough hook with the
large washer goes into the socket nearest the center
of the bowl. See the dough hook symbols located on
the bottom of the mixer head.
5
assembling
Adding the Mixing Bowl
Move the turntable locator switch to the proper
setting – the large bowl icon if you are using the
large bowl; the small bowl icon if you are using a
small bowl. Place the desired mixing bowl onto the
turntable.
Mixing bowls should NEVER be used in a
conventional oven, microwave oven, on top of the
range or on any other heated surface. If mixing
bowls are scratched or chipped, do not use mixer.
Mixer bowl should not be used to blend in hot
liquids.
Attaching the Beaters
Be sure the speed control dial is in the OFF position
and unplug electric cord from the electrical outlet.
Lift mixer head up and back to pull it out of the
way of the bowl.
NOTE: It is important that the beaters go into the
correct sockets. Otherwise the mixer will not give
you the proper mixing action. Do not risk ruining a
recipe or damaging your mixer. Read the following
instructions carefully.
One of the beaters is shaped like a cone and has a
nylon button on the bottom. It goes into the socket
on the side of the mixer nearest the side of the
bowl. The other beater is square-shaped and goes
into the socket nearest the center of the bowl. See
beater symbols located on the bottom of the mixer
head.
Insert the beaters, one at a time, using a
combination pressing and twisting motion, until the
beaters snap into position.
If a beater should not properly snap into place, pull
it out of the socket and rotate it one quarter turn.
Reinsert the beater into the socket until it snaps
into position.
4
Assembling
CONE SHAPED
BEATER SQUARE BEATER
NYLON
BUTTON
SIDE OF BOWL
CONE
BEATER SQUARE BEATER
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 10

assembling
Assembling
ATTACHING THE DOUGH HOOKS
Set the speed dial in the OFF position and unplug
the electric cord from the electrical outlet. Lift mixer
head up and back to tilt it out of the way of the
bowl, while holding it in an upright position.
NOTE: The dough hooks must go into the correct
sockets. The mixer will operate with the dough
hooks in the wrong position. However, you will not
get proper kneading action and you could risk
ruining a recipe or damaging your mixer. Read the
following instructions carefully.
The dough hook with the small washer and foot
goes into the socket on the side of the mixer nearest
the side of the bowl. The other dough hook with the
large washer goes into the socket nearest the center
of the bowl. See the dough hook symbols located on
the bottom of the mixer head.
5
assembling
Adding the Mixing Bowl
Move the turntable locator switch to the proper
setting – the large bowl icon if you are using the
large bowl; the small bowl icon if you are using a
small bowl. Place the desired mixing bowl onto the
turntable.
Mixing bowls should NEVER be used in a
conventional oven, microwave oven, on top of the
range or on any other heated surface. If mixing
bowls are scratched or chipped, do not use mixer.
Mixer bowl should not be used to blend in hot
liquids.
Attaching the Beaters
Be sure the speed control dial is in the OFF position
and unplug electric cord from the electrical outlet.
Lift mixer head up and back to pull it out of the
way of the bowl.
NOTE: It is important that the beaters go into the
correct sockets. Otherwise the mixer will not give
you the proper mixing action. Do not risk ruining a
recipe or damaging your mixer. Read the following
instructions carefully.
One of the beaters is shaped like a cone and has a
nylon button on the bottom. It goes into the socket
on the side of the mixer nearest the side of the
bowl. The other beater is square-shaped and goes
into the socket nearest the center of the bowl. See
beater symbols located on the bottom of the mixer
head.
Insert the beaters, one at a time, using a
combination pressing and twisting motion, until the
beaters snap into position.
If a beater should not properly snap into place, pull
it out of the socket and rotate it one quarter turn.
Reinsert the beater into the socket until it snaps
into position.
4
Assembling
CONE SHAPED
BEATER SQUARE BEATER
NYLON
BUTTON
SIDE OF BOWL
CONE
BEATER SQUARE BEATER
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 10

guide
Mixing Guide
SPEED MIXING
SETTING GUIDE EXAMPLE
1 Fold-Kneaded Use when mixing dry ingredients or when
folding two portions of a recipe together,
such as a beaten egg white into a batter
or when directions call for LOW speed.
Use for kneading bread.
2 Stir Use when stirring liquid ingredients or
when gentle action is needed to moisten
dry ingredients.
3 Blend Use when quick breads require a brisk
action, just enough to blend ingredients
but not enough to develop a smooth
batter.
4 Mix Use when mixing dry ingredients and
liquid ingredients together alternately in
a recipe.
5 Combine Use when recipe calls for combining
ingredients together.
6 Cake Mixes Use when preparing packaged cake
mixes or when directions call for
MEDIUM speed.
7 Cream Use when creaming sugar and butter
together.
8 Whip Use to whip potatoes or to develop a
smooth batter.
9 Whip/Cream Use to whip whipping cream or to
develop a light, fluffy texture.
10 Desserts Use to beat air into whipped desserts.
11 Frostings Use when preparing light, fluffy frostings
and candies.
12 Egg Whites Use when aerating eggs and egg whites.
Use when directions call for HIGH speed.
NOTE: Due to variations in ingredient temperatures and quantities, the Mixing
Guide speeds are only suggested. If necessary, adjust speeds as needed to
achieve desired results.
7
operating
ABOUT THE SPEED CONTROL DIAL
The speed control dial is used for turning the mixer
ON and OFF and for selecting its 12 mixing speeds.
Rotate the speed control dial in a clockwise
direction to increase mixing speed; and in a counter-
clockwise direction to decrease mixing speed.
As you rotate the speed control dial, notice that a
numbered speed is aligned with the indicator on top
of the mixer head. This numbered speed indicates
the speed at which the mixer is operating.
Rotate the speed control dial until the indicator is
opposite the numbered speed you wish to use.
BURST OF POWER®FEATURE
Press down on button or top handle to
automatically increase the beater speed by 150
RPM for an immediate boost of power.
HEAD LOCK
The head lock feature locks the mixing head in the
down position for added control while mixing and
locks it in the up position for added convenience
while cleaning.
To unlock, press down the button on the side of the
stand.
To lock, lower mixing head until it automatically
locks in place.
Operating Instructions
6
SPEED
INDICATOR
MIXING GUIDE
SPEED
CONTROL
DIAL
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 12

guide
Mixing Guide
SPEED MIXING
SETTING GUIDE EXAMPLE
1 Fold-Kneaded Use when mixing dry ingredients or when
folding two portions of a recipe together,
such as a beaten egg white into a batter
or when directions call for LOW speed.
Use for kneading bread.
2 Stir Use when stirring liquid ingredients or
when gentle action is needed to moisten
dry ingredients.
3 Blend Use when quick breads require a brisk
action, just enough to blend ingredients
but not enough to develop a smooth
batter.
4 Mix Use when mixing dry ingredients and
liquid ingredients together alternately in
a recipe.
5 Combine Use when recipe calls for combining
ingredients together.
6 Cake Mixes Use when preparing packaged cake
mixes or when directions call for
MEDIUM speed.
7 Cream Use when creaming sugar and butter
together.
8 Whip Use to whip potatoes or to develop a
smooth batter.
9 Whip/Cream Use to whip whipping cream or to
develop a light, fluffy texture.
10 Desserts Use to beat air into whipped desserts.
11 Frostings Use when preparing light, fluffy frostings
and candies.
12 Egg Whites Use when aerating eggs and egg whites.
Use when directions call for HIGH speed.
NOTE: Due to variations in ingredient temperatures and quantities, the Mixing
Guide speeds are only suggested. If necessary, adjust speeds as needed to
achieve desired results.
7
operating
ABOUT THE SPEED CONTROL DIAL
The speed control dial is used for turning the mixer
ON and OFF and for selecting its 12 mixing speeds.
Rotate the speed control dial in a clockwise
direction to increase mixing speed; and in a counter-
clockwise direction to decrease mixing speed.
As you rotate the speed control dial, notice that a
numbered speed is aligned with the indicator on top
of the mixer head. This numbered speed indicates
the speed at which the mixer is operating.
Rotate the speed control dial until the indicator is
opposite the numbered speed you wish to use.
BURST OF POWER®FEATURE
Press down on button or top handle to
automatically increase the beater speed by 150
RPM for an immediate boost of power.
HEAD LOCK
The head lock feature locks the mixing head in the
down position for added control while mixing and
locks it in the up position for added convenience
while cleaning.
To unlock, press down the button on the side of the
stand.
To lock, lower mixing head until it automatically
locks in place.
Operating Instructions
6
SPEED
INDICATOR
MIXING GUIDE
SPEED
CONTROL
DIAL
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 12

MIXING AND BAKING SUGGESTIONS
• Ingredients should be added to the mixing bowl as they
are specified in the recipe. When combining dry and
wet ingredients, you may wish to moisten ingredients
on Speed 1 or 2, then turn to the desired mixing speed.
• Use the mixing speed that is recommended in the
recipe. Use the handy mixing guide on the speed
control dial of the mixer to help you find the correct
speed to use.
• If times are specified in the recipe, use them! BE
CAREFUL NOT TO OVERMIX. Overmixing can
cause the mixture to become very tough.
• Should an object, such as a spatula, fall into the bowl
while the mixer is operating, turn the mixer OFF
immediately. Then, remove the object.
• Remove beaters and place in sink for easy clean-up.
• When preparing your favorite dish, DO NOT exceed
3 1/2cups of flour in any recipe.
hints
Helpful Hints
To Order additional ACCESSORIES,
CALL 1-800-458-8407.
DESCRIPTION MODEL NO.
Dough Hooks 4964
Beater 4950
Large Glass Bowl 4938
Small Glass Bowl 4939
Large Stainless Steel Bowl 4951
Small Stainless Steel Bowl 4952
9
EJECTING THE BEATERS OR DOUGH HOOKS
After you’ve finished mixing, turn the speed control
dial to OFF and unplug the electric cord from the
electrical outlet. Push the ejector button located near
the handle to remove beaters or dough hooks.
Scrape excess batter off the beaters using a rubber or
plastic spatula. Do not strike beaters on the rim of
the bowl.
CLEANING YOUR MIXER
To clean the mixer, wipe the mixer head, stand and
turntable with a damp cloth, then dry. DO NOT
IMMERSE THE MIXER HEAD OR STAND IN
WATER. Avoid the use of abrasive cleaners, as they
may mar the finish of the mixer.
Wash the beaters and bowls in hot, soapy water after
each use. Rinse thoroughly and dry. Beaters and
bowls may also be washed in an automatic
dishwasher.
STORING YOUR MIXER
Store the mixer in a dry location, such as on a
countertop or table top, or in a closet or cupboard.
Insert the beaters into the proper sockets. Place the
dough hooks in the mixing bowl.
Store the bowl(s) on the turntable. The beaters will
help hold the bowl in position. Wind the electric cord
into a coil, secure it with a twist fastener.
MAINTENANCE
The motor of your stand mixer has been carefully
lubricated at the factory and does not require any
additional lubricant. Other than the recommended
cleaning, no further user maintenance should be
necessary.
Return the mixer to the nearest Authorized Sunbeam
Service Center for servicing or repairs.
cleaning
Caring For Your Mixer
8
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 14

MIXING AND BAKING SUGGESTIONS
• Ingredients should be added to the mixing bowl as they
are specified in the recipe. When combining dry and
wet ingredients, you may wish to moisten ingredients
on Speed 1 or 2, then turn to the desired mixing speed.
• Use the mixing speed that is recommended in the
recipe. Use the handy mixing guide on the speed
control dial of the mixer to help you find the correct
speed to use.
• If times are specified in the recipe, use them! BE
CAREFUL NOT TO OVERMIX. Overmixing can
cause the mixture to become very tough.
• Should an object, such as a spatula, fall into the bowl
while the mixer is operating, turn the mixer OFF
immediately. Then, remove the object.
• Remove beaters and place in sink for easy clean-up.
• When preparing your favorite dish, DO NOT exceed
3 1/2cups of flour in any recipe.
hints
Helpful Hints
To Order additional ACCESSORIES,
CALL 1-800-458-8407.
DESCRIPTION MODEL NO.
Dough Hooks 4964
Beater 4950
Large Glass Bowl 4938
Small Glass Bowl 4939
Large Stainless Steel Bowl 4951
Small Stainless Steel Bowl 4952
9
EJECTING THE BEATERS OR DOUGH HOOKS
After you’ve finished mixing, turn the speed control
dial to OFF and unplug the electric cord from the
electrical outlet. Push the ejector button located near
the handle to remove beaters or dough hooks.
Scrape excess batter off the beaters using a rubber or
plastic spatula. Do not strike beaters on the rim of
the bowl.
CLEANING YOUR MIXER
To clean the mixer, wipe the mixer head, stand and
turntable with a damp cloth, then dry. DO NOT
IMMERSE THE MIXER HEAD OR STAND IN
WATER. Avoid the use of abrasive cleaners, as they
may mar the finish of the mixer.
Wash the beaters and bowls in hot, soapy water after
each use. Rinse thoroughly and dry. Beaters and
bowls may also be washed in an automatic
dishwasher.
STORING YOUR MIXER
Store the mixer in a dry location, such as on a
countertop or table top, or in a closet or cupboard.
Insert the beaters into the proper sockets. Place the
dough hooks in the mixing bowl.
Store the bowl(s) on the turntable. The beaters will
help hold the bowl in position. Wind the electric cord
into a coil, secure it with a twist fastener.
MAINTENANCE
The motor of your stand mixer has been carefully
lubricated at the factory and does not require any
additional lubricant. Other than the recommended
cleaning, no further user maintenance should be
necessary.
Return the mixer to the nearest Authorized Sunbeam
Service Center for servicing or repairs.
cleaning
Caring For Your Mixer
8
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 14

dough hooks
Using Dough Hooks
BREAD MAKING INSTRUCTIONS
DO NOT LEAVE YOUR MIXER UNATTENDED
WHEN USING THE DOUGH HOOKS.
Ingredients should be added to the mixing bowl as
they are specified in the recipe.
Combine a small portion of the dry ingredients
with the wet ingredients. Mix on Speed 6. Continue
adding dry ingredients until the mixture becomes
sticky, then turn to Speed 1. Gradually add
remaining dry ingredients.
If there is high humidity in the air, it may be
necessary to add additional flour to the recipe. The
high humidity could also extend the amount of time
necessary for baking.
Guide the mixing bowl with your hands. Use
caution to keep hands out of the way of the dough
hooks.
Do not attempt to scrape the bowl while the mixer
is operating. Stop the mixer and scrape the sides of
the bowl as necessary. Use a rubber or plastic
spatula only.
DO NOT attempt to feed dough into the dough
hooks with your hands, a spatula or any other
utensil while the mixer is plugged into an outlet or
in operation.
If times are specified in the recipe, use them! BE
CAREFUL NOT TO OVERMIX. Overmixing can
cause the mixture to become tough. We suggest that
your total mixing time should be 6 – 8 minutes.
Should an object, such as a spatula, fall into the
bowl while the mixer is operating, turn the mixer
OFF immediately. Then remove the object. Remove
dough hooks and place in sink for easy clean-up.
11
breads
Breads
SPECIAL INSTRUCTIONS FOR MAKING
KNEADED BREADS
When making kneaded breads, your mixer will
require more care than when making ordinary
mixtures, such as cake batter and cookie dough.
The elasticity of the bread dough and the shape of the
dough hooks may cause your mixer to do some
unusual things.
The bowl may tend to rock back and forth. We
suggest that you guide the bowl with one hand to
help control the rocking action. AVOID GETTING
YOUR HANDS TOO NEAR THE DOUGH HOOKS!
The kneading action may cause the mixer to slide on
a slippery work surface. Be sure the work surface and
rubber feet on the bottom of the mixer are clean and
dry.
CAUTION: Do not use the mixer too near the edge of
a table or counter top, where it could fall off.
10
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 16

dough hooks
Using Dough Hooks
BREAD MAKING INSTRUCTIONS
DO NOT LEAVE YOUR MIXER UNATTENDED
WHEN USING THE DOUGH HOOKS.
Ingredients should be added to the mixing bowl as
they are specified in the recipe.
Combine a small portion of the dry ingredients
with the wet ingredients. Mix on Speed 6. Continue
adding dry ingredients until the mixture becomes
sticky, then turn to Speed 1. Gradually add
remaining dry ingredients.
If there is high humidity in the air, it may be
necessary to add additional flour to the recipe. The
high humidity could also extend the amount of time
necessary for baking.
Guide the mixing bowl with your hands. Use
caution to keep hands out of the way of the dough
hooks.
Do not attempt to scrape the bowl while the mixer
is operating. Stop the mixer and scrape the sides of
the bowl as necessary. Use a rubber or plastic
spatula only.
DO NOT attempt to feed dough into the dough
hooks with your hands, a spatula or any other
utensil while the mixer is plugged into an outlet or
in operation.
If times are specified in the recipe, use them! BE
CAREFUL NOT TO OVERMIX. Overmixing can
cause the mixture to become tough. We suggest that
your total mixing time should be 6 – 8 minutes.
Should an object, such as a spatula, fall into the
bowl while the mixer is operating, turn the mixer
OFF immediately. Then remove the object. Remove
dough hooks and place in sink for easy clean-up.
11
breads
Breads
SPECIAL INSTRUCTIONS FOR MAKING
KNEADED BREADS
When making kneaded breads, your mixer will
require more care than when making ordinary
mixtures, such as cake batter and cookie dough.
The elasticity of the bread dough and the shape of the
dough hooks may cause your mixer to do some
unusual things.
The bowl may tend to rock back and forth. We
suggest that you guide the bowl with one hand to
help control the rocking action. AVOID GETTING
YOUR HANDS TOO NEAR THE DOUGH HOOKS!
The kneading action may cause the mixer to slide on
a slippery work surface. Be sure the work surface and
rubber feet on the bottom of the mixer are clean and
dry.
CAUTION: Do not use the mixer too near the edge of
a table or counter top, where it could fall off.
10
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 16

tips
Tips
HOW TO SHAPE DOUGH FOR A LOAF PAN
1. Using a rolling pin, roll dough into a rectangle.
2. Roll dough into a loaf, starting from narrow end.
3. Flatten ends with sides of hands, as shown.
4. Pinch along seam to seal.
5. Fold ends under and place seam-side down in a
well-greased loaf pan.
13
tips
Tips
DOUGH RISING TIPS
A large, well-greased, glass mixing bowl is an
excellent container in which to raise or proof yeast
dough. The ideal temperature is 85°F / 30°C in an
area that is draft free. Cover with a light cloth. The
final rising should be after the dough has been
shaped and placed on the greased baking sheet or
pan recommended in the recipe. Again, cover the
rising dough and place in a warm, draft-free area. If
you live in a high altitude area, yeast breads will
require a shorter rising time. Allow the dough to rise
only until it has doubled in size. Slightly less flour
should be used because flour is dryer at higher
altitudes.
HOW TO PUNCH DOWN YEAST DOUGH
1. Plunge fist into center of risen dough to punch
out excess air.
2. Fold outer edges over into center. Turn dough
over and let rise until doubled, if recipe directions
so specify.
12
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 18

tips
Tips
HOW TO SHAPE DOUGH FOR A LOAF PAN
1. Using a rolling pin, roll dough into a rectangle.
2. Roll dough into a loaf, starting from narrow end.
3. Flatten ends with sides of hands, as shown.
4. Pinch along seam to seal.
5. Fold ends under and place seam-side down in a
well-greased loaf pan.
13
tips
Tips
DOUGH RISING TIPS
A large, well-greased, glass mixing bowl is an
excellent container in which to raise or proof yeast
dough. The ideal temperature is 85°F / 30°C in an
area that is draft free. Cover with a light cloth. The
final rising should be after the dough has been
shaped and placed on the greased baking sheet or
pan recommended in the recipe. Again, cover the
rising dough and place in a warm, draft-free area. If
you live in a high altitude area, yeast breads will
require a shorter rising time. Allow the dough to rise
only until it has doubled in size. Slightly less flour
should be used because flour is dryer at higher
altitudes.
HOW TO PUNCH DOWN YEAST DOUGH
1. Plunge fist into center of risen dough to punch
out excess air.
2. Fold outer edges over into center. Turn dough
over and let rise until doubled, if recipe directions
so specify.
12
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 18

15
notes
Notes
14
warranty
One-Year Limited Warranty
Sunbeam Products, Inc. (“Sunbeam”) warrants that for a period of ONE
year from the date of purchase, this product will be free from defects in
material and workmanship. Sunbeam, at its option, will repair or replace
this product or any component of the product found to be defective during
this warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value.
This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales receipt.
Proof of purchase is required to obtain warranty performance. Sunbeam
dealers, service centers or retail stores selling Sunbeam products do not have
the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting
from any of the following: negligent use or misuse of the product, use on
improper voltage or current, use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than Sunbeam or an
Authorized Service Center. Further, the warranty does not cover Acts of God
or nature, such as fire, flood, hurricanes and tornadoes.
Sunbeam shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty. Except to the extent
prohibited by applicable law, any implied warranty of merchantability or
fitness for a particular purpose is limited in duration to the duration of the
above warranty. Some states, provinces or jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or limitations
on how long an implied warranty lasts, so the above limitations of exclusion
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state or province to
province. NOTE: For products aquired outside the United States, please see
country specific warranty insert.
HOW TO OBTAIN WARRANTY SERVICE
Take the product to an Authorized Sunbeam Service Center. You can find the
nearest Authorized Sunbeam Service Center by calling 1 800 458-8407 or
visit our Web site at www.sunbeam.com.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 20

15
notes
Notes
14
warranty
One-Year Limited Warranty
Sunbeam Products, Inc. (“Sunbeam”) warrants that for a period of ONE
year from the date of purchase, this product will be free from defects in
material and workmanship. Sunbeam, at its option, will repair or replace
this product or any component of the product found to be defective during
this warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value.
This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales receipt.
Proof of purchase is required to obtain warranty performance. Sunbeam
dealers, service centers or retail stores selling Sunbeam products do not have
the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting
from any of the following: negligent use or misuse of the product, use on
improper voltage or current, use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than Sunbeam or an
Authorized Service Center. Further, the warranty does not cover Acts of God
or nature, such as fire, flood, hurricanes and tornadoes.
Sunbeam shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty. Except to the extent
prohibited by applicable law, any implied warranty of merchantability or
fitness for a particular purpose is limited in duration to the duration of the
above warranty. Some states, provinces or jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or limitations
on how long an implied warranty lasts, so the above limitations of exclusion
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state or province to
province. NOTE: For products aquired outside the United States, please see
country specific warranty insert.
HOW TO OBTAIN WARRANTY SERVICE
Take the product to an Authorized Sunbeam Service Center. You can find the
nearest Authorized Sunbeam Service Center by calling 1 800 458-8407 or
visit our Web site at www.sunbeam.com.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 20

DONOT SEND THIS PRODUCT TO THE PLACE OF PURCHASE
For product questions:
Sunbeam Consumer Service
P.O. Box 948389
Maitland, FL 32794-8389
1.800.458.8407
www.sunbeam.com
D O N OT S END P RODUCT TO THE A BOVE A DDRESS
©2002 Sunbeam Products, Inc. All rights reserved.
Sunbeam is a registered trademark of Sunbeam Products, Inc.
Distributed by Sunbeam Products, Inc.
Boca Raton, FL 33431
U.S. Patent Nos. 5,782,558; D395,572
Printed in China P.N. 109541
NO ENVÍE ESTE PRODUCTO AL LUGAR DONDE LO COMPRÓ
Para hacer consultas sobre el producto:
Sunbeam Consumer Service
P.O. Box 948389
Maitland, FL 32794-8389
1.800.458.8407
www.sunbeam.com
N O ENVÍE ESTE PRODUCTO A LA DIRECCIÓN QUE APARECE MÁS ARRIBA
©2002 Sunbeam Products, Inc. Todos los derechos reservados.
Sunbeam es marca comercial registrada de Sunbeam Products, Inc.
Distribuido por Sunbeam Products, Inc.
Boca Raton, FL 33431
Nos. de patente EE. UU. 5,782,558; D395,572
Impreso en China N.P. 109541
SUN400_2377_StandMxr_mech 3/14/02 11:38 AM Page 22