Sunco EM 2HFL-1PK User manual

The Brighter Choice
2 HEAD LED EMERGENCY LIGHT
Install Guide and Manual
EASY INSTALLATION
WARNING
1.
2.
5.
3.
4.
5.
6.
7.
To reduce the risk of fire, electric shock or injury to people:
• This product should be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazards involved.
• Abide by related regional and local laws or regulations.
• In accordance with regulations, your emergency lighting system must be tested monthly for
a minimum of 30 seconds and annually for 180 minutes. To check, press the “TEST” button.
If working properly, the lamps on the unit should on.
• Proper grounding is required to ensure safety.
• Do not use outdoors or mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be subject to
tampering by unauthorized personnel.
• Check for damage during shipping prior to install. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this LED light fixture.
• To ensure efficient light, regularly clean the light panel. Do not clean with harsh solvents.
• Use safety precautions. Safety eyeglasses and gloves are recommended.
Turn off circuit breaker that provides power to
the light switch.
Unsnap backplate using 2 slots at bottom of
light fixture. Set aside housing.
Complete the battery connection inside housing.
Feed fixture leads through the back plate and
connect to AC power supply wires in your junction
box (not included).
• For 120V, use black and white wires.
• For 277V, use red and white wires.
Attach back plate to J-Box and secure with screws.
Align the snaps and push housing onto the back plate.
Turn on circuit breaker and test light.
Allow battery to charge for 24 hours prior to use as an
emergency light source.
Turn Power OFF
J-Box Mounting
REMOTECAPABLE REGULAR
Required Tools: Drill, Ladder,
Pliers, Screwdriver .
Light Housing
X1 X3 X2 X2
Wire Nuts Plastic Anchors Screws
WIRING DIAGRAM
NOTE:
Use 180-22AWG
standarded wire
to connect remote
lamp heads.
NOTE:
Unused input lead
must be properly
insulated with
wire nut or other
approved method.
Battery Connector
Plug In
COMPONENTS

The Brighter Choice
1.
2.
4.
3.
5.
6.
7.
Voltage
Input Power
Damp
6000K ± 500K
1.65lbs
1 year
120/277V
2.4W
Color temperature
Weight
Warranty
Suitable for Locations Ingress
Turn off circuit breaker that provides power to
the light switch.
Unsnap backplate using 2 slots at bottom of
light fixture. Set aside housing.
Complete the battery connection inside housing.
Secure backplate to wall surface. Route wires
through hole in conduit flange and make conduit
connection.
• For 120V, use black and white wires.
• For 277V, use red and white wires.
Align the snaps and push housing onto the back plate.
Turn on circuit breaker and test light.
Allow battery to charge for 24 hours prior to use as an
emergency light source.
OPERATION
EASY INSTALLATION Wall Mount with Conduit
Required Tools: Drill, Ladder,
Pliers, Screwdriver .
•During an electrical power failure, the 2 LED lamps will automatically come on for
a minimum of 180 minutes.
•To test (after charging for 24 hours), depress the “TEST” switch on bottom of the
light fixture. The 2 emergency LED lamps will illuminate. When the switch is
released, the lamps will go off.
IMPORTANT
•Charge the battery for at least 24 hours prior to use as safety lighting.
•Battery in this unit may not be fully charged. After electricity is hooked up to the unit,
let the battery charge for at least 24 hours. It is then ready for normal operation.
•Use flexible conduit only.
•Unused wires must be capped with a wire nut.
SPECIFICATIONS
Turn Power OFF
Battery Connector
Plug In
2 HEAD LED EMERGENCY LIGHT
Install Guide and Manual
Light Housing
X1 X3 X2 X2
Wire Nuts Plastic Anchors Screws
COMPONENTS