Sunco MOTION SHOP LIGHT User manual

www.suncolighting.com
[phone] CUSTOMER SERVICE
[email protected]
SALES
[email protected]
163 W Cochran St,
Simi Valley, CA 93065
Still having trouble? Contact us!
MOTION SHOP LIGHT
Install Guide and Manual
COMPONENTS
Turn off circuit breaker that provides power to the light
switch for the recessed lights.
Mounting surface must be able to support the weight of
the fixture.
Plaster board - #8 eye hook screw with plastic anchors,
or expansion bolts (not included);
Plaster board thickness should be 3/8 inch.
Depending on your lighting plan, space the anchors
accordingly.
•Link up to 4
Hang the lose end of the S hook chain on screw
eye hook in ceiling
Attach two anchors to ceiling. Spacing between
hooks should be 47.25” inches apart, then screw in
the screw eye hooks into the anchors.
Required Tools: Drill, Ladder, Hammer,
Pliers, Tape Measure, Pencil
Plug in power cord to electrical outlet
Turn on circuit breaker and test light
1.
2.
4.
7.
Install one S hook into each end of the chain,
then crimp the end attached to the chain with
pliers. Leaving the other side open.
Install the S hook from one end of the chain into
the end cap, then crimp the hook with pliers.
Repeat on the other side.
5.
6.
3.
8.
9.
Wattage
Voltage
Suitable for Locations Ingress
Housing
40W
120V
Damp
Aluminium+PC
Weight
Warranty
2.70lbs
7 years
SPECIFICATION
WARNING
Turn Power OFF
47.25” apart
Link up
4 shoplights
together
Connect to
additional
shoplight
Connect to
Power Outlet Step 1
Step 2
Front
Side
Turn Power ON
Chain Link “S” Hook Screw Eye Hook Plastic Anchor Screw
X4X6X2X4X2
All electrical connections must be in accordance with local and National Electric
Code (N.E.C.) standards. Consult a qualified electrician if you are unfamiliar with
proper electrical wiring connections. Please review
instructions carefully before proceeding.
WARNING: Risk of fire or electric shock. Do not alter, relocate or remove wiring
during installation.
This fixture complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: Not for use with dimmers. Do not install directly over a heat source.

www.suncolighting.com
[phone] CUSTOMER SERVICE
[email protected]
SALES
[email protected]
163 W Cochran St,
Simi Valley, CA 93065
Still having trouble? Contact us!
MOTION SHOP LIGHT
Install Guide and Manual
COMPONENTS
Turn off circuit breaker that provides power to the light
switch for the recessed lights.
Mounting surface must be able to support the weight of
the fixture.
•Plaster board thickness should be 3/8 inch
Depending on your lighting plan, space the anchors
accordingly.
•Link up to 4
Plug in power cord to electrical outlet.
Install 4 plastic anchors 46.5 inches apart and
3.189 inches apart, screw in an eye hook into each
anchor. Gap between the ceiling and the cap nut
should be 0.75 inch
•Recommended screw dimensions: ST4X30
Turn on circuit breaker and test light
1.
2.
4.
6.
Lift fixture up to screws and slide to one side to
secure into place. Fixture should be firmly fixed
against screws.
5.
3.
7.
STYLE 1 AND STYLE 2 OF INFRARED INDUCTION RANGE
Turn Power OFF
Link up
4 shoplights
together
Connect to
additional
shoplight
Connect to
Power Outlet
Turn Power ON
Chain Link “S” Hook Screw Eye Hook Plastic Anchor Screw
X4X6X2X4X2 Required Tools: Drill, Ladder, Hammer,
Pliers, Tape Measure, Pencil
46.5” apart
0.33”
3.189”
0.14”
Human infrared
sensor
The recomended installation
height is OC 2.8~3.5m
Movement in this direction
sensing distance OA/OB<2m
Movement in this direction
sensing distance OB<5m
STYLE 1
Human infrared
sensor
The recomended installation
height is OC 2.8~3.5m
Movement in this direction
sensing distance OA/OB<2m
Movement in this direction sensing distance OB<5m
STYLE 2